Sharp MX-4100N Service Manual page 110

2) Select the copy mode to be adjusted with the scroll key.
Display/Item
A AUTO1 Auto 1
B AUTO2 Auto 2
C TEXT Text
D TEXT/PRINTED Text/Printed
PHOTO Photo
E TEXT/PHOTO Text/Photograph
F PRINTED PHOTO Printed Photo
G PHOTOGRAPH Photograph
H MAP Map
I TEXT Text (Copy
(COPY TO COPY) document)
J TEXT/PRINTED Text/Printed
PHOTO Photo (Copy
(COPY TO COPY) document)
K PRINTED PHOTO Printed Photo
(COPY TO COPY) (Copy document)
L LIGHT Light document
3) Enter the adjustment value with 10-key and press [OK] key.
When adjusting the copy density on the low density part, select
"LOW" mode and change the adjustment value. When adjust-
ing the copy density on the high density part, select "HIGH"
mode and change the adjustment value.
When the adjustment value is increased, the copy density is
increased. When the adjustment value is decreased, the copy
density is decreased.
4) Press [CLOSE] key in this simulation mode to jump to the nor-
mal copy mode. Make a copy and check the adjustment result
Switch the simulation mode and the normal copy mode alter-
nately, and adjust and check the adjustment result.
Repeat switching the adjustment mode (SIM 46-1) and the
normal copy mode and changing the adjustment value and
checking the adjustment result until a satisfactory result is
obtained.
To increase the density, increase the adjustment value. To
decrease the density, decrease the adjustment value.
20-F Copy color balance adjustment (Color
balance adjustment at each density level in
each color copy mode)
(Normally not required)
This adjustment is needed in the following situations:
* When there is necessity to change the color balance and gamma
by each the copy mode individually.
* U2 trouble has occurred.
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
This is to adjust the color balance at each density level in each
color copy mode. Normally individual adjustments are not required.
This adjustment is executed when there is a request from the user.
Setting
Content Default
range
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
MX-5001N ADJUSTMENTS 5 – 68
1) Enter the SIM 46-10 mode.
TEXT
C
10-key
OK
EXECUTE
2) Select the copy mode to be adjusted with the mode key.
3) Select a color to change the adjustment value with the color
key.
4) Select the density level (point) to be adjusted with the scroll
key.
Density level
Item/Display
(Point)
A POINT1 Point 1
B POINT2 Point 2
C POINT3 Point 3
D POINT4 Point 4
E POINT5 Point 5
F POINT6 Point 6
G POINT7 Point 7
H POINT8 Point 8
I POINT9 Point 9
J POINT10 Point 10
[SYSTEM
SETTINGS] key
EXECUTE
or end of print
Adjustment
Default
value range
245 - 755 500
245 - 755 500
245 - 755 500
245 - 755 500
245 - 755 500
245 - 755 500
245 - 755 500
245 - 755 500
245 - 755 500
245 - 755 500