Page 1 2 0 1 1 CONVERTIBLE O W N E R ’ S M A N U A L...
Page 2 With respect to any Vehicles Sold in Canada, the name This manual illustrates and describes the operation of Chrysler Group LLC shall be deemed to be deleted and features and equipment that are either standard or op- the name Chrysler Canada Inc. used in substitution tional on this vehicle.
Page 3: Introduction
TABLE OF CONTENTS SECTION PAGE ............3 INTRODUCTION .
Page 5: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Vehicle Identification Number ....6 How To Use This Manual .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech- LLC vehicle. Be assured that it represents precision nicians and genuine MOPAR parts, and cares about workmanship, distinctive styling, and high quality - all your satisfaction.
Page 7 INTRODUCTION 5...
Page 8: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 9: Vehicle Modifications/Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a accident resulting in serious injury or death. Stamped VIN Location NOTE: It is illegal to remove or alter the VIN.
Page 11: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 To Arm The System ....18 Ignition Key Removal .
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Open Window Feature — Wind Buffeting ..... . . 36 If Equipped ......25 Trunk Lock And Release .
Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Enhanced Seat Belt Use Reminder System Child Restraints ..... . 67 (BeltAlert ) ......54 Engine Break-In Recommendations .
Page 14: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer.
Page 15 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition switch lock cylinder to warn you that this safety feature is inop- erable.
Page 16: Key-In-Ignition Reminder
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The time for this feature is programmable. Refer to CAUTION! “Electronic Vehicle Information Center (EVIC)/ Personal Settings (Customer-Programmable Fea- An unlocked car is an invitation to thieves. Always tures)” in “Understanding Your Instrument Panel” for remove key from the ignition and lock all doors further information.
Page 17 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 The system uses ignition keys, which have an embedded an invalid key to start the engine. Either of these condi- electronic chip (transponder), to prevent unauthorized tions will result in the engine being shut off after two vehicle operation.
Page 18: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE authorized dealer or by using the Customer Key Pro- CAUTION! gramming procedure. This procedure consists of pro- gramming a blank key to the vehicle electronics. A blank The Sentry Key Immobilizer system is not compat- key is one which has never been programmed.
Page 19: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 3. Insert the second valid key into the ignition switch. Repeat this procedure to program up to eight keys. If you Turn the ignition switch to the ON/RUN position within do not have a programmed Sentry Key contact your 15 seconds.
Page 20: Vehicle Security Alarm - If Equipped
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE VEHICLE SECURITY ALARM — IF EQUIPPED To Arm The System The Vehicle Security Alarm monitors the doors and trunk 1. Remove the keys from the ignition switch and get out for unauthorized entry and ignition switch for unauthor- of the vehicle.
Page 21: To Disarm The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 • The Vehicle Security Alarm remains armed during NOTE: • During the 16-second arming period, if a door is trunk entry. Pressing the trunk button will not disarm opened or the ignition switch is turned to ON/RUN, the Vehicle Security Alarm.
Page 22: Illuminated Entry - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tamper Alert NOTE: • The front courtesy overhead console and door cour- If the alarm was triggered, but the warning signals have timed out, the park and taillights flash three times, and tesy lights do not turn on if the dimmer control is in the horn will chirp three times, when unlocking the the Dome ON position (extreme top position).
Page 23: To Unlock The Doors
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 • Inserting the key into the ignition switch disables all To Unlock The Doors buttons on the RKE transmitter. Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door or twice to unlock both doors.
Page 24 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the inside the vehicle will activate the Vehicle Security Alarm following procedure: System. Opening a door with the Vehicle Security Alarm activated will cause the alarm to sound. Press the UN- 1.
Page 25: To Lock The Doors
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • For vehicles not equipped with the EVIC, perform the Opening a door with the Vehicle Security Alarm acti- following procedure: vated will cause the alarm to sound. Press the UNLOCK button to deactivate the Vehicle Security Alarm System. 1.
Page 26: Convertible Top Operation Button - If Equipped
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sound Horn With Lock 3. Test the feature while outside of the vehicle by press- This feature will cause the horn to chirp when the doors ing the LOCK button on the RKE transmitter with the are locked with the RKE transmitter.
Page 27: To Unlatch The Trunk
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 To Unlatch The Trunk The Panic Alarm will stay on for three minutes unless Press the TRUNK button on the RKE transmitter two you turn it off by pressing the PANIC button a second times to unlatch the trunk.
