Omron RX2 Series User Manual page 914

Appendices C Table of Parameters
Parameter Mode (Code U)
Codes that
can be
Code changed
during
operation
Password input for display
UA-01 -
selection
UA-02 - Soft-lock password input
UA-10 - Display restriction selection
Accumulation input power moni-
UA-12 ○
tor clear
Display gain for Accumulation
UA-13 ○
input power monitor
Accumulation output power
UA-14 ○
monitor clear
Display gain for Accumulation
UA-15 ○
output power monitor
UA-16 ○ Soft-lock selection
UA-17 ○ Soft-lock target selection
UA-18 - Data R/W selection
UA-19 - Low battery warning enable
Action selection at Keypad dis-
UA-20 -
connection
2nd-motor parameter display
UA-21 -
selection
Option parameter display selec-
UA-22 -
tion
User parameter auto setting
UA-30 -
function enable
UA-31 ○ User parameter 1 selection
UA-32 ○ User parameter 2 selection
UA-33 ○ User parameter 3 selection
UA-34 ○ User parameter 4 selection
UA-35 ○ User parameter 5 selection
UA-36 ○ User parameter 6 selection
UA-37 ○ User parameter 7 selection
UA-38 ○ User parameter 8 selection
UA-39 ○ User parameter 9 selection
UA-40 ○ User parameter 10 selection
UA-41 ○ User parameter 11 selection
UA-42 ○ User parameter 12 selection
UA-43 ○ User parameter 13 selection
UA-44 ○ User parameter 14 selection
UA-45 ○ User parameter 15 selection
UA-46 ○ User parameter 16 selection
UA-47 ○ User parameter 17 selection
UA-48 ○ User parameter 18 selection
UA-49 ○ User parameter 19 selection
UA-50 ○ User parameter 20 selection
UA-51 ○ User parameter 21 selection
UA-52 ○ User parameter 22 selection
UA-53 ○ User parameter 23 selection
UA-54 ○ User parameter 24 selection
UA-55 ○ User parameter 25 selection
UA-56 ○ User parameter 26 selection
UA-57 ○ User parameter 27 selection
C - 66
Name
-
-
00 (Full display)/01 (By function)/02 (User setting)/
03 (Conveyor display)/04 (Only monitor display)
00 (Disabled)/01 (Clear)
1 to 1000
00 (Disabled)/01 (Clear)
1 to 1000
00 ([SFT] terminal)/01 (Always enabled)
00 (All data cannot be changed)/
01 (Data other than set frequency cannot be changed)
00 (R/W enabled)/01 (R/W disabled)
00 (Disabled)/01 (Warning)/02 (Error)
00 (Error)/01 (Error after deceleration stop)/02 (Ignore)/
03 (Free run)/04 (Deceleration stop)
00 (Not display/01 (Display)
00 (Not display/01 (Display)
00 (Disabled)/01 (Enabled)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
no/***** (select a parameter)
High-function General-purpose Inverter RX2 Series User's Manual
Data range
Initial
Note
value
0000
0000
00
00
1
00
1
00
00
00
00
02
01
01
00
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no