Information List; En100-Module; Description - Siemens 7SC80 Manual

Addr. Parameter
6023 S3: x'
6024 S3: x'
6025 S3: Line angle
6026 S3: Line length
6027 S3: Line length

Information List

2.1.6.4
No. Information
126 ProtON/OFF
356 >Manual Close
420 >Opened Ctrl 2
421 >Opened Ctrl 3
422 >Closed Ctrl 2
423 >Closed Ctrl 3
424 Open Ctrl 2
425 Close Ctrl 2
426 Open Ctrl 3
427 Close Ctrl 3
501 Relay PICKUP
511 Relay TRIP
533 Ia =
534 Ib =
535 Ic =
561 Man.Clos.Detect
2720 >Enable ANSI#-2
4601 >52-a
4602 >52-b
6011 >Opened Ctrl 1
6012 >Closed Ctrl 1
6013 Open Ctrl 1
6014 Close Ctrl 1
16019 >52 Wear start
16020 52 WearSet.fail
16027 52WL.blk I PErr
16028 52WL.blk n PErr

EN100-Module

2.1.7
2.1.7.1

Description

The EN100-Module enables integration of the 7SC80 in 100-Mbit communication networks in control and
automation systems with the protocols according to IEC 61850 standard. This standard permits uniform
communication of the devices without gateways and protocol converters. Even when installed in heteroge-
neous environments, SIPROTEC 4 relays therefore provide for open and interoperable operation. Parallel to the
SIPROTEC Compact, 7SC80, Manual
E50417-G1140-C486-A8, Edition 07.2017
C Setting Options
1A 0.0050 .. 15.0000 Ω/mi
5A 0.0010 .. 3.0000 Ω/mi
1A 0.0050 .. 9.5000 Ω/km
5A 0.0010 .. 1.9000 Ω/km
10 .. 89 °
0.1 .. 650.0 Miles
0.1 .. 1000.0 km
Type of Comments
Informa-
tion
IntSP Protection ON/OFF (via system port)
SP >Manual close signal
SP >Opened Control device 2
SP >Opened Control device 3
SP >Closed Control device 2
SP >Closed Control device 3
OUT Open control device 2
OUT Close control device 2
OUT Open control device 3
OUT Close control device 3
OUT Relay PICKUP
OUT Relay GENERAL TRIP command
VI Primary fault current Ia
VI Primary fault current Ib
VI Primary fault current Ic
OUT Manual close signal detected
SP >Enable 50/67-(N)-2 (override 79 blk)
SP >52-a contact (OPEN, if bkr is open)
SP >52-b contact (OPEN, if bkr is closed)
SP >Opened Control device 1
SP >Closed Control device 1
OUT Open control device 1
OUT Close control device 1
SP >52 Breaker Wear Start Criteria
OUT 52 Wear blocked by Time Setting Failure
OUT 52 Breaker Wear Logic blk Ir-CB>=Isc-CB
OUT 52 Breaker W.Log.blk SwCyc.Isc>=SwCyc.Ir
Default Setting Comments
0.2420 Ω/mi S3: feeder reactance per
mile: x'
0.0484 Ω/mi
0.1500 Ω/km S3: feeder reactance per
km: x'
0.0300 Ω/km
85 ° S3: Line angle
62.1 Miles S3: Line length in miles
100.0 km S3: Line length in kilometer
Functions
2.1 General
69