Agilent Technologies 8753ES Option 011 Service Manual page 479

Index
equipment
cavity oscillator frequency
,
adjustment 3-25
display intensity correction
constants adjustment
EEPROM backup disk
,
procedure 3-33
fractional-N
frequency range adjustment
3-39
spur avoidance and FM
sideband adjustment
frequency accuracy adjustment
3-42
IF amplifier correction
constants adjustment
,
required 1-2
RF output power correction
constants adjustment
sampler magnitude adjustment
3-19
source spur avoidance tracking
,
adjustment 3-50
, ,
error messages 5-17 10-44
,
accessories 4-19
,
phase lock loop 7-6
,
receiver 4-18
,
receiver failure 8-4
, , ,
error terms 9-5 11-2 11-3
,
descriptions 11-9
directivity (EDF and EDR)
,
inspection 11-8
isolation (crosstalk EXF and
,
EXR) 11-12
load match (ELF and ELR)
11-13
reflection tracking (ERF and
,
ERR) 11-11
source match (ESF and ESR)
11-10
transmission tracking (ETF and
,
ETR) 11-14
external
,
reference input 10-37
,
source mode 12-24
source mode frequency range
,
test 2-14
,
test sets 12-26
,
tests 10-10
F
failure
,
A1/A2 front panel 6-12
A11 phase lock and A3 source
,
check 7-8
error messages for receiver
,
GPIB 6-19
Index
,
key stuck 6-13
phase lock error
RF power from source
,
fan 5-19
, ,
6-7 assembly 14-42
,
speeds 5-19
,
voltages 5-19
faulty assembly
, ,
faulty data 4-18
firmware revision softkey
FM Coil plot with 3 point sweep
,
3-47 7-29
,
FN LO at A12 check
FN LO waveform at A12J1
formatting conventions
,
3-16 FRACN TUNE mode HI OUT
,
signal 7-27
fractional-N
, ,
3-11 check 7-20
,
frequency range adjustment
3-39
,
sequence 3-53
spur avoidance and FM
sideband adjustment
,
sequence 3-53
frequency
accuracy adjustment
,
counter 10-20
output in SRC tune mode
range and accuracy test
,
11-9 range of fractional-N
adjustment
range, external source
response (ratio) test
, ,
response test
front panel
,
assembly 13-18
,
key codes 6-13
, ,
LEDs 4-5
troubleshooting
G
GPIB
,
addresses 4-8
,
failures 6-19
service mnemonic definitions
10-42
,
system check
graphics processor
H
,
H MB line 7-24
,
hardware 13-26
13-30
,
bottom view 13-28
,
8-4
harmonic analysis
,
harmonics test
HI OUT signal in FRACN TUNE
,
7-6 mode
,
7-5 high band REF signal
high quality comb tooth at 3 GHz
7-26
high stability frequency reference
(option 1D5) assembly
,
5-11 high/low band transition
adjustment
,
10-41 adjustment sequence
,
how to
adjust
,
7-16 ADC offset correction
,
7-16
,
1-iv analog bus correction
cavity oscillator frequency
fractional-N frequency range
,
fractional-N spur avoidance
frequency accuracy
,
3-47 high/low band transition
IF amplifier correction
,
3-42 option numbers correction
,
7-9 RF output power correction
,
2-4
sampler magnitude correction
,
3-39
,
2-14 serial number correction
,
2-27
2-23 source default correction
, ,
14-8 14-10 source pretune correction
source pretune default
,
6-12
source spur avoidance
the analyzer
the analyzer using sequences
backup the EEPROM disk
,
check display intensity
initialize EEPROMs
4-8
load sequences from disk
,
14-35
position the A9 switch
retrieve correction constant data
, , ,
13-28 13-29
set up
high/low band transition
,
12-23
,
2-66 2-70
,
7-27
,
7-15
,
14-40
,
3-45
,
3-53
,
constants 3-18
,
constants 3-9
,
correction constants 3-25
,
3-39
,
and FM sideband 3-47
,
3-42
,
3-45
,
constants 3-16
,
constants 3-31
,
constants 3-11
,
constants 3-19
,
constants 3-30
,
constants 3-7
,
constants 3-10
,
correction constants 3-8
,
tracking 3-50
,
3-1
3-53
,
3-33
,
6-7
,
3-32
,
3-53
,
3-6
from EEPROM backup disk
3-34
,
adjustments 3-54
Index-3
,
,
,