Danfoss ADAP-KOOL Drive Programming Manual page 33

®
ADAP-KOOL Drive Programming Guide
3.2.3 0-1* Set-up Operations
Define and control the individual parameter set-ups.
The frequency converter has four parameter setups that can be programmed independently of each other. This makes the frequency converter very
flexible and able to meet the requirements of many different ADAP-KOOL system control schemes often saving the cost of external control equipment.
For example these can be used to program the frequency converter to operate according to one control scheme in one setup (e.g. daytime operation)
and another control scheme in another setup (e.g. night set back). Alternatively they can be used by an AHU or packaged unit OEM to identically program
all their factory fitted frequency converters for different equipment models within a range to have the same parameters and then during production/
commissioning simply select a specific setup depending on which model within that range the frequency converter is installed on.
The active setup (i.e. the setup in which the frequency converter is currently operating) can be selected in parameter 0-10 and is displayed in the LCP.
Using Multi set-up it is possible to switch between set-ups with the frequency converter running or stopped, via digital input or serial communication
commands (e.g. for night set back). If it is necessary to change setups whilst running, ensure parameter 0-12 is programmed as required. For the majority
of ADAP-KOOL applications it will not be necessary to program parameter 0-12 even if change of set up whilst running is required, but for very complex
applications, using the full flexibility of the multiple setups, it may be required. Using parameter 0-11 it is possible to edit parameters within any of the
setups whilst continuing the frequency converter operation in its Active Setup which can be a different setup to that being edited. Using parameter 0-51
it is possible to copy parameter settings between the set-ups to enable quicker commissioning if similar parameter settings are required in different set-
ups.
0-10 Active Set-up
Option:
[0] Factory setup
[1] * Set-up 1
[2] Set-up 2
[3] Set-up 3
[4] Set-up 4
[9] Multi Set-up
0-11 Programming Set-up
Option:
[0] Factory setup
[1] Set-up 1
[2] Set-up 2
[3] Set-up 3
[4] Set-up 4
[9] * Active Set-up
Function:
Select the set-up in which the frequency converter is to operate.
Use par.0-51 Set-up Copy to copy a set-up to one or all other set-ups. To avoid conflicting settings
of the same parameter within two different set-ups, link the set-ups together using par.0-12
Set-up Linked to
. Stop the frequency converter before switching between set-ups where parameters
marked 'not changeable during operation' have different values.
Parameters which are 'not changeable during operation' are marked FALSE in the parameter lists in
Parameter Lists
the section
Cannot be changed. It contains the Danfoss data set, and can be used as a data source when
returning the other set-ups to a known state.
Set-up 1 Set-up 4
[1] to [4] are the four separate parameter set-ups within which all parameters
can be programmed.
Is used for remote selection of set-ups using digital inputs and the serial communication port. This
set-up uses the settings from par.0-12
Function:
Select the set-up to be edited (i.e. programmed) during operation; either the active set-up or one
of the inactive set-ups. The set-up number being edited is displayed in the LCP in (brackets).
cannot be edited but it is useful as a data source to return the other set-ups to a known state.
Set-up 1 Set-up 4
[1] to [4] can be edited freely during operation, independently of the active set-
up.
(i.e. the set-up in which the frequency converter is operating) can also be edited during operation.
Editing parameters in the chosen setup would normally be done from the LCP but it is also possible
from any of the serial communication ports.
MG.11.N1.02 - VLT ® is a registered Danfoss trademark
3 Parameter Description
This Set-up Linked to .
3
This
33