Sony XVS-9000 User Manual page 111

- Key delegation buttons in the memory recall
section on the Flexi Pad control block (key
operation mode)
• You can assign a key source bus delegation button to
the 1st row or 2nd row of the AUX bus control block
(AUX bus operation mode) in the Setup menu (see
page 410).
To select a video signal assigned to a cross-point
button
Set the operation mode that allows you to select both a key
signal and a video signal using the [KEY] button in the
Setup menu (see page 422).
This allows you to select a key signal and video signal
using the following methods.
• To select a key signal on the cross-point control block in
free assign mode or key/AUX bus delegation mode,
press the [KEY] button on the cross-point pad, turning it
on, and select a key source signal.
• To select a video signal on the cross-point control block
in free assign mode or key/AUX bus delegation mode,
press the [KEY] button on the cross-point pad, turning it
off, and select a key source signal.
Note
When a key source bus delegation button is assigned on the
AUX bus control block (AUX bus operation mode), you
can perform the operation using the [KEY] button on the
cross-point pad.
When a cross-point button on the 3rd/4th row is pressed
while pressing the [KEY] button, the key signal is selected.
When a cross-point button on the 3rd/4th row is pressed
without pressing the [KEY] button, the video signal is
selected.
To select a key source in the menu
1
In the M/E-1 >Key1 >Type menu (1111), press [Key
Bus] in the <Key Fill> group.
2
Press [Signal Select].
The Signal Select menu (1111.3) appears.
3
In the <Target> group, press [Source].
4
In the <Key Source> group, specify the key source
selection mode (Self, Auto Select, or Split).
For details, refer to step 5 in "Selecting the key fill and
key source" (page 110).
5
If [Split] is selected in step 4, select a key source signal
from the list on the right.
6
In the <Assign> group, select the video signal or key
signal from the V/K pair to assign to the key source.
Video: V/K pair video signal
Key: V/K pair key signal
7
Press [Set Xpt].
To select a key fill in the menu
1
In the M/E-1 >Key1 >Type menu (1111), press [Key
Bus] in the <Key Fill> group.
2
Press [Signal Select].
The Signal Select menu (1111.3) appears.
3
In the <Target> group, press [Fill].
4
Select the fill signal from the list on the right.
5
Press [Set Xpt].
Carrying out a color mix for key fill
When [Matte] is selected for key fill, you can use an
independent key transition wipe pattern or dedicated
pattern to combine color 1 and color 2.
1
In the M/E-1 >Key1 >Type menu (1111), press
[Matte] in the <Key Fill> group.
2
Press [Matte Adjust].
The Matte Adjust menu (1111.2) appears.
3
In the <Fill Matte> group, press [Mix Color].
4
Set the following parameters.
No. Parameter Adjustment
1 Size
2 Soft
5
In the <Mix Pattern> group, select the mixing pattern.
Key Wipe: Mix using the wipe pattern selected for an
independent key transition.
Pressing [Pattern Select] opens the M/E-1 >Key1
>Transition/Video Process >Wipe Adjust
>Pattern Select menu (1117.2), allowing you to
select a pattern. Pressing [Pattern Adjust] opens
the M/E-1 >Key1 >Transition/Video Process
>Wipe Adjust menu (1117.1), allowing you to
adjust the pattern.
Key Edge Pattern: Combine using a dedicated color
mix wipe pattern for key edge fill.
Pressing [Pattern Select] opens the M/E-1 >Key1
>Edge >Matte Adjust >Mix Ptn Select menu
(1112.2), allowing you to select a pattern. Pressing
[Pattern Adjust] opens the M/E-1 >Key1 >Edge
111
Pattern size
Degree of softness of pattern edge