Page 28: General Information
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not touch the battery terminals that are on the back 2. Remove and replace the battery. Avoid touching the housing or the printed circuit board. new battery with your fingers. Skin oils may cause battery deterioration.
Page 29: Remote Starting System - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • Obstructions between the vehicle and the Key Fob If your RKE transmitter fails to operate from a normal distance, check for these two conditions: may reduce this range. 1. Weak battery in the RKE transmitter. The expected life How To Use Remote Start of a battery is five years.
Page 30 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • System not disabled from previous remote start event Remote Start Abort Message On Electronic Vehicle Information Center (EVIC) — If Equipped • Vehicle theft alarm not active The following messages will display in the EVIC if the vehicle fails to remote start or exits remote start prema- WARNING! turely:...
Page 31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 To Enter Remote Start Mode Remote start will also cancel if any of the following occur: Press and release the REMOTE START button • The engine stalls or RPM exceeds 2500 on the RKE transmitter twice within five sec- •...
Page 32: Door Locks
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To avoid unintentional shut downs, the system will disable the one-time press of the remote start button for two seconds after receiving a valid remote start request. To Exit Remote Start Mode And Drive The Vehicle Before the end of the 15 minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm (if...
Page 33: Power Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Power Door Locks WARNING! A door lock switch is located on the driver and passenger • For personal security and safety in the event of an door trim panel. Press this switch to lock or unlock the doors.
Page 34 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Door Locks — If Equipped 6. The vehicle speed is 0 mph (0 km/h). When enabled, the door locks will lock automatically Auto Unlock Door On Exit Programming when the vehicle’s speed exceeds 15 mph (24 km/h). The The Automatic Unlock Doors On Exit feature can be Automatic Door Locks feature can be enabled or disabled enabled or disabled as follows:...
Page 35: Windows
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 3. Press the power door UNLOCK switch to unlock the doors. 4. A single chime will indicate the completion of the programming. NOTE: This feature will not be functional until the vehicle has been driven and the shift lever returned to the PARK position.
Page 36 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: to its full up position after closing the door. This action • If a fluttering noise is heard from the rear seat belts allows the door to open without resistance and prevents while driving with the windows down, safely bring window and top seal damage.
Page 37 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 will remain active for 45 seconds after the ignition switch 1. Lowering all four windows to the full open position. is turned to the LOCK position. Opening either door will 2. Press and hold the Power Top Switch in the Close cancel this feature.
Page 38: Wind Buffeting
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE window control, press and release the window LOCK Wind Buffeting button again (setting it in the up position). Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.
Page 39 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 The trunk release button on the dash To unlatch the trunk lid from outside the vehicle, press will be disabled if the vehicle is locked and release the TRUNK RELEASE button on the RKE by pressing the power door lock transmitter two times.
Page 40: Trunk Safety Warning
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK SAFETY WARNING WARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended.
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 • Advanced Front Air Bags for driver and front passen- all the way out and then adjusting the belt to the desired length to restrain a child seat or secure a large item in a seat •...
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can take to minimize the ride properly buckled up in the rear seat. Never allow risk of harm from a deploying air bag: children to slide the shoulder belt behind them or under their arm.
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 4. Do not lean against the door or window. If your WARNING! (Continued) vehicle has side air bags, and deployment occurs, the • Being too close to the steering wheel or instrument side air bags will inflate forcefully into the space panel during Advanced Front Air Bag deployment between you and the door.
Page 44: Lap/Shoulder Belts
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even normal conditions. However, in an accident, the belt will on short trips. Someone on the road may be a poor driver lock and reduce the risk of you striking the inside of the and cause an accident that includes you.
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 2. The seat belt latch plate is on the outboard side of the WARNING! (Continued) front seat, next to your arm. Grasp the latch plate and • Wearing your belt in the wrong place could make pull out the belt.
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click.” • A belt that is buckled into the wrong buckle will not protect you properly.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 4. Position the lap belt across your thighs, below your WARNING! (Continued) abdomen. To remove slack in the lap belt portion, pull up • A belt that is worn under your arm is dangerous. on the shoulder belt.
Page 48: Lap/Shoulder Belt Untwisting Procedure
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. WARNING! The belt will automatically retract to its stowed position. • A lap belt worn too high can increase the risk of If necessary, slide the latch plate down the webbing to allow the belt to retract fully.
