Agilent Technologies 8753ET User Manual page 472

Index
four-channel display
,
4 Param Displays softkey 1-18
,
Channel Position softkey 1-17
,
customizing 1-17
,
viewing 1-14
,
Freelance, using 4-21
frequency
,
segments, editing 6-34
,
signals, deleting 6-35
,
span, decreasing 5-10
,
span, setting 1-37
frequency bands
,
adding 1-89
,
changing 1-88
,
deleting 1-90
,
setting 1-87
,
frequency drift 5-5
frequency list sweep of 26 points
frequency offset mode operation
frequency offset mode, conversion
,
compression 2-39
frequency offset mode, conversion loss
2-13
,
frequency offset operation 7-87
, ,
frequency range 1-59 7-89
,
frequency range, setting 1-5
frequency range, setting for time domain
,
low pass 3-15
,
frequency response 7-42
frequency response and isolation error
,
corrections 6-17
,
reflection measurements 6-19
,
transmission measurements
frequency response error corrections
6-12
,
receiver calibration 6-15
response error correction for reflection
,
measurements 6-12
response error correction for
transmission measurements
6-14
frequency response of calibration
,
standards 6-6
,
electrical offset 6-6
,
fringe capacitance 6-7
,
fringe capacitance 6-7
,
full two-port calibration 7-57
,
full two-port error correction 6-29
G
,
gain 1-64
gain compression
,
measuring 1-60
,
using linear sweep 1-62
, ,
gating 3-35 7-8
,
selecting gate shape 3-36
,
setting the gate 3-35
Index-4
,
general 8-7
generating files in a loop counter
,
example 1-118
German FTZ emissions requirements
8-8
gosub sequence command
,
GPIB commands 1-124
GPIB operation
,
address menu 7-80
GPIB STATUS indicators
,
local key 7-79
pass control mode
system controller mode
talker/listener mode
using the parallel port
,
GPIO mode 1-110
graphic files
,
2-28 saving measurement results as
,
2-10 grids
moving marker information off the
,
grids 1-26
, ,
group delay 1-47
group delay format
group delay measurements
group delay principles
H
harmonic measurements
,
additional 1-57
,
making 1-56
harmonic operation
accuracy and input power
6-17
coupling power between channels 1
,
, ,
and 2 1-59
dual-channel operation
,
frequency range
single-channel operation
test setup, typical
,
understanding 1-58
,
harmonics, measuring
making harmonic measurements
high dynamic range
,
measurement 2-23
swept RF/IF conversion loss
high dynamic range measurement
2-23
high dynamic range swept RF/IF
conversion loss
measurement parameters for IF range
2-20
power meter calibration over IF range
2-20
power meter calibration over RF range
2-23
receiver calibration over IF range
RF frequency range
high power
configuration one
configuration three
configuration two
,
measurements
horizontal axis
,
1-109
how RF and IF are defined
HPGL
compatible printer
,
7-80 initialization sequence, sending to the
,
7-80 initialization sequence, storing
,
7-80 HPGL compatible printer
,
7-80 HPGL/2 compatible printer
,
7-81
,
7-81
I
IF bandwidth reduction
,
4-44
IF bandwidth, setting segment
IF delay, detecting
IF detection
IF range
measurement parameters
,
7-27
power meter calibration
,
2-34
receiver calibration
,
7-32
IF, defining
imaginary format
improving measurement results
decreasing the sweep rate
decreasing time delay
improving raw source match and load
,
7-88
, ,
1-59 7-89
increase sweep speed
7-89 using fast 2-port calibration
, ,
1-58 7-88 increasing dynamic range
,
1-59 7-89 increasing test port input power
, ,
1-58 7-88 reducing receiver crosstalk
,
7-88 reducing the receiver noise floor
increasing measurement accuracy
,
1-55 connector repeatability
,
1-56 frequency drift
interconnecting cables
performance verification
,
2-20 reference plane and port extensions
,
temperature drift
increasing sweep speed
activating chop sweep mode
,
decreasing the frequency span
reducing the averaging factor
,
reducing the number of measurement
,
setting the auto sweep time mode
,
2-22 setting the sweep type
,
2-22 using external calibration
using swept list mode
,
1-67
,
1-70
,
1-69
,
1-66
, , , ,
3-13 3-14 3-16 3-20
3-23
,
2-7
,
4-19
,
printer 4-24
,
4-23
,
4-23
,
4-9
,
7-37
,
7-19
,
5-10
,
7-7
,
2-20
,
2-20
,
2-22
,
2-7
,
7-32
,
5-7
,
5-8
,
5-8
match for TRL*/LRM* calibration
7-72
,
5-12
,
5-14
,
5-14
,
5-14
,
5-14
,
5-4
,
5-4
,
5-5
,
5-4
,
5-5
5-5
,
5-5
,
5-9
,
5-12
,
5-10
,
5-11
,
points 5-11
,
5-11
,
5-11
,
5-12
,
5-9
,
,
,