Chapter 3 Setup; About Setup Menu - MIMAKI TS55-1800 Operation Manual

Chapter 3 Setup

About SETUP MENU

On SETUP MENU, you can set the print conditions to match the media you usually use.
Local <Setup 1>
LOW 1620mm
POST1 POST2
30° /40° 30° /50°
TEST PRINT TEST PRINT
MENU MENU REMOTE REMOTE
CLEANING CLEANING
 SETUP MENUs at-a-glance
Local <Setup 1>
LOW 1620mm
POST1 POST2
30° /40° 30° /50°
TEST PRINT TEST PRINT
MENU MENU REMOTE REMOTE
CLEANING CLEANING
SETUP 1 1/4
FEED COMP. >
DROP.POScorrect >
HEATER >
LOGICAL SEEK HOST
Overprint HOST
<< >>
SETUP 1 2/4
DRYING TIME >
MARGIN/LEFT HOST
MARGIN/RIGHT HOST
VACUUM HOST
FEED SPEED HOST
<< >>
SETUP 1 3/4
AUTO CLEANING >
EXTERNAL HEATER OFF
MAPS4 >
Pass density correct Lv. 3
PRE FEED OFF
<< >>
SETUP 1 4/4
SETUP RESET >
<< >>
3-2
MENU SETUP
SETUP > ● SETUP 1
MAINTENANCE > ○ SETUP 2
MACHINE SETUP > ○ SETUP 3
NOZZLE CHECK > ○ SETUP 4
INFORMATION >
SETUP 1 1/4 SETUP 1
FEED COMP. > FEED COMP.
DROP.POScorrect > DROP.POScorrect
HEATER > HEATER
LOGICAL SEEK HOST LOGICAL SEEK
Overprint HOST Overprint
<< >> <<
SETUP 1 2/4 SETUP 1
DRYING TIME > DRYING TIME
MARGIN/LEFT HOST MARGIN/LEFT
MARGIN/RIGHT HOST MARGIN/RIGHT
VACUUM HOST VACUUM
FEED SPEED HOST FEED SPEED
<< >> <<
SETUP 1 3/4 SETUP 1
AUTO CLEANING > AUTO CLEANING
EXTERNAL HEATER OFF EXTERNAL HEATER
MAPS4 > MAPS4
Pass density correct Lv. 3 Pass density correct
PRE FEED OFF PRE FEED
<< >> <<
: Press this to select SETUP MENU, or to switch to the
previous screen.
: Press this to switch to the next screen.
: Use these to select a setting item.
: Press this to confirm a setting, etc.
>
>
Select "SETUP 1 to 4" and then
>
press the
>
<< Name >>
1/4 SETUP 1
> FEED COMP.
> DROP.POScorrect
> HEATER
HOST LOGICAL SEEK
HOST Overprint
>> <<
2/4 SETUP 1
> DRYING TIME
HOST MARGIN/LEFT
HOST MARGIN/RIGHT
HOST VACUUM
HOST FEED SPEED
>> <<
3/4 SETUP 1
> AUTO CLEANING
OFF EXTERNAL HEATER
> MAPS4
Lv. 3 Pass density correct
OFF PRE FEED
>> <<
SETUP 1
FEED COMP.
DROP.POScorrect
HEATER HOST
key.
LOGICAL SEEK HOST
Overprint HOST
<< >>
1/4 SETUP 1
> FEED COMP.
> DROP.POScorrect
> HEATER
HOST LOGICAL SEEK
HOST Overprint
>> <<
2/4 SETUP 1
> DRYING TIME
HOST MARGIN/LEFT
HOST MARGIN/RIGHT
HOST VACUUM
HOST FEED SPEED
>> <<
3/4 SETUP 1
> AUTO CLEANING
OFF EXTERNAL HEATER
> MAPS4
Lv. 3 Pass density correct
OFF PRE FEED
>> <<
1/4
>
>
1/4
>
>
>
HOST
HOST
>>
2/4
>
HOST
HOST
HOST
HOST
>>
3/4
>
OFF
>
Lv. 3
OFF
>>