Creating And Saving A Master Timeline (Menu) - Sony XVS-9000 User Manual

Notes
• It is not possible to undo a master timeline save.
• Saving the master timeline does not carry out a save of
effects. Save the effects for each region first, then carry
out the master timeline save.
Modifying a master timeline
This section describes changing the M/E-1 register from
Effect 5 to Effect 10 as an example.
Example: Master timeline register information before and
after modification
Region Register
Before
modification
M/E-1 Effect 5
P/P Effect 5
1
Recall the master timeline register you want to change
(see page 303)
.
This simultaneously recalls M/E-1 register 5 and P/P
register 5, and the [M/E1] and [P/P] region selection
buttons light.
2
Press the region selection button [MASTR], turning it
off.
3
Turn on only the button for the region you want to
change ([M/E1]), and recall the desired register (Effect
10).
This recalls M/E-1 register 10, while on P/P register 5
remains selected.
4
Press the buttons for the regions you want to save on
the master timeline ([M/E1] and [P/P]), turning them
on.
5
Press the region selection button [MASTR], turning it
on.
The display shows the last recalled master timeline
register number.
6
Press the [STORE] button, turning it on.
7
Use the numeric keypad buttons to enter the number of
the register in which you want to save the master
timeline, and press the [ENTER] button.
This saves M/E-1 register 10 and P/P register 5 in the
master timeline register.
Checking the regions saved on a master
timeline
For example in the course of changing a master timeline,
you can check which regions are saved in the register.
With the [MASTR] button lit, hold down the [STORE]
button.
While the [STORE] button is pressed, the region selection
button for the saved region lights amber.
Creating and Saving a Master
Timeline (Menu)
1
After modification
Effect 10
Effect 5
2
3
4
5
319
Open the Effect >Master Timeline >Store menu
(6211).
The status area shows the master timeline register
names, register lock status, register number for each
region, and so on.
Switch the region display as required.
Press the button corresponding to the region you want
to display.
M/E: M/E-1 ("ME1"), M/E-2 ("ME2"), M/E-3
("ME3"), M/E-4 ("ME4"), M/E-5 ("ME5")
P/P: PGM/PST ("P/P")
User: User1 ("USR1"), User2 ("USR2"), User3
("USR3"), User4 ("USR4"), User5 ("USR5"),
User6 ("USR6"), User7 ("USR7"), User8
("USR8")
DME: DME ch1 ("DME1"), ch2 ("DME2"), ch3
("DME3"), ch4 ("DME4")
DEV1-8: Device1 ("DEV1"), Device2 ("DEV2"),
Device3 ("DEV3"), Device4 ("DEV4"), Device5
("DEV5"), Device6 ("DEV6"), Device7
("DEV7"), Device8 ("DEV8")
DEV9-12: Device9 ("DEV9"), Device10 ("DEV10"),
Device11 ("DEV11"), Device12 ("DEV12")
Misc: P-Bus ("PBUS"), GPI ("GPI"), Macro
("MCRO")
In the status area, select the target master timeline
register to set.
Press [Edit].
The Edit menu (6211.1) appears.
You can also use the [Master Reg] parameter to select
the master timeline register in this menu.
The status area shows the information for the selected
master timeline register and the region selection
buttons.
Press a region selection button to select a region.
You can select more than one region.