Page 49: Seat Belts In Passenger Seating Positions
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 1. Position the latch plate as close as possible to the Driver Center Passenger anchor point. First Row 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, Second Row grasp and twist the belt webbing 180°...
Page 50: Automatic Locking Retractor Mode (Alr) - If Equipped
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Locking Retractor Mode (ALR) — If 3. Allow the belt to retract. As the belt retracts, you will Equipped hear a clicking sound. This indicates the safety belt is In this mode, the shoulder belt is automatically pre- now in the Automatic Locking Mode.
Page 51: Energy Management Feature
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Energy Management Feature Seat Belt Pretensioners This vehicle has a safety belt system with an Energy The seat belts for both front seating positions are Management feature in the front seating positions to help equipped with pretensioning devices that are designed to further reduce the risk of injury in the event of a head-on remove slack from the seat belt in the event of an...
Page 52: Supplemental Active Head Restraints (Ahr) - If Equipped
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Active Head Restraints (AHR) — If When AHRs deploy during a rear impact, the front half Equipped of the head restraint extends forward to minimize the gap These head restraints are passive, deployable compo- between the back of the occupant’s head and the AHR.
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 CAUTION! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of an accident.
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Grasp the deployed AHR from the rear seat. 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. Hand Positioning Points On AHR 2.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 AHR In Reset Position 3 — Final Downward Movement To Engage Locking Mechanism NOTE: 4. The AHR front soft foam and trim half should lock • If you have difficulties or problems resetting the into the back decorative plastic half.
Page 56: Enhanced Seat Belt Use Reminder System (Beltalert )
BeltAlert Programming ignition is on. If the driver is unbelted, the Seat Belt Reminder Light will turn on and remain on until the NOTE: Chrysler Group LLC does not recommend de- driver seatbelt is fastened. activating BeltAlert . The BeltAlert warning sequence begins within 60 sec-...
Page 57: Seat Belts And Pregnant Women
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 2. Turn the ignition switch to the ON/RUN position (do Seat Belts And Pregnant Women not start the engine), and wait for the Seat Belt Reminder We recommend that pregnant women use the seat belts Light to turn off.
Page 58: Supplemental Restraint System (Srs) - Air Bags
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Using a seat belt extender when not needed can increase the risk of injury in an accident. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 The Advanced Front Air Bags have a multistage inflator NOTE: • Air Bag covers may not be obvious in the interior trim, design. This allows the air bag to have different rates of inflation that are based on the severity and type of but they will open during air bag deployment.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Supplemental Seat-Mounted Side Air Bags (SAB) WARNING! • Front and Side Impact Sensors • No objects should be placed over or near the air bag on the instrument panel, because any such •...
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Supplemental Seat-Mounted Side Air Bags (SAB) When the air bag deploys, it opens the seam between the Supplemental Seat-Mounted Side Air Bags may provide front and side of the seat’s trim cover. Each air bag enhanced protection to help protect an occupant during a deploys independently;...
Page 62: Air Bag Deployment Sensors And Controls
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Along with seat belts and pretensioners, Advanced Front Advanced Front Air Bags are designed to provide addi- Air Bags work with the knee bolsters to provide im- tional protection by supplementing the seat belts in proved protection for the driver and front passenger.
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Because air bag sensors measure vehicle deceleration Also, the ORC turns on the Air Bag Warning over time, vehicle speed and damage by themselves are Light in the instrument panel for approxi- not good indicators of whether or not an air bag should mately four to eight seconds for a self-check have deployed.
Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE are possible, based on the collision type and severity. The WARNING! steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as Ignoring the Air Bag Warning Light in your instru- the air bags inflate to their full size.
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Based on the severity and type of collision, the side air event the ORC will determine whether to have the bag inflator on the crash side of the vehicle may be Enhanced Accident Response System perform the follow- triggered, releasing a quantity of non-toxic gas.
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision, which deploys the air bags, any throat irritation, move to fresh air. If the irritation or all of the following may occur: continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s in- •...
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Maintaining Your Air Bag System WARNING! (Continued) • Do not attempt to modify any part of your air bag WARNING! system. The air bag may inflate accidentally or • Modifications to any part of the air bag system may not function properly if modifications are could cause it to fail when you need it.
Page 68: Event Data Recorder (Edr)
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag Warning Light NOTE: If the speedometer, tachometer, or any engine You will want to have the air bags ready to related gauges are not working, the Occupant Restraint inflate for your protection in a collision. The Controller (ORC) may also be disabled.
