Agilent Technologies 8753ET User Manual page 479

Index
transforming CW time measurements
,
into the frequency domain
forward transform measurements
3-22
transmission measurements in time
,
domain low pass 3-19
interpreting the low pass step
transmission response horizontal
,
axis 3-20
interpreting the low pass step
transmission response vertical
,
axis 3-20
measuring separate transmission
paths through the test device
using low pass impulse mode
3-20
measuring small signal transient
response using low pass step
3-19
transmission measurements using
,
bandpass mode 3-14
interpreting the bandpass
transmission response horizontal
,
axis 3-14
interpreting the bandpass
transmission response vertical
,
axis 3-14
transmission measurements, response
and isolation error correction
transmission measurements, response
,
error correction 6-14
transmission response measurements,
,
making 3-5
,
TRL calibration, performing 6-52
TRL error correction
assigning standards to various TRL
,
classes 6-51
,
label the calibration kit 6-51
,
label the classes 6-51
performing the TRL calibration
,
TRL error-correction 6-50
creating a user-defined TRL calibration
,
kit 6-50
,
TRL options 7-77
,
TRL terminology 7-69
,
TRL* error model 7-69
,
TRL*/LRM* calibration 7-68
fabricating and defining calibration
,
standards for TRL/LRM
,
how TRL*/LRM* works 7-69
improving raw source match and load
match for TRL*/LRM*
,
calibration 7-72
,
isolation 7-70
,
source match and load match
,
TRL calibration procedure 7-73
,
TRL options 7-77
TRL standards, requirements
,
3-22 TRL terminology
,
TRL* error model
TRL*/LRM* two-port calibration
TRM error correction
assigning standards to various TRM
,
classes 6-55
creating a user-defined TRM
calibration kit
labeling the calibration kit
labeling the classes
modifying the standard definitions
6-54
performing the TRM calibration
,
TTL
,
I/O menu 1-110
input decision making
, ,
out menu 1-114
output for controlling peripherals
1-110
tuned receiver mode
in-depth description
test setup, typical
two sources
addressing and configuring
two-port calibration, full
two-port calibration, TRL*/LRM*
two-port error model
,
6-17 type-N connector sex
,
clarifying 6-4
types of error correction
U
uncoupling display markers
understanding
harmonic operation
,
spur avoidance
understanding power ranges
understanding S-parameters
,
6-52
upper stopband parameters
using continuous correction mode
using direct sampler access
configurations
,
noise floor plot
using external calibration
using fast 2-port calibration
using sample-and-sweep correction
,
mode 6-36
7-74
using swept list mode
detecting IF delay
using the parallel port
,
copy mode 7-81
,
GPIO mode 7-81
7-71
V
vector error-correction
verification, performance
,
7-73 verifying performance
7-69 vertical axis
,
7-69 3-22
,
7-57 viewing a single measurement channel
,
6-54 5-12
viewing plot files on a PC
using AmiPro
using Freelance
,
6-54
,
6-55
W
,
6-55
what you can save to a computer
,
what you can save to a floppy disk
what you can save to the analyzer's
,
6-56
internal memory
widening the system bandwidth
windowing
,
1-111
finite impulse width (or rise time)
sidelobes
,
, , ,
2-26 2-28 7-86
,
7-87
,
7-87
,
2-29
,
7-57
,
7-57
,
7-48
,
6-10
,
1-31
,
1-58
5-18
,
7-10
,
7-21
,
1-73
,
6-38
,
5-16
5-17
,
5-12
,
5-12
,
5-9
,
5-10
,
7-81
,
7-8
,
5-5
,
7-66
, , , , ,
3-13 3-14 3-17 3-20
,
,
4-20
,
4-21
,
4-21
,
4-35
,
4-35
,
4-34
,
5-11
,
3-27
,
3-27
,
3-27
Index-11