Displaying The Macro Attachment Settings; Executing A Macro By Macro Attachment - Sony XVS-9000 User Manual

pair number is assigned. Further, if you delete any of
these assignments, this deletes all assignments to the
same pair number.
- If you assign a pair number to a different cross-point
button, the macro attachment settings are also
transferred to the new cross-point button.
• When macro attachment data is loaded and overwrites
existing data, this also changes the button number mode
or pair number mode setting.
Displaying the Macro Attachment
Settings
In the Macro >Attachment >Attachment menu (5421), you
can display the macro attachment list to check the macro
attachment settings.
The following items are displayed in the list.
• Block: Panel block names.
• Button: Names of buttons with macro attachments (up
to 30 characters).
• Reg: Assigned register numbers.
• Name: Names of macro registers.
• Mode: Macro modes (Pre/Post/Only/---)
Above the list is shown the name of the block and macro
attachment assigned button selected in the list.
1) "---" indicates no macro mode is set.
For details about macro modes, see "Setting a macro
attachment" (page 360).
For details about the macro attachment list contents, see
"Content Displayed in Macro Attachment List"
(page 528).
To move within the list by blocks
You can move quickly from the current block to another
block to check the settings for that block by pressing the
buttons in the <Block Select> group.
• P/P: Move to a block in the PGM/PST row.
• M/E-1: Move to a block in the M/E-1 row.
• M/E-2: Move to a block in the M/E-2 row.
• M/E-3: Move to a block in the M/E-3 row.
• M/E-4: Move to a block in the M/E-4 row.
• M/E-5: Move to a block in the M/E-5 row.
• Aux: Move to a block in the AUX row.
• Others: Move to a block other than in the PGM/PST, M/
E-1 to M/E-5, and AUX rows.
Executing a Macro by Macro
Attachment
A macro assigned to a button or fader lever in a macro
attachment becomes executable when macro attachments
are enabled. Macro attachments are enabled/disabled using
the following buttons.
Macro
attachment
location
M/E and PGM/
PST banks
Other than M/E
and PGM/PST
banks
You can set to permanently enable or disable macro
attachments without using buttons.
For details, see "Setting the Macro Execution Mode"
(page 423).
1)
Executing a macro assigned to a button
1
Depending on the location of the button you want to
execute, press the [MACRO ATTACH ENABLE]
button (or button assigned with the "Macro
Attachment Enbl" command), turning it on.
If using the [MACRO ATTACH ENABLE] button on
the cross-point pad or a memory recall button in the
utility/shotbox control block, press it, turning it on
orange.
2
Press the button with a set macro attachment.
This recalls the macro register assigned to the button,
and the macro is executed as follows, according to the
operation mode.
Pre macro mode: The macro is executed first, and
Post macro mode: The button function is executed
Macro only mode: The button function is not
During macro execution, the selected button blinks.
Notes
• It is not possible to execute more than one macro at a
time. Therefore, even if you simultaneously press
multiple buttons for which macro attachments are set,
only one macro is executed.
• If a button is pressed twice during macro execution or
when the macro is stopped, or if another macro is
recalled, the following operation depends on a setting in
the Setup menu.
363
Button
Press [MACRO ATTACH ENABLE] on the
cross-point pad of the cross-point control
block.
Press the following buttons assigned with
the "Macro Attachment Enbl" utility
command.
• User preference buttons in the menu
panel
• Memory recall buttons in the utility/
shotbox control block
• Cross-point buttons of the cross-point
control block (utility/shotbox mode)
then the button function is executed.
first, and then the macro is executed.
executed, and the macro only is executed.