Page 69: Child Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 • Whether or not the driver and passenger safety belts To read data recorded by an EDR, special equipment is were buckled/fastened; required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, •...
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Child Restraints WARNING! • Safety experts recommend that children ride In a collision, an unrestrained child, even a tiny baby, rearward-facing in the vehicle until they are at least can become a projectile inside the vehicle. The force one year old and weigh at least 20 lbs (9 kg).
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 The belt-positioning booster seat is for children weighing WARNING! more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit Rearward-facing child seats must never be used in with knees bent over the vehicle’s cushion while the the front seat of a vehicle with a front passenger air...
Page 72 Follow the manufacturer’s directions ex- • Before buying any restraint system, make sure that it actly when installing an infant or child restraint. has a label certifying that it meets all applicable Safety (Continued) Standards. Chrysler Group LLC also recommends that...
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 you make sure that you can install the child restraint in WARNING! the vehicle where you will use it, before you buy it. When your child restraint is not in use, secure it in •...
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH-compatible child restraints in adjacent rear seat- ing positions, you can use the LATCH anchors or the vehicle’s seat belts. If your child restraints are not LATCH-compatible, you can only install the child re- straints using the vehicle’s seat belts.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 have tether straps, and you are urged to take advantage Installing The LATCH-Compatible Child Restraint of all of the available attachments provided with your System child restraint in any vehicle. We urge you to carefully follow the directions of the manufacturer when installing your child restraint.
Page 76 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE tether anchors are underneath access covers in the carpet the access cover on the carpet covering the back of the covering the back of the seat where you see this symbol. seat and attach the tether strap hook to the anchor. Be careful to route the tether strap to provide the most direct Many, but not all, restraint systems will be equipped with path between the anchor and the child restraint.
Page 77 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Remind all children in the vehicle that the seat belts are seat belts are designed to keep the lap portion of the seat not toys and should not be played with, and never leave belt tight around the child restraint so that it is not your child unattended in the vehicle.
Page 78 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing a Child Restraint with an ALR: several times to shorten it. Insert the latch plate into the buckle with the release button facing out. 1. To install a child restraint with ALR, first, pull enough •...
Page 79 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 4. Open the access cover (C) on the carpet covering the back of the seat and attach the tether strap hook (D) to the anchor. Child Tether Access Port Cover 3. Push the tether strap and hook (B) through the access port and down into the trunk.
Page 80: Engine Break-In Recommendations
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS WARNING! A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. An incorrectly anchored tether strap could lead to increased head motion and possible injury to the Drive moderately during the first 300 miles (500 km).
Page 81: Safety Tips
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 A new engine may consume some oil during its first few WARNING! (Continued) thousand miles (kilometers) of operation. This should be • It is extremely dangerous to ride in a cargo area, considered a normal part of the break-in and not inter- inside or outside of a vehicle.
Page 82: Exhaust Gas
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the WARNING! vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- Exhaust gases can injure or kill.
Page 83 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 a collision if they have been damaged (i.e., bent retractor, Floor Mat Safety Information torn webbing, etc.). If there is any question regarding belt Always use floor mats designed to fit the footwell of your or retractor condition, replace the belt.
Page 84 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Never place or install floor mats or other floor • Always make sure that objects cannot fall into the coverings in the vehicle that cannot be properly driver footwell while the vehicle is moving.
Page 85: Periodic Safety Checks You Should Make Outside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Periodic Safety Checks You Should Make Outside Door Latches The Vehicle Check for positive closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
Page 87: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Convertible Top Operation ....89 Emergency Bypass Mode (To Raise The Top Only) ....107 Power Convertible Top Usage Precautions .
Page 88 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect™ Phone — If Equipped ... 111 Seats ......146 Operation .
Page 89 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Headlights With Wipers (Available With Windshield Wipers And Washers ..164 Automatic Headlights Only) ... . 159 Intermittent Wiper System .
Page 90 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing ....171 Cupholders ......182 Garage Door Opener —...
Page 91: Convertible Top Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 CONVERTIBLE TOP OPERATION WARNING! CAUTION! The convertible top does not provide the structural protection that a reinforced metal roof does and the Failure to follow these cautions may cause interior fabric top cannot be expected to prevent the ejection water damage, stains or mildew on the top material: of the occupants in a collision.
