Oki B6200 Maintenance Manual page 27

Chain Link Fault Items
Fuser Exit Sensor On
010 105
Jam
Fuser Exit Sensor Off
010 106
Jam
010 112 Exit Out Early Jam
Duplex Pre Regi Sensor
010 128
On Jam
Duplex Path 1 Sensor On
010 132
Jam
Regi.SNR On Jam <Dup
010 164
Miss Feed Jam>(not wait)
<OCT failure> Offset Fail
010 347
(OCT)
Fuser STS Front
010 349
Disconnection Fail
010 420 Fuser Unit Pre Warning
OCT Jam 1 (Paper doesn'
011 108
t reach OCT)
OCT Jam 2 (Paper is not
011 109
ejected form OCT)
Faceup Tray is opened
012 300
while printing.
012 951 OCT_FULL_STACK
012 952 FaceUP Tray Open
Conditions of detect/Methods of treatment
Fuser Exit Sensor doesn' t detect paper from REGI. Clutch ON after
specific time passed.
Slip of Feed Roll, wear, fail of rotation
Defect of Fuser Exit Sensor
Disconnection of wires from Fuser Exit Sensor J4247-1 to MCU PWB
J11-10 or loose connection
Paper doesn' t go through Fuser Exit Sensor though the specific time
passed after REGI. Sensor go through.
Check whether paper is not rolled to Heat Roll.
Defect of Fuser Exit Sensor
Short out the wires from Fuser Exit Sensor J159-1 to MCU PWB J15-
B3.
Fuser Exit Sensor becomes OFF in shorter time than specified after
Fuser Exit Sensor detected the top of paper. (Turning to OFF is too
early.)
Check whether paper is not rolled to Fuser Exit Roll.
Paper comes to Regi from Sensor DUP too fast.
Dirt or defect of Sensor DUP
Paper is not ejected from Sensor DUP within the specific time, or
Sensor DUP is On while Warming up.
Slip of Feed Roll, wear, fail of rotation, scrap of paper is left
Dirt or defect of Sensor DUP
Paper doesn' t come to Reg from Sensor DUP within the specific time.
Slip of Feed Roll, wear, fail of rotation
Dirt or defect of Sensor DUP
Fail to communication with machineCheck the connection to the
machine, and replace PWBA OCT if it is no problem.
Detect Fuser trouble.
Replace Fuser Assy if Power OFF and ON cannot recover the FAIL.
In the case that PV of Fuser comes to the specified value and the life
time to be end.
Replace Fuser Unit, and Reset HFSI counter.
Paper doesn' t come to OCT Sensor from Exit Sensor within the
specific time.
Slip of Feed Roll, wear, fail of rotationDirt or defect of Sensor OCT
Paper is not ejected from OCT Sensor within the specific time, or OCT
Sensor is On while Engine Warming up.
Slip of Feed Roll, wear, fail of rotation
Dirt or defect of Sensor OCT
Detect Cover Interlock Open of FaceUpTray in a job,or Standard
mode,or Faceup Tray is opened while printing in OCT mode.
Dirt or defect of Sensor Face Up Open
Detect Full Stack(OCT)
Detect paper left in the offset ejecting tray.
Remove paper in IOT Face Down Tray.
Dirt or defect of Sensor Full Stack
Detect that Faceup Tray is opened though printing out to Facedown
Tray or OCT is specified.
Dirt or defect of Sensor Face Up Open
1 - 11
Chapter 1 Troubleshooting
Ref FIP
FIP1.7
FIP1.8
FIP1.29
(Separate
volume)
FIP1.28
(Separate
volume)
FIP1.29
(Separate
volume)
FIP1.30
(Separate
volume)
FIP1.38
(Separate
volume)
FIP1.42
(Separate
volume)
FIP1.3
FIP1.17
FIP1.39
(Separate
volume)
FIP1.43
(Separate
volume)
FIP1.41
(Separate
volume)
FIP1.44
FIP1.43
(Separate
volume)