Chrysler 1997 Stratus Convertible RHD Service Manual page 826

9 - 90 2.5L ENGINE
SPECIFICATIONS (Continued)
ENGINE SPECIFICATIONS (CONT.)
Piston
O.D.
Piston to Cylinder Clearance
Ring End Gap
No. 1
No. 2
Oil
Ring Side Clearance No. 1
No. 2
Connecting Rod
Length — Center to Center
Parallelism — Twist
Torsion
Big End Thrust Clearance
Crankshaft
End Play
Main Journal Diameter
Pin Diameter
Bearing Surface Out-of-Round
Bearing Surface Taper
Bearing Oil Clearance
Undersize Service Bearing
Cylinder Block
I.D. (Bore)
Flatness of Top Surface
Grinding Limit of Top Surface
* Includes/Combined With Cylinder Head Grinding
Oil Pump
Relief Valve Opening Pressure
Outer Rotor to Case Clearance
Rotor End Clearance
Inner Rotor Pilot to Case Clearance
Minimum Pressure, Engine Fully Warmed Up at Idle 3000 RPM
Description Standard Dimension
83.5 mm
(3.29 inches)
0.02 to 0.04 mm
(0.0008 to 0.0016 inch)
0.25 to 0.40 mm
(.010 to .016 inch)
0.40 to 0.55 mm
(.016 to .022 inch)
0.15 to 0.50 mm
(.006 to .019 inch)
0.030 to 0.07 mm
(.0012 to .0028 inch)
(0.002 to 0.06 mm
(.0007 to .0024 inch)
140.9 to 141.0 mm
(5.547 to 5.551 inches)
0.05 mm
(0.0019 inch)
0.1 mm
(0.0039 inch)
0.10 to 0.25 mm
(0.004 to 0.010 inch)
0.05 to 0.25 mm
(0.002 to 0.010 inch)
60.000 mm
(2.362 inches)
50.000 mm
(1.969 inches)
0.03 mm Max.
(0.001 inch) Max.
0.005 mm Max.
(0.0002 inch) Max.
0.02 to 0.04 mm
(0.0008 to 0.0016 inch)
0.25 to 0.50 - 0.75 mm
(0.010 to 0.020 - 0.030 inch)
83.50 to 83.53 mm
(3.29 inches)
0.05 mm
(0.002 inch)
0.2 mm*
(0.008 inch)
2
5.0 to 6.0 kg/cm
(71.45 to 85.76 psi)
0.10 to 0.18 mm
(0.004 to 0.007 inch)
0.06 to 0.18 mm
(0.0024 to 0.0071 inch)
0.03 to 0.07 mm
(0.001 to 0.0028 inch)
41 kPa (6 psi)
241-517 kPa (35-75 psi)
JX
Service Limit
—
—
0.8 mm
(.031 inch)
0.8 mm
(.031 inch)
1.0 mm
(.039 inch)
0.1 mm
(.004 inch)
0.1 mm
(.004 inch)
—
—
—
0.4 mm
(0.016 inch)
0.4 mm
(0.016 inch)
—
—
—
—
—
—
—
0.1 mm
(0.004 inch)
0.2 mm*
(0.008 inch)
—
0.35 mm
(0.0138 inch)
0.09 mm
(0.0035 inch)
0.15 mm
(0.006 inch)