Danfoss VLT AutomationDrive Programming Manual page 82

Parameter Descriptions
[121] Remote Output is high when 3-13 Reference Site =
reference Remote [1] or Linked to hand/auto [0]
active while the LCP is in [Auto on] mode. See
above.
[122] No alarm Output is high when no alarm is present.
[123] Start command Output is high when there is an active
active Start command (i.e., via digital input bus
connection or [Hand on] or [Auto on]),
and no Stop or Start command is active.
[124] Running Output is high when the Adjustable
reverse frequency drive is running counter
clockwise (the logical product of the
status bits 'running' AND 'reverse').
[125] Drive in hand Output is high when the Adjustable
mode frequency drive is in [Hand on] mode (as
indicated by the LED light above [Hand
on]).
[126] Drive in auto Output is high when the Adjustable
mode frequency drive is in [Hand on] mode (as
indicated by the LED above [Auto on]).
[151] ATEX ETR cur. Selectable if 1-90 Motor Thermal Protection
alarm is set to [20] or [21]. If the alarm 164
ATEX ETR cur.lim.alarm is active, the
output will be 1.
[152] ATEX ETR freq. Selectable if 1-90 Motor Thermal Protection
alarm is set to [20] or [21]. If the alarm 166
ATEX ETR freq.lim.alarm is active, the
output will be 1.
[153] ATEX ETR cur. Selectable if1-90 Motor Thermal Protection
warning is set to [20] or [21]. If the alarm 163
ATEX ETR cur.lim.warning is active, the
output will be 1.
[154] ATEX ETR freq. Selectable if 1-90 Motor Thermal Protection
warning is set to [20] or [21]. If the warning 165
ATEX ETR freq.lim.warning is active, the
output will be 1.
[188] AHF Capacitor The capacitors will be turned on at 20%
Connect (hysteresis of 50% gives an interval of
10%–30%). The capacitors will be discon-
nected below 10%. The off delay is 10 s
and will restart if the nominal power goes
above 10% during the delay. 5-80 AHF
Cap Reconnect Delay is used to guarantee
a minimum off-time for the capacitors.
[189] External fan The internal logics for the internal fan
control control is transferred to this output to
make it possible to control an external
fan (relevant for HP duct cooling).
5-30 Terminal 27 Digital Output
Option: Function:
[0] No operation Functions are described under 5-3* Digital
*
Outputs
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-20872-Danfoss-131H4490-VLT-Automation-VT-Drive-VFD-FC302-460V-25-HP.aspx
FC 300 Programming Guide
5-31 Terminal 29 Digital Output
Option:
[0]
5-32 Term X30/6 Digi Out (MCB 101)
Option:
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]
[14]
[15]
[16]
[17]
[18]
[19]
[20]
[21]
[22]
[23]
[24]
[25]
[26]
[27]
[28]
[29]
[30]
[31]
[32]
[33]
[38]
[39]
[40]
[41]
[42]
®
MG33MD22 - VLT is a registered Danfoss trademark
Function:
No operation Functions are described under 5-3* Digital
*
Outputs
This parameter only applies to FC 302
Function:
No operation This parameter is active when
*
option module MCB 101 is
mounted in the Adjustable
frequency drive. Functions are
described under 5-3* Digital
Outputs
Control ready
Drive ready
Drive rdy/rem ctrl
Enable / no warning
Running
Running / no warning
Run in range/no warn
Run on ref/no warn
Alarm
Alarm or warning
At torque limit
Out of current range
Below current, low
Above current, high
Out of speed range
Below speed, low
Above speed, high
Out of feedb. range
Below feedback, low
Above feedback, high
Thermal warning
Ready,no thermal W
Remote,ready,no TW
Ready, Voltage OK
Reverse
Bus OK
Torque limit & stop
Brake, no brake war
Brake ready, no fault
Brake fault (IGBT)
Relay 123
Mech brake ctrl
Safe stop active
Motor feedback error
Tracking error
Out of ref range
Below reference, low
Above ref, high
3 3
3-57