Sharp MX-4100N Service Manual page 109

2) Select the copy mode to be adjusted with the scroll key.
Display/Item
A AUTO Auto
B TEXT Text
C TEXT/PRINTED Text/Printed
PHOTO Photo
D TEXT/PHOTO Text/Photograph
E PRINTED PHOTO Printed Photo
F PHOTOGRAPH Photograph
G MAP Map
H LIGHT Light document
I TEXT Text (Copy
(COPY TO COPY) document)
J TEXT/PRINTED Text/Printed
PHOTO Photo (Copy
(COPY TO COPY) document)
K PRINTED PHOTO Printed Photo
(COPY TO COPY) (Copy document)
L TEXT Text
(COLOR TONE (Color tone
ENHANCEMENT) enhancement)
M TEXT/PRINTED Text/Printed
PHOTO Photo
(COLOR TONE (Color tone
ENHANCEMENT) enhancement)
N TEXT/PHOTO Text/Photograph
(COLOR TONE (Color tone
ENHANCEMENT) enhancement)
O PRINTED PHOTO Printed Photo
(COLOR TONE (Color tone
ENHANCEMENT) enhancement)
P PHOTOGRAPH Photograph
(COLOR TONE (Color tone
ENHANCEMENT) enhancement)
Q MAP Map
(COLOR TONE (Color tone
ENHANCEMENT) enhancement)
R SINGLE COLOR Single color
S SINGLE COLOR Single color
(COPY TO COPY) (Copy document)
T TWO COLOR Two-color
(Red/Black) copy
U TWO COLOR Two-color
(COPY TO COPY) (Red/Black) copy
(Copy document)
3) Enter the adjustment value with 10-key and press [OK] key.
When adjusting the copy density on the low density part, select
"LOW" mode and change the adjustment value. When adjust-
ing the copy density on the high density part, select "HIGH"
mode and change the adjustment value.
When the adjustment value is increased, the copy density is
increased. When the adjustment value is decreased, the copy
density is decreased.
Setting
Content Default
range
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
LOW 1 - 99 50
HIGH 1 - 99 50
MX-5001N ADJUSTMENTS 5 – 67
4) Press [CLOSE] key in this simulation mode to jump to the nor-
mal copy mode. Make a copy and check the adjustment result
Switch the simulation mode and the normal copy mode alter-
nately, and adjust and check the adjustment result.
Repeat switching the adjustment mode (SIM 46-1) and the
normal copy mode and changing the adjustment value and
checking the adjustment result until a satisfactory result is
obtained.
To increase the density, increase the adjustment value. To
decrease the density, decrease the adjustment value.
20-E Copy density adjustment (Each
monochrome copy mode) (Whole
adjustment) (Normally unnecessary to
adjust)
This adjustment is needed in the following situations:
* When there is necessity to change copy density of the low den-
sity and high density part at each copy mode individually.
* When there is necessity to change the density gradient of the
copy by each the copy mode individually.
* When there is necessity to change all copy density by each the
copy mode individually.
* U2 trouble has occurred.
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
The density is adjusted in each copy mode individually. Normally
individual adjustments are not required. When there is a request
from the user, execute this adjustment.
1) Enter the SIM 46-2 mode.
OK