Page 92: Power Convertible Top Usage Precautions
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When operating the power convertible top, the trunk lid Power Convertible Top Usage Precautions will pivot at the rear of the vehicle, swing open by the NOTE: rear window, and then pivot backward. This allows room •...
Page 93 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 • Opening and closing the top consecutively without the CAUTION! (Continued) engine running may run the battery down. • Do not push items too far into the trunk, particu- • If a fluttering noise is heard from the rear seat belts larly when the top is retracted into its stowage area while driving with the top down, safely bring the in the trunk.
Page 94 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) CAUTION! • Never attempt to lower a frozen convertible top. • Do not operate the power top with the hydraulic Wait until the top is thawed before lowering it into pump valve open. the stowage compartment.
Page 95 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 CAUTION! (Continued) WARNING! • Always close the top when leaving your vehicle so Failure to follow these warnings can result in injuries as not to leave the interior exposed to potentially that are serious or fatal to you, your passengers, and damaging outdoor conditions.
Page 96: Cargo Shield
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE seat the tabs at each end of the cargo shield in the V slots WARNING! (Continued) in the trunk liner. Doing so closes a switch that allows top • When using the power top switch on the instru- operation.
Page 97 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 forward onto the horizontal panel, then grasp both panels and lift them to the forward, upright position in the trunk. Cargo Shield Positioning The Cargo Shield For Cargo Storage To maximize the storage space in the trunk, the cargo shield can be stowed in the forward portion of the trunk.
Page 98: Power Convertible Top Controls
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Convertible Top Controls Lowering the Power Convertible Top The power top switch is located on the front of the center Using The Power Top Switch console. NOTE: The power top switch will operate when the There is also a power top button on the Remote Keyless ignition switch is turned to the ON or ACC position and Entry (RKE) transmitter for remotely lowering the power...
Page 99: Raising The Power Convertible Top
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Using The Remote Keyless Entry Transmitter Raising The Power Convertible Top NOTE: Steps 1 – 3 must be performed within five Using The Power Top Switch seconds. NOTE: The power top switch will operate when the 1.
Page 100: Wind Stop - If Equipped
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manually Wind Stop — If Equipped Closing the power convertible top manually is a compli- The Wind Stop installs in the backseat area of the vehicle. cated and physically demanding procedure, and it re- The Wind Stop will not interfere with power top opera- quires a special tool to do so.
Page 101 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 NOTE: The frames must lie flat on each other in order to 4. Pivot the small frame (1) away from the large frame (2) snap them together. until the pivot lock (3) engages to lock the two frames in an L shape.
Page 102 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Unfold both stems at the rear of the large frame. 6. Align and insert the stems into the slot in each trim panel.
Page 103 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 7. Align the pins at the front of the large frame with the Removing And Storing The Wind Stop hole in each trim panel. Slide the pins outward until fully Reverse the installation procedure to remove, fold, and extended into each hole.
Page 104: Power Convertible Top Operation And Warning Messages
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Convertible Top Operation And Warning Messages When the appropriate conditions exist, the PTCM displays various power convertible top operation and warning messages in the Electronic Vehicle Information Center (EVIC) – if equipped, or in the Odometer for vehicles not equipped with the EVIC.
Page 105 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 EVIC EVIC Odometer Odometer Odometer Odometer Chime Condition Operator Message Message Message Message Message Message Action Display (< 5 mph Display (> 5 mph Display Required Time [8 km/h]) Time [8 km/h]) Time SECURE 9 sec.
Page 106 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE EVIC EVIC Odometer Odometer Odometer Odometer Chime Condition Operator Message Message Message Message Message Message Action Display (< 5 mph Display (> 5 mph Display Required Time [8 km/h]) Time [8 km/h]) Time SPEED 9 sec.
Page 107 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 EVIC EVIC Odometer Odometer Odometer Odometer Chime Condition Operator Message Message Message Message Message Message Action Display (< 5 mph Display (> 5 mph Display Required Time [8 km/h]) Time [8 km/h]) Time CONVERT- 6 sec.
Page 108 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The PTCM will lockout the power convertible top system if the vehicle charging system is malfunction- ing, or the battery is run down, or the hydraulic pump is overheating. In addition, the system prohibits lower- ing the top when ambient temperature is at 0°F (-18°C) or lower and raising the top when ambient temperature is below -40°F (-40°C).
