Siemens SIMOVERT MASTERDRIVES Manual page 1121

Parameter Description
P032* BICO parameter for selecting connectors which are to be
S.Disp Conn displayed in visualization parameter r033 in [%]. The
connector numbers shown in the respective index are
32 displayed in the same index of parameter r033.
In function diagram:
30.1
r033 Visualization parameter for displaying the connectors
Display Conn given in P032. The connnectors displayed in the
respective index have been selected in the same index of
33 parameter P032. A connector value of 4000 H or 4000
0000 H is shown at 100 %.
In function diagram:
30.2
P034* BICO parameter for selecting connectors which contain a
S.DispVoltsConn voltage and are to be displayed in visualization parameter
r035 in [V]. The connector numbers entered in the
34 respective index are displayed in the same index of
parameter r035.
In function diagram:
30.4
r035 Visualization parameter for displaying connectors given in
Disp Volts Conn P034 in [V]. The connectors displayed in the respective
index have been selected in the same index of parameter
35 P034. The normalization is specified in P351. The
following method of calculation must be used:
r035 = P351 xConnector Value in [%]/100%.
In function diagram:
30.5
P036* BICO parameter for selecting connectors which contain a
S.DispAmpsConn current and are to be displayed in visualization parameter
r037 in [A]. The connector numbers entered in the
36 respective index are displayed in the same index of
parameter r037.
In function diagram:
30.4
r037 Visualization parameter for the display of connectors
Disp Amps Conn given in P036 in [A]. The connectors displayed in the
respective index have been selected in the same index of
37 parameter P036. The normalization is specified in P350.
The following method of calculation must be used:
r037 = P350 xConnector Value in [%]/100%.
In function diagram:
30.5
P038* BICO parameter for selecting connectors which contain a
S.DispTorqConn torque and are to be displayed in visualization parameter
r039 in [Nm]. The connector numbers entered in the
38 respective index are displayed in the same index of
parameter r039.
r039 Visualization parameter for the display of connectors
Disp Torq Conn given in P038 in [Nm]. The connectors displayed in the
respective index have been selected in the same index of
39 parameter P038. The normalization is specified in P354.
The following method of calculation must be used:
r039 = P354 x Connector Value in [%]/100%.
Siemens AG 6SE7087-6QX70 (Edition AG)
SIMOVERT MASTERDRIVES Compendium Motion Control
Data Read/write
index1: 0 Menus:
Unit: - - Parameter menu
Indices: 5 + General parameters
Type: L2 ,K - Upread/free access
,K Changeable in:
- Ready to switch on
- Operation enabled
Dec.Plc.: 3 Menus:
Unit: % - Parameter menu
Indices: 5 + General parameters
Type: I4 - Upread/free access
index1: 0 Menus:
Unit: - - Parameter menu
Indices: 5 + General parameters
Type: L2 ,K - Upread/free access
Changeable in:
- Ready to switch on
- Operation enabled
Dec.Plc.: 1 Menus:
Unit: V - Parameter menu
Indices: 5 + General parameters
Type: I4 - Upread/free access
index1: 0 Menus:
Unit: - - Parameter menu
Indices: 5 + General parameters
Type: L2 ,K - Upread/free access
Changeable in:
- Ready to switch on
- Operation enabled
Dec.Plc.: 2 Menus:
Unit: A - Parameter menu
Indices: 5 + General parameters
Type: I4 - Upread/free access
index1: 0 Menus:
Unit: - - Parameter menu
Indices: 5 + General parameters
Type: L2 ,K - Upread/free access
Changeable in:
- Ready to switch on
- Operation enabled
Dec.Plc.: 2 Menus:
Unit: Nm - Parameter menu
Indices: 5 + General parameters
Type: I4 - Upread/free access
4