Siemens SIMOVERT MASTERDRIVES Manual page 1338

Parameter Description
U719* [FD784b] Input binectors for axial winders
SrcAxialWinderB
Index 1: Diameter calculator
2719 Hold diameter, the last calculated diameter value is frozen
Index 2: Diameter calculator
Set diameter, adopts the setting value present at U717.6
Setting has higher priority than holding.
Index 3: Diameter calculator
Changing over the type of winding from top to bottom
Index 4: Moment of inertia
Changing over the type of winding from top to bottom
U720 The automatic record stored in the EEPROM is displayed
AutomaticRecord on parameters.
The automatic record consists of the following data:
2720
1. Program number / continuation number / record number
2. Validity bits of functions or values
3. 1...4 G-function
4. Position
5. Speed
6. 1...3 M-function / D-number
U721 The automatic record stored in the EEPROM is displayed
AutomaticRecord on parameters.
The automatic record consists of the following data:
2721
1. Program number / continuation number / record number
2. Validity bits of functions or values
3. 1...4 G-function
4. Position
5. Speed
6. 1...3 M-function / D-number
U722 The automatic record stored in the EEPROM is displayed
AutomaticRecord on parameters.
The automatic record consists of the following data:
2722
1. Program number / continuation number / record number
2. Validity bits of functions or values
3. 1...4 G-function
4. Position
5. Speed
6. 1...3 M-function / D-number
U723 The automatic record stored in the EEPROM is displayed
AutomaticRecord on parameters.
The automatic record consists of the following data:
2723
1. Program number / continuation number / record number
2. Validity bits of functions or values
3. 1...4 G-function
4. Position
5. Speed
6. 1...3 M-function / D-number
U724 The automatic record stored in the EEPROM is displayed
AutomaticRecord on parameters.
The automatic record consists of the following data:
2724
1. Program number / continuation number / record number
2. Validity bits of functions or values
3. 1...4 G-function
4. Position
5. Speed
6. 1...3 M-function / D-number
Siemens AG 6SE7087-6QX70 (Edition AG)
SIMOVERT MASTERDRIVES Compendium Motion Control
Data Read/write
index1: 0 Menus:
Unit: - - Parameter menu
Indices: 4 - Upread/free access
Type: L2 ,B Changeable in:
- Ready to switch on
- Operation enabled
index1: 0 Menus:
Min: - - Parameter menu
2147483647 + Technology
Max: + Positioning
2147483647 - Upread/free access
Unit: - Changeable in:
Indices: 6 - Ready to switch on
Type: I4 - Operation enabled
index1: 0 Menus:
Min: - - Parameter menu
2147483647 + Technology
Max: + Positioning
2147483647 - Upread/free access
Unit: - Changeable in:
Indices: 6 - Ready to switch on
Type: I4 - Operation enabled
index1: 0 Menus:
Min: - - Parameter menu
2147483647 + Technology
Max: + Positioning
2147483647 - Upread/free access
Unit: - Changeable in:
Indices: 6 - Ready to switch on
Type: I4 - Operation enabled
index1: 0 Menus:
Min: - - Parameter menu
2147483647 + Technology
Max: + Positioning
2147483647 - Upread/free access
Unit: - Changeable in:
Indices: 6 - Ready to switch on
Type: I4 - Operation enabled
index1: 0 Menus:
Min: - - Parameter menu
2147483647 + Technology
Max: + Positioning
2147483647 - Upread/free access
Unit: - Changeable in:
Indices: 6 - Ready to switch on
Type: I4 - Operation enabled
221