Page 109: Emergency Bypass Mode (To Raise The Top Only)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Emergency Bypass Mode CAUTION! (Continued) (To Raise The Top Only) • Using the Emergency Bypass Mode could poten- This procedure is only to be used to raise the top when tially damage the convertible top and should only the top cannot be returned to the UP (raised) position by be used to raise the power top to the UP (raised) pressing the POWER TOP switch or is in a position in...
Page 110: Mirrors
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
Page 111: Outside Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Outside Mirrors Power Mirrors To receive maximum benefit, adjust the outside mirrors The power mirror switch is located on the driver’s door to center on the adjacent lane of traffic and a slight trim.
Page 112: Heated Mirrors - If Equipped
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After selecting a mirror, move the knob in the same Heated Mirrors — If Equipped direction you want the mirror to move. When finished, These mirrors are heated to melt frost or ice. This return the knob to the center “O”...
Page 113: Uconnect™ Phone - If Equipped
Bluetooth “Hands-Free Profile”, Ver- sion 0.96 or higher. See the Uconnect™ website for supported phones. For Uconnect™ customer support, visit the following websites: • www.chrysler.com/uconnect • www.dodge.com/uconnect Vanity Mirror Uconnect™ Phone — IF EQUIPPED • www.jeep.com/uconnect Uconnect™ Phone is a voice-activated, hands-free, in- •...
Page 114 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect™ Phone allows you to transfer calls between WARNING! the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system’s Any voice commanded system should be used only microphone for private conversation.
Page 115: Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Voice Command Button Operation Actual button location may vary with the ra- Voice commands can be used to operate the Uconnect™ dio. The individual buttons are described in the Phone and to navigate through the Uconnect™ Phone “Operation”...
Page 116 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE example, you can use the compound form voice Cancel Command command “Phonebook New Entry”, or you can break At any prompt, after the beep, you can say “Cancel” and the compound form command into two voice com- you will be returned to the main menu.
Page 117 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 • When prompted, after the beep, say “Pair a Device” phone to use if multiple mobile phones are in the and follow the audible prompts. vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the •...
Page 118 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Uconnect™ Phone will confirm the phone number • The Uconnect™ system will confirm the name and and then dial. The number will appear in the display then dial the corresponding phone number, which of certain radios.
Page 119 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 • When prompted, enter the number designation (e.g., Phonebook Download – Automatic Phonebook “Home”, “Work”, “Mobile”, or “Other”). This will Transfer From Mobile Phone allow you to store multiple numbers for each phone- If equipped and specifically supported by your phone, book entry, if desired.
Page 120 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Depending on the maximum number of entries down- Edit Uconnect™ Phonebook Entries loaded, there may be a short delay before the latest NOTE: downloaded names can be used. Until then, if avail- •...
Page 121 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 • After you enter the Phonebook Delete menu, you will After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in then be asked for the name of the entry that you wish the phonebook, call the number you just edited, or return to delete.
Page 122: Phone Call Features
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the “Ready” prompt and the following beep, say Delete/Erase “All” Uconnect™ Phonebook Entries “Phonebook List Names”. • Press the button to begin. • The Uconnect™ Phone will play the names of all the •...
Page 123 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 mobile service plan. For example, if your mobile service call waiting that you normally hear when using your plan provides three-way calling, this feature can be mobile phone. Press the button to place the current accessed through the Uconnect™...
Page 124 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Place/Retrieve A Call From Hold Three-Way Calling To put a call on hold, press the button until you hear To initiate three-way calling, press the button a single beep. This indicates that the call is on hold. To while a call is in progress, and make a second phone call, bring the call back from hold, press and hold the as described under “Making a Second Call While Current...
Page 125: Uconnect™ Phone Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 • After the “Ready” prompt and the following beep, say • After the ignition key is switched to OFF, a call can “Redial”. continue on the Uconnect™ Phone for a certain dura- tion, after which the call is automatically transferred •...
Page 126 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the “Ready” prompt and the following beep, say After selecting one of the languages, all prompts and voice commands will be in that language. “Emergency” and the Uconnect™ Phone will instruct the paired mobile phone to call the emergency num- NOTE: After every Uconnect™...
Page 127 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Mexico City in Mexico). Please refer to the 24-Hour WARNING! “Towing Assistance” coverage details on the DVD in the Warranty Information Booklet and the 24-Hour To use your Uconnect™ Phone System in an emer- Towing Assistance references.
