Table of Contents
Advertisement
RRP3.23 GUIDE CST L 250 (PL 3.2.34)
[Removal]
1)
Remove 250 SHEET PAPER TRAY. (RRP 2.1)
2)
Remove 250 SHEET FEEDER RIGHT COVER. (RRP 3.4)
3)
Remove 250 SHEET FEEDER LEFT COVER. (RRP 3.2)
4)
Remove 250 SHEET FEEDER CHUTE ASSEMBLY. (RRP 3.3)
5)
Remove CLUTCH ASSY PH. (RRP 3.7)
6)
Remove DRIVE ASSY FEED 250. (RRP 3.5)
7)
Remove HOUSING ASSY FEED. (RRP 3.14)
8)
Remove CHUTE ASSY RETARD 250. (RRP 3.26)
9)
Remove a screw (silver, tap, 8mm) that fix CAP (PL 3.2.43) to 250 SHEET FEEDER
ASSEMBLY.
10) Remove CAP from 250 SHEET FEEDER ASSEMBLY.
11) Remove the connector (P/J438) on PWBA TRAY CONT.
12) Remove five screws (silver, tap, 6mm) that fix GUIDE CST L 250 (PL 3.2.34) to 250 SHEET
FEEDER ASSEMBLY.
13) For removing FUSER CHUTE INTERLOCK (PL3.2.9), slide GUIDE CST L 250 to right side.
Remove GUIDE CST L 250 together with SPG LOCK CST LL (PL3.2.31), STOPPER CST L
(PL3.2.35), SNR CST (PL3.2.36) and HARNESS-ASSY FEED SW (PL3.2.27).
14) Remove STOPPER CST L. (RRP 3.24)
15) Remove SNR CST. (RRP 3.25)
[Replacement]
1)
Attach SNR CST. (RRP 3.25)
2)
Attach STOPPER CST L. (RRP 3.24)
Be sure that harness is not caught between 250 SHEET FEEDER ASSEMBLY and
GUIDE CST L 250 when carrying out the work shown below.
3)
Put FUSER CHUTE INTERLOCK in the hole of rear side on GUIDE CST L 250, match the
boss of GUIDE CST L 250 to the hole of 250 SHEET FEEDER ASSEMBLY and attach GUIDE
CST L 250. Pull HARNESS-ASSY FEED SW out from the hole of 250 SHEET FEEDER
ASSEMBLY.
4)
Fix GUIDE CST L 250 to 250 SHEET FEEDER ASSEMBLY using five screws (silver, tap,
6mm).
5)
Attach connector (P/J438) to PWBA TRAY CONT.
6)
Match the boss of CAP to the hole in 250 SHEET FEEDER ASSEMBLY, attach CAP.
7)
Fix CAP to 250 SHEET FEEDER ASSEMBLY using a screw (silver, tap, 8mm).
8)
Attach CHUTE ASSY RETARD 250. (RRP 3.26)
9)
Attach HOUSING ASSY FEED. (RRP 3.14)
10) Attach DRIVE ASSY FEED 250. (RRP 3.5)
11) Attach CLUTCH ASSY PH. (RRP 3.7)
12) Attach 250 SHEET FEEDER CHUTE ASSEMBLY. (RRP 3.3)
13) Attach 250 SHEET FEEDER LEFT COVER. (RRP 3.2)
14) Attach 250 SHEET FEEDER RIGHT COVER. (RRP 3.4)
15) Attach 250 SHEET PAPER TRAY. (RRP 2.1)
Chapter 3 Removal and Replacement Procedures (RRPs)
3 - 109
Advertisement
Chapters
Table of Contents
