Icom ID-51A Advanced Instructions page 2

Previous view
INTRODUCTION
About these Advanced Instructions (PDF format)
These Advanced Instructions describe the details of the ID-51A/E features. This PDF formatted manual provides
you with convenient functions, as follows.
Move to the previously read page.
Click
each page, to move back to the previ-
ously read page.
Previous view
15
REPEATER AND DUPLEX OPERATIONS
� Duplex operation
Shows the location of keys
When the cursor is moved over a term with a red
The Duplex operation shifts the transmit frequency
underline, a red circle appears around the ap-
up or down from the receive frequency by an offset
propriate key(s) on the figure of the transceiver.
amount.
D Setting the frequency offset
Push [V/MHz]
q
Push [MENU]
w
Push D-pad(
e
TONE..."), and then push D-pad(Ent).
D-pad
Example: When the cursor is moved over
(Ent)
[V/MHz]
( )
red circle appears around the ap-
Push D-pad(
r
propriate key(s).
push D-pad(Ent).
Rotate [DIAL] to set the frequency offset to be-
t
tween 0.000.00 and 59.99500 MHz, and then push
D-pad(Ent).
The
setting the frequency offset.
[V/MHz]
below.
TS*
* The frequency changes according to the preset tuning
Move to the page, if clicked.
steps. (p. 5-6)
Push [MENU]
y
(p. 15-5)
To reset to the default value.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the
Push [QUICK]
United Kingdom, Germany, France, Spain, Russia and/or other countries.
push D-pad(Ent) to reset to the default value.
Adobe and Adobe Reader are registered trademark of Adobe Systems Incorporated.
All other products or brands are registered trademarks or trademarks of their respective holders.
NOTE:
• The frequency offset cannot be changed in the DR
mode.
• The Auto repeater function uses the preset fre-
Previous view
at the left top on an
Previous view
Previous view
15
� Duplex operation
The Duplex operation shifts the transmit frequency
up or down from the receive frequency by an offset
amount.
D Setting the frequency offset
Push [V/MHz]
q
Push [MENU]
w
Push D-pad(
e
TONE..."), and then push D-pad(Ent).
to select the VFO mode.
D-pad
.
�) to select the root item ("DUP/
Push D-pad(
r
push D-pad(Ent).
Rotate [DIAL] to set the frequency offset to be-
t
in the description, a
tween 0.000.00 and 59.99500 MHz, and then push
D-pad(Ent).
�) to select the "Offset Freq," and then
The
setting the frequency offset.
below.
(Setting example: 1.000.00 MHz)
tuning step in the VFO mode is used when
* The frequency changes according to the preset tuning
toggles the tuning digit, as shown
Push [MENU]
y
1 MHz 10 MHz
to exit the [MENU] screen.
[DIAL]
To reset to the default value.
Push [QUICK]
push D-pad(Ent) to reset to the default value.
NOTE:
in step t as described above, then
• The frequency offset cannot be changed in the DR
• The Auto repeater function uses the preset fre-
15
REPEATER AND DUPLEX OPERATIONS
� Duplex operation
The Duplex operation shifts the transmit frequency
up or down from the receive frequency by an offset
amount.
D Setting the frequency offset
Push [V/MHz] to select the VFO mode.
q
Shows a term description
Push [MENU] .
w
Push D-pad( �) to select the root item ("DUP/
e
When the mouse cursor is moved over a term which
TONE..."), and then push D-pad(Ent).
is highlighted in yellow, the description of the term is
D-pad
displayed.
(Ent)
( )
Push D-pad( �) to select the "Offset Freq," and then
r
push D-pad(Ent).
Rotate [DIAL] to set the frequency offset to be-
t
REPEATER AND DUPLEX OPERATIONS
tween 0.000.00 and 59.99500 MHz, and then push
D-pad(Ent). (Setting example: 1.000.00 MHz)
The tuning step in the VFO mode is used when
setting the frequency offset.
[V/MHz] toggles the tuning digit, as shown
below.
TS* 1 MHz 10 MHz
* The frequency changes according to the preset tuning Previous view
steps. (p. 5-6)
15
REPEATER AND DUPLEX OPERATIONS
Push [MENU] to exit the [MENU] screen.
y
� Duplex operation
to select the VFO mode.
The Duplex operation shifts the transmit frequency
.
up or down from the receive frequency by an offset
amount.
�) to select the root item ("DUP/
D Setting the frequency offset
Push [V/MHz] to select the VFO mode.
q
Push [MENU] .
w
Push D-pad( �) to select the root item ("DUP/
e
TONE..."), and then push D-pad(Ent).
(Ent)
D-pad
(Ent)
( )
( )
r Push D-pad( �) to select the "Offset Freq," and then
push D-pad(Ent).
�) to select the "Offset Freq," and then
t Rotate [DIAL] to set the frequency offset to be-
tween 0.000.00 and 59.99500 MHz, and then push
D-pad(Ent). (Setting example: 1.000.00 MHz)
The tuning step in the VFO mode is used when
setting the frequency offset.
[V/MHz]
below.
TS* 1 MHz
(Setting example: 1.000.00 MHz)
To reset to the default value.
* The frequency changes according to the preset tuning
tuning step in the VFO mode is used when
steps. (p. 5-6)
Push [MENU] to exit the [MENU] screen.
y
Push [QUICK] in step t as described above, then
push D-pad(Ent) to reset to the default value.
[V/MHz] toggles the tuning digit, as shown
TS* 1 MHz 10 MHz
NOTE:
• The frequency offset cannot be changed in the DR
steps. (p. 5-6)
mode.
to exit the [MENU] screen.
To reset to the default value.
• The Auto repeater function uses the preset fre-
Push [QUICK] in step t as described above, then
quency offset. Depending on the frequency offset
push D-pad(Ent) to reset to the default value.
[DIAL]
value, the off band indication, "OFF," appears on
NOTE:
the display when [PTT] is pushed. (p. 15-5)
• The frequency offset cannot be changed in the DR
mode.
• The Auto repeater function uses the preset fre-
quency offset. Depending on the frequency offset
value, the off band indication, "OFF," appears on
the display when [PTT] is pushed. (p. 15-5)
The screen shots at the right column, correspond
to the operating instructions and procedures
shows both setting and operating example.
in step t as described above, then
mode.
quency offset. Depending on the frequency offset
i
value, the off band indication, "OFF," appears on
the display when [PTT] is pushed. (p. 15-5)
[DIAL]
toggles the tuning digit, as shown
10 MHz
[DIAL]
The current frequency
offset
Rotate [DIAL], then
push D-pad(Ent).
15-4
15-4
Push [QUICK]
Push D-pad(Ent)
Th
off
Ro
pu
The current frequency
offset
Pu
Rotate [DIAL], then
push D-pad(Ent).
The current f
offset
Rotate [DIAL
Pu
push D-pad(
Push [QUICK]
Push D-pad(Ent)
Th
The current frequency off
offset
Push [QUIC
Push D-pad(