Cg Border Settings - Sony XVS-9000 User Manual

No. Parameter Adjustment
1 Inner Soft Softness of inner edge of border
2 Bound Soft Softness of border boundary
To add a beveled color edge
1
In the <Border Mode> group, press [Beveled Color
Edge].
2
In the <Color Adjust> group, select the edges for
adjustment.
Select [Top], [Left], [Right], or [Bottom]. To adjust all
four edges simultaneously, press [All].
3
Set the following parameters.
No. Parameter Adjustment
1 Luminance Luminance
2 Saturation Saturation
3 Hue Hue
4
If setting the softness of the border, press [Border
Soft], turning it on.
5
Set the following parameters.
No. Parameter Adjustment
1 Inner Soft Softness of inner edge of border
2 Bound Soft Softness of border boundary
Setting the border (device control block)
You can adjust the border width of the top/bottom/left/
right edges in the device control block (trackball).
Note
The [BDR/CROP] button must be assigned to the
operation buttons beforehand in the Setup menu (see
page 404).
1
Enable the resizer as described in steps 1 to 3 in
"Reducing, enlarging, rotating, and moving keys
(device control block)" (page 130).
2
In the M/E-1 >Key1 >Resizer >Border/Crop menu
(1115.1), press [Border], turning it on.
3
In the device control block, press the [BDR/CROP]
button, turning it on amber.
4
Adjust the border width using the trackball or Z-ring.
• Trackball (horizontal rotation): Adjusts the border
width in the X-axis direction (left/right edges).
• Trackball (vertical rotation): Adjusts the border
width in the Y-axis direction (top/bottom edges).
• Z-ring: Adjusts the border width simultaneously in
the X-axis and Y-axis directions.
The target bank and resizer, and the current parameter
and its value, are displayed in the display of the device
control block.
For details about parameter operations, see "Three-
Dimensional Parameter Entry" (page 224).
Notes
• Pressing the [FINE] button, turning it on, enables
fine adjustment of setting values (fine mode).
• Pressing the [X], [Y], or [Z] button, turning it on,
restricts operation to the selected axis.
• For borders, the number of significant digits of the
parameter after the decimal point is two.

CG Border Settings

The resizers of two keys are used for CG border settings.
The combination of key pairs used is fixed (keys 1 and 2,
keys 3 and 4, keys 5 and 6, keys 7 and 8). The setting
operations are performed using keys 1, 3, 5, and 7 only.
You can also change the position and size of the image
embedded in the border.
This section describes making settings using key 1 and key
2 as an example.
Notes
• This setting is available only when the signal format is
3840×2160P, 1080i.
• To change the position and size of the image embedded in
the border, clean mode must be enabled on the target key.
Enabling the CG border settings using key 1 automatically
enables clean mode on both key 1 and key 2.
• Inserting key 1 also inserts key 2 in unison. Selecting/
releasing key 1 in a next transition also selects/releases
key 2 in unison. Inserting/removing key 2 only and
transition operations using key 2 only are not possible.
• When a CG border is set, key 1 has the following
limitations.
- Dual resizer effects are not supported.
- Resizer border and crop settings are disabled.
- The target of resizer mosaic and defocus settings is
fixed to the video signal only.
• A CG border cannot be set using key 1 if the state of key
2 is any of the following.
- If key 2 is currently inserted or used in a transition.
- When key 2 is selected in a next transition.
- When the resizer of key 2 is enabled.
- When DME wipe is selected for the transition type for
key 2.
133