Table of Contents
Advertisement
Network and Security Manager Administration Guide
122
NOTE: Secure Access devices are more commonly configured as clusters.
See "Adding Clusters" on page 151 for details.
The following sections explain how to add a Secure Access or Infranet Controller device:
Install and Configure the Secure Access or Infranet Controller Device on page 122
Add the Device in NSM on page 122
Configure and Activate the NSM Agent on the Secure Access or Infranet Controller
Device on page 124
Confirm Connectivity and Import the Device Configuration into NSM on page 124
Install and Configure the Secure Access or Infranet Controller Device
Before you can add a Secure Access or Infranet Controller device to NSM, the device
must be installed and configured, and logon credentials for an NSM administrator must
be configured for it. Perform the following steps:
Select System > Network > Overview on the device administrator's console and
1.
ensure that basic connection information is configured on the device (network interface
settings, DNS settings, and password).
Select Authentication > Auth. Servers and enter the username and password of the
2.
NSM administrator in the applicable authentication server.
NOTE: Only password-based authentication servers can be used. One-time
password authentication is not supported.
Select Administrators > Admin Roles and create an NSM agent role.
3.
Select Administrators > Admin Realms and create a new NSM agent administrator
4.
realm for the NSM agent on the device. Use role mapping to associate the NSM agent
role and realm. Do not apply any role or realm restrictions for the NSM agent role or
realm.
NOTE: You cannot use NSM to add or manage a Secure Access device that
has Host Checker policies enabled for an admin user.
For complete details on installing and configuring Secure Access devices, see the Secure
Access Administration Guide.
For complete details on installing and configuring Infranet Controller devices, see the
Unified Access Control Administration Guide.
Add the Device in NSM
To add the device in the NSM UI, follow these steps:
Copyright © 2010, Juniper Networks, Inc.
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW CONTROLLER 2.0.4 -
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - AQL EVENT AND FLOW QUERY CLI GUIDE
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - EVENT CATEGORY CORRELATION REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - SNMP AGENT GUIDE REV 1
- Juniper STRM LOG MANAGEMENT 2008.2 - S 6-2008