Page 128 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Working With Automated Systems is also to be used for navigating through an automated This method is used in instances where one generally has customer service center menu structure, and to leave a to press numbers on the mobile phone keypad while number on a pager.
Page 129 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Barge In — Overriding Prompts Phone And Network Status Indicators The “Voice Command” button can be used when you If available on the radio and/or on a premium display wish to skip part of a prompt and issue your voice such as the instrument panel cluster, and supported by command immediately.
Page 130: Advanced Phone Connectivity
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Following the beep, say “Mute off”. NOTE: Certain brands of mobile phones do not send the dial ring to the Uconnect™ Phone to play it on the vehicle Advanced Phone Connectivity audio system, so you will not hear it. Under this situa- tion, after successfully dialing a number the user may feel Transfer Call To And From Mobile Phone that the call did not go through even though the call is in...
Page 131 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Uconnect™ Phone System, follow the instructions de- Select Another Mobile Phone scribed in your mobile phone User’s Manual. This feature allows you to select and start using another phone paired with the Uconnect™ Phone. List Paired Mobile Phone Names •...
Page 132: Things You Should Know About Your Uconnect™ Phone
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the “Ready” prompt and the following beep, say Phone Voice Training feature may be used. To enter this “Setup Phone Pairing”. training mode, follow one of the two following proce- dures: •...
Page 133 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 • Speak normally, without pausing, just as you would This procedure may be repeated with a new user. The system will adapt to the last trained voice only. speak to a person sitting a few feet/meters away from you.
Page 134 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When navigating through an automated system such • In a convertible vehicle, system performance may be as voice mail, or when sending a page, at the end of compromised with the convertible top down. speaking the digit string, make sure to say “Send”.
Page 135 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 • Performance, such as audio clarity, echo, and loudness Read Messages: to a large degree rely on the phone and network, and If you receive a new text message while your phone is not the Uconnect™...
Page 136 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Send Messages: List of Preset Messages: You can send messages using Uconnect™ Phone. To send 1. Yes a new message: 2. No • Press the button. 3. Where are you? • After the “Ready” prompt and the following beep, say 4.
Page 137 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 • After the “Ready” prompt and the following beep, say 13. I’ll be late “Setup, SMS Incoming Message Announcement,” you 14. Are you there yet? will then be given a choice to change it. 15.
Page 138 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137...
Page 140 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 141 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 142 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
Page 143: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 General Information NOTE: Take care to speak into the Voice Interface This device complies with Part 15 of the FCC rules and System as calmly and normally as possible. The ability of RSS 210 of Industry Canada. Operation is subject to the the Voice Interface System to recognize user voice com- following conditions: mands may be negatively affected by rapid speaking or a...
Page 144: Commands
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you ever wish to interrupt the system while it lists The system will best recognize your speech if the win- options, press the Voice Command button, listen dows are closed, and the heater/air conditioning fan is set to low.
Page 145 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 2. Say a command (e.g., “Help”). Radio AM To switch to the AM band, say “AM” or “Radio AM”. In 3. Use the ON/OFF VOLUME rotary knob to adjust the this mode, you may say the following commands: volume to a comfortable level while the Voice Command •...
Page 146 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Menu Radio” (to switch to the radio menu) Disc To switch to the disc mode, say “Disc”. In this mode, you • “Main Menu” (to switch to the main menu) may say the following commands: Satellite Radio •...
Page 147 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 • “Switch to system setup” − “Continue” (to continue recording) • “Change to setup” − “Delete” (to delete the recording) • “Play Memos” (to play previously recorded memos) • “Main menu setup” or —...
Page 148: Voice Training
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Training SEATS For users experiencing difficulty with the system recog- Seats are a part of the Occupant Restraint System of the nizing their voice commands or numbers the Uconnect™ vehicle. Voice “Voice Training” feature may be used. WARNING! 1.
Page 149: Power Seats
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Power Seats Adjusting The Seat Forward Or Rearward The power seat switch is on the outboard side of the seat The seat can be adjusted both forward and rearward. near the floor. Use the switch to move the seat up, down, Push the seat switch forward or rearward, the seat will forward, rearward, or to tilt the seat.
Page 150: Heated Seats - If Equipped
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Adjusting a seat while driving may be dangerous. Do not place any article under any seat as it may Moving a seat while driving could result in loss of cause damage to the seat controls. control which could cause a collision and serious Heated Seats —...
