Afd Port Diagnos.; Bus Jog; Set-Up Select; Preset Reference Select - Danfoss VLT AutomationDrive Programming Manual

Parameter Descriptions

8-55 Set-up Select

Option:
[1] Bus
3 3
[2] Logic
AND
[3] Logic OR
*

8-56 Preset Reference Select

Option:
[0] Digital
input
[1] Bus
[2] Logic AND Activates Preset Reference selection via the
[3] Logic OR
*
8-57 Profidrive OFF2 Select
Select control of the drive OFF2 selection via the terminals
(digital input) and/or via the serial communication bus. This
parameter is active only when par. 8-01 Control Site is set to [0]
Digital and ctrl. word and par. 8-10 is set to [1] Profidrive profile.
Option:
[0]
[1]
[2]
[3]
*
8-58 Profidrive OFF3 Select
Select control of the drive OFF3 selection via the terminals
(digital input) and/or via the serial communication bus. This
parameter is active only when par. 8-01 Control Site is set to [0]
Digital and control word and par. 8-10 is set to [1] Profidrive
profile.
Option:
[0]
[1]
3-92
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-20872-Danfoss-131H4490-VLT-Automation-VT-Drive-VFD-FC302-460V-25-HP.aspx
FC 300 Programming Guide
Function:
Activates the set-up selection via the serial
communication port or serial communication
option.
Activates the set-up selection via the serial
communication bus/serial communication port,
AND additionally via one of the digital inputs.
Activate the set-up selection via the serial
communication bus/serial communication port
OR via one of the digital inputs.
Function:
Select control of the Adjustable frequency drive
Preset Reference selection via the terminals
(digital input) and/or via the serial communi-
cation bus.
Activates Preset Reference selection via a digital
input.
Activates Preset Reference selection via the
serial communication port or serial communi-
cation option.
serial communication bus/serial communication
port, AND additionally via one of the digital
inputs.
Activates the Preset Reference selection via the
serial communication bus/serial communication
port OR via one of the digital inputs.
Function:
Digital input
Bus
Logic AND
Logic OR
Function:
Digital input
Bus
MG33MD22 - VLT
8-58 Profidrive OFF3 Select
Select control of the drive OFF3 selection via the terminals
(digital input) and/or via the serial communication bus. This
parameter is active only when par. 8-01 Control Site is set to [0]
Digital and control word and par. 8-10 is set to [1] Profidrive
profile.
Option:
[2] Logic AND
[3] Logic OR
*

3.10.6 8-8* AFD Port Diagnos.

These parameters are used for monitoring the bus
communication via the Adjustable Frequency Drive Port.
8-80 Bus Message Count
Range: Function:
0 [0 - 0 ] This parameter shows the number of valid
*
messages detected on the bus.
8-81 Bus Error Count
Range: Function:
0 [0 - 0 ] This parameter shows the number of messages
*
with faults (e.g., CRC fault), detected on the bus.
8-82 Slave Messages Rcvd
Range: Function:
0 [0 - 0 ] This parameter shows the number of valid
*
messages addressed to the slave, sent by the
Adjustable frequency drive.
8-83 Slave Error Count
Range: Function:
0 [0 - 0 ] This parameter shows the number of error
*
messages, which could not be executed by the
Adjustable frequency drive.

3.10.7 8-9* Bus Jog

8-90 Bus Jog 1 Speed
Range:
100 RPM [ 0 - par. 4-13
*
RPM]
®
is a registered Danfoss trademark
Function:
Function:
Enter the jog speed. This is a fixed
jog speed activated via the serial
port or serial communication bus
option.