Settings Relating To Signal Inputs - Sony XVS-9000 User Manual

Settings Relating to
Signal Inputs
Configures settings for primary inputs.
The following input connector boards can be installed in
the XVS-9000/8000/7000/6000.
• XVS-9000
Input connector board
XKS-S9112 12G-SDI Input Board
• XVS-8000/7000/6000
Input connector board
XKS-S8110 SDI Input Connector Board
XKS-S8111 SDI Input and FC Connector
Board
XKS-S8112 12G-SDI Input Board
XKS-T8110 IP Input Connector Board
XKS-Q8111 QSFP IP Input Connector
Board
a) Interface configured in the Engineering Setup >System >Network Config
>Net I/F Protocol menu (7311.3)
The maximum number of inputs on the XVS-9000 is 160
(80 for 4K format), on the XVS-8000 is 160 (40 for 4K
format), on the XVS-7000 is 112 (28 for 4K format), and
on the XVS-6000 is 64 (16 for 4K format).
Note
59.94 (2×) format input signals are supported on the
XKS-S8110 SDI Input Connector Board only.
Network connector board (XKS-T8110/
XKS-Q8111) restrictions
• Only the following signal format inputs are supported,
depending on the interface.
- NMI: 3840×2160P 2SI, 1080P, 1080i
- ST2110: 1080i
• Only odd-numbered inputs can be configured if the
signal format is 1080P for NMI or 1080i for ST2110.
The number of inputs is half the number on an SDI
connector board (XKS-S8110/XKS-S8111/
XKS-S8112).
4K format input settings
• XVS-9000 input setting: When the switcher signal
format is 3840×2160P 2SI, a 4K (12G) signal is input as
a 12G×1 signal. The input setting is available for odd-
numbered inputs only.
When 3840×2160P 2SI 3G or 3840×2160P SQD signals
are input, 3G×4 input signals are assigned as a single
group to a 4K signal. The input setting is specified for
the first number input in each group of four inputs in the
same way as for the XVS-8000/7000/6000.
• XVS-8000/7000/6000 input setting: Four inputs are
assigned as a single group to a 4K signal.
A single group comprises four inputs in numeric order
starting from the first input, and settings are applied to
the first number input in each group.
Input connector number
1, 2, 3, 4
5, 6, 7, 8
Interface
9, 10, 11, 12
SDI
13, 14, 15, 16
(and so on)
When using an XKS-S8112 12G-SDI Input Board,
Interface
3840×2160P 2SI 12G signals are input as a 12G×1
SDI
signal, but the input setting is available only for the first
SDI
number input in each group of four inputs.
Dedicated inputs
SDI
On the XVS-8000, dedicated input connectors 1 to 16 can
NMI
be used by installing an XKS-S8110 SDI Input Connector
a)
NMI/ST2110
Board in slot 1.
This allows you to physically connect specific output
connectors to dedicated inputs and then select a signal
from an output connector as an input.
For details about dedicated input settings, see "Setting
Dedicated Inputs" (page 435).
Notes
• Dedicated inputs are not supported on the XVS-9000/
7000/6000.
• Only output connectors on an XKS-S8165 SDI Output
Connector Board can be used for dedicated inputs.
The following output connectors can be connected.
- Format converter output connectors 1 to 16
- Spare connectors 1 to 4
- Multi viewer output connectors 1 to 8
- Output connectors 49 to 52
Input signal format conversion
The following format converters can be used.
Internal format converter: Configurable when an XKS-
8460 Format Converter Board is installed (see
page 436).
Input format converter: Configurable when an XKS-
S8111 SDI Input and FC Connector Board or XKS-
S8112/XKS-S9112 12G-SDI Input Board is installed
(see page 439).
Note
On the XVS-9000, internal format converters are not
available.
434
Setting number
1
5
9
13
(and so on)