Applied Settings - Omron RX2 Series User Manual

Applied Settings

High-function General-purpose Inverter RX2 Series User's Manual
This chapter explains the settings of the applied functions.
The parameter number structure is indicated below.
This chapter explains how to set the first setting. For the second setting, follow the
same procedure. The setting value and operation are common.
AA 1 01
In-Group Number
-: Always enabled in both the first setting and second setting
1: Enabled in the first setting when the [SET] terminal function is OFF
2: Enabled in the second setting when the [SET] terminal function is ON
Parameter Group
The function assigned to In/Output terminals is indicated as a combination of three dig-
its numbers and alphabets, like "023[F-OP]." For more details of the functions, refer to
the <List of input terminal functions> on page C-44 and the <List of output terminal
functions> on page C-49.
8-1 PID Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
8-1-1 Function Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
8-1-2 PID Parameter and Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
8-1-3 PID Soft-start Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19
8-1-4 PID Sleep Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21
8-1-5 PID2/PID3/PID4 Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-24
8-1-6 PID Signal Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-33
8-1-7 PID Unit Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-36
8-2 Tripless Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-40
8-2-1 Overload Limit Level Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-40
8-2-2 Overcurrent Suppression Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-42
8-2-3 Overvoltage Suppression Function During Deceleration . . . . . . . . . . . . . . . 8-44
8-2-4 Overexcitation Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-47
8-2-5 Regenerative Braking Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-50
8-2-6 Restart during Power Interruption/Undervoltage . . . . . . . . . . . . . . . . . . . . . 8-52
8-2-7 Restart on Overvoltage/Overcurrent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-58
8-2-8 Non-stop on Momentary Power Interruption . . . . . . . . . . . . . . . . . . . . . . . . . 8-63
8-3 Protective Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-69
8-3-1 Input Power Supply Phase Loss Protection . . . . . . . . . . . . . . . . . . . . . . . . . 8-69
8
8 - 1