Table of Contents
Advertisement
Network and Security Manager Administration Guide
136
Click Show Device Commands to display a list of CLI commands. The commands
enable management and set the management IP address to the Device Server IP
address, enable the Management Agent, set the Unique External ID, and set the device
OTP.
Copy and paste these commands into a text file, and then send the commands to the
device administrator. The device administrator must make a Telnet connection to the
physical device, paste the commands, and execute them to enable NSM management
of the device.
NOTE: The device administrator can also use a console connection to
execute the commands on the physical device. However, the commands
must be entered three at a time to ensure that the device receives all
commands.
Click OK to dismiss the Commands window and complete the Activate Device wizard.
8.
Check the device configuration status by holding your mouse cursor over the device
9.
in Device Manager, or by checking the configuration status in Device Monitor). When
the device connects, the status displays "Update Needed", indicating that the device
has connected but the management system has not pushed the device configuration
yet.
Update the device configuration by right-clicking the device and selecting Update
10.
Device. The Job Information box displays the job type and status for the update. When
the job status displays successful completion, click Close.
After the update is complete, the device status displays as "Managed", indicating that
the device has connected and the management system has successfully updated the
device configuration.
Activating a Junos Device
The procedure for activating a device with an unknown IP address is similar for all Junos
devices. This procedure requires specific actions to be taken on the device in addition to
those taken in the NSM UI. In NSM, you must complete the Activate Device workflow.
You must also make sure the device is properly installed and configured with login
credentials for the NSM administrator, and configure the device to connect with NSM.
Finally, you must load the modeled configuration onto the device:
Install the device and configure it with logon credentials for the NSM administrator:
1.
Connect the device to the network and configure one of the interfaces so that the
a.
device can reach the NSM device server.
Copyright © 2010, Juniper Networks, Inc.
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW CONTROLLER 2.0.4 -
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - AQL EVENT AND FLOW QUERY CLI GUIDE
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - EVENT CATEGORY CORRELATION REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - SNMP AGENT GUIDE REV 1
- Juniper STRM LOG MANAGEMENT 2008.2 - S 6-2008