Chapter 3 Setup; About Setup Menu - MIMAKI Tx500P-3200DS Operation Manual

Chapter 3 Setup

About Setup menu

On Setup menu, you can set the print conditions to match the media you usually use.
Local <Setup 1>
1340mm
CONSTANT POST 1L
179° C/180° C
TEST PRINT /
MENU REMOTE
CLEANING
 Setup menus at-a-glance
Local <Setup 1> 12:00
1340mm
CONSTANT
179° C/180° C
TEST PRINT /
MENU REMOTE
CLEANING
Setup 1 1/4
Feed Comp. >
DropPos. Correct >
Heater >
Host
Logical Seek
Host
Overprint
<< >>
Setup 1
2/4
Drying Time >
Margin/L 0mm
Margin/R 0mm
Refresh Host
Refresh Left OFF
<< >>
Setup 1 3/4
Drying Fan Standard
Feed Speed >
MAPS4 >
Auto Nozzle Maint. >
Interval Wiping OFF
<< >>
Setup 1 4/4
Head Gap 2.0mm
Setup Reset >
<< >>
3-2
12:00
MENU
Setup >
Maintenance >
Media Reset >
>
Machine Setup
Information >
<< >>
Setup 1 1/4
Feed Comp. >
DropPos. Correct >
Heater >
Host
Logical Seek
Host
Overprint
<< >>
Setup 1
2/4
Drying Time >
Margin/L 0mm
Margin/R 0mm
Refresh Host
Refresh Left OFF
<< >>
Setup 1 3/4
Drying Fan Standard
Feed Speed >
MAPS4 >
Auto Nozzle Maint. >
Interval Wiping OFF
<< >>
Setup 1 4/4
Head Gap 2.0mm
Setup Reset >
<< >>
: Press this to select SETTING menu, or to switch to the
previous screen.
: Press this to use the adjust function.
: Press this to switch to the next screen.
: Use these to select a setting item.
: Press this to confirm a setting, etc..
Setup
● Setup 1
○ Setup 2
Select "SETUP 1 to 4" or "Temporary",
○ Setup 3
and then press the
○ Setup 4
○ Temporary
<< >>
Setup 1 1/4 Setup 1
Feed Comp. > Feed Comp.
DropPos. Correct > DropPos. Correct
Heater > Heater
Host
Logical Seek Logical Seek
Host
Overprint Overprint
<< >> <<
Setup 1 Setup 1
2/4
Drying Time > Drying Time
Margin/L 0mm Margin/L
Margin/R 0mm Margin/R
Refresh Host Refresh
Refresh Left OFF Refresh Left
<< >> <<
Setup 1 3/4 Setup 1
Drying Fan Standard Drying Fan
Feed Speed > Feed Speed
MAPS4 > MAPS4
Auto Nozzle Maint. > Auto Nozzle Maint.
Interval Wiping OFF Interval Wiping
<< >> <<
Setup 1 1/4
Feed Comp. >
DropPos. Correct >
Heater >
key.
Logical Seek HOST
Overprint HOST
<< >>
1/4 Setup 1
> Feed Comp.
> DropPos. Correct
> Heater
Host Host
Logical Seek
Host Host
Overprint
>> << >>
Setup 1
2/4
> Drying Time
0mm Margin/L 0mm
0mm Margin/R 0mm
Host Refresh Host
OFF Refresh Left OFF
>> << >>
3/4 Setup 1
Standard Drying Fan Standard
> Feed Speed
> MAPS4
> Auto Nozzle Maint.
OFF Interval Wiping OFF
>> << >>
1/4
>
>
>
2/4
>
3/4
>
>
>