Page 151: Recliner Adjustment
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 If HIGH-level heating is selected, the system automati- WARNING! cally switches to LOW-level heating and turns one indi- • Persons who are unable to feel pain to the skin cator light OFF after a maximum of 60 minutes of continuous operation.
Page 152: Lumbar Support - If Equipped
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then lean back to the position desired and release the WARNING! lever. To return the seatback to its normal upright posi- • Adjusting a seat while the vehicle is moving is tion, lean forward and lift the lever. Release the lever once the seatback is in the upright position.
Page 153: Easy Entry System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Easy Entry System The Easy Entry lever is located on upper seat belt anchor cover. Lumbar Support Easy Entry Lever Pull the lever upward to move the seat and seatback forward.
Page 154: Adjusting Active Head Restraints
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When returning the seat to its normal position, the memory feature restores the seat position and seatback recline position to their current settings. On the driver seat, pull the lever upward to move the seatback forward.
Page 155 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Push Button Active Head Restraint (Normal Position) For comfort the Active Head Restraints can be tilted forward and backward. To tilt the head restraint closer to the back of your head, pull outward on the bottom of the head restraint.
Page 156 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In the event of deployment of an Active Head Re- straint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things to Know Before Starting Your Vehicle” for further information. WARNING! • Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision.
Page 157: To Open And Close The Hood
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 TO OPEN AND CLOSE THE HOOD WARNING! (Continued) Two latches must be released to open the hood. • Do not place items over the top of the Active Head 1. Pull the hood release lever located under the left side Restraint, such as coats, seat covers or portable of the instrument panel.
Page 158 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Move to the outside of the vehicle and lift the second- ary latch underneath the center front edge of the hood and raise the hood. Hood Prop Rod Hole Location Before closing the hood, make sure to stow the prop rod in its proper location.
Page 159: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 lights, turn signal lights, instrument panel lights, instru- CAUTION! ment panel light dimming, interior lights and fog lights (if equipped). To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage.
Page 160: Headlights And Parking Lights
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights And Parking Lights Lights-On Reminder Turn the end of the multifunction lever to the first detent If the headlights or parking lights are on after the ignition for parking light operation. Turn the end of the lever to is turned to the LOCK position, a chime will sound to the second detent for headlight operation.
Page 161: Headlights With Wipers (Available With Automatic Headlights Only)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Headlights With Wipers To activate the delay, turn the ignition switch to the (Available With Automatic Headlights Only) LOCK position while the headlights are still on. Then, When this feature is active, the headlights will turn on turn off the headlights within 45 seconds.
Page 162: Instrument Panel Dimmer
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Instrument Panel Dimmer Rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened. Rotate the center portion of the lever up to increase the brightness of the instrument panel lights when the park- ing lights or headlights are on.
Page 163: Daytime Running Lights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Daytime Running Lights — If Equipped The high beam headlights will turn on as Daytime Running Lights (DRL) and operate at lower intensity whenever the ignition is ON, the engine is running, the headlight switch is off, the parking brake is released and the shift lever is in any position except PARK.
Page 164: Turn Signals
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Lane Change Assist Move the multifunction lever up or down and the arrows Tap the lever up or down once, without moving beyond on each side of the instrument cluster flash to show the detent, and the turn signal (right or left) will flash proper operation of the front and rear turn signal lights.
Page 165: Interior Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Interior Lights A courtesy light is also found in the rear of the center Two courtesy/reading lights are located in the bottom of console. You can turn this light on and off from the the rearview mirror.
Page 166: Windshield Wipers And Washers
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column. Changing Wiper Speeds NOTE: The wipers will automatically return to the “Park” position if you turn the ignition switch OFF while they are operating.
Page 167: Intermittent Wiper System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 regulate the wipe interval from a minimum of one cycle CAUTION! every second to a maximum of approximately 18 seconds • Turn the windshield wipers off when driving between cycles. through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off.
Page 168: Mist Feature
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The mist feature does not activate the washer WARNING! pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to Sudden loss of visibility through the windshield spray the windshield with washer fluid.
Page 169: Headlights With Wipers (Available With Auto Headlights Only)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Headlights With Wipers Windshield Washers (Available With Auto Headlights Only) To use the washer, pull the windshield wiper/washer When this feature is active, the headlights will turn on control lever toward you and hold it for as long as approximately 10 seconds after the wipers are turned on washer spray is desired.
Page 170: Tilt/Telescoping Steering Column
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT/TELESCOPING STEERING COLUMN To