Oki B6200 Maintenance Manual page 148

When the cursor is positioned at the left end of the partition size, pressing the " ← "
key allows you to return to the [Partition setting A 40] screen in an upper
hierarchical level.
9. The partition size is fixed by pressing the "FEED / SELECT" key. Then, "*" is marked at the right
end of the changed value.
10. Show the next initial value screen [Partition setting B 40] for the size-adjustable partition using the
"FEED / SELECT" key. You can select the next (or previous) initial value screen for a size-
adjustable partition using the " ↓ " or " ↑ " key.
11. When you have shown the initial value screen [Partition settingD 30] for the size-adjustable partition
using the " ↓ " key, the execution instruction screen [Partition setting If OK press SEL] is shown by
pressing the " ↓ " key again.
12. Execute a partition size setting using the "FEED / SELECT" key. During the execution, [Partition
setting In progress] is shown.
• When the execution has been completed normally, the [Partition setting Completed] screen is
shown.
• When the execution has been completed abnormally, the [Partition setting Completed
abnormally] screen is shown.
13. Show the [Change Partition size Please exit Diag] screen to prompt you to exit the Diag mode,
using the " ←" or "MENU" key.
14. Press the "MENU" key to return to the common menu screen [Diag. Menu Fault Diag.].
<Executing a setup>
Procedure:
1. Enter the Diag (C/E) mode, and select [Diag. Menu Fault Diag.] in the same hierarchical level using
the " ↓ " key.
2. Select the [Fault Diag. DC140 Monitor] screen in a lower level using the " → " key.
3. Select [Fault Diag. DC355 HDD DIAG] in the same hierarchical level using the " ↓ " key.
4. Select the [DC355 HDD DIAG Read Verify Test] screen using the " → " key.
5. Select [DC355 HDD DIAG Setup] in the same hierarchical level using the " ↓ " key.
6. Show the setup setting item screen (Figure-4) using the " → " key. Then, to set up all the partitions,
follow the step below. To set up a partition individually, go to the step 7.
(1) Select the execution instruction screen [Setup If OK press SEL] in the same hierarchical level
using the " ↓ " key.
(2) Show the confirmation message screen [Clear HDD data If OK press SEL] using the "FEED /
SELECT" key.
(3) Execute a setup using the "FEED / SELECT" key again. During the execution, [Setup In
progress] is shown.
• When the execution has been completed normally, the [Setup Completed] screen is
shown.
• When the execution has been completed abnormally, the [Setup Completed abnormally]
screen is shown.
(4) Press the "MENU" key to return to the common menu screen [Diag. Menu Fault Diag.].
7. Show the partition selection screen [Partition A] using the " → " key. You can select the partitions
[Partition A], [Partition B], [Partition C], [PartitionD], [Partition H] and [Partition ALL] in that order,
using the " ↓ " or " ↑ " key.
8. Use the "FEED / SELECT" key to fix the partition to be set up.For example, if you select [Partition
D] and fix it, "*" is marked at the right end of the partition name (i,e. [Partition D*]).
9. Show the execution instruction screen [Setup If OK press SEL] using the "FEED / SELECT" key.
10. Show the confirmation message screen [Clear HDD data If OK press SEL] using the "FEED /
SELECT" key.
Setup
Partition ALL
2 - 24
Chapter 2 Operation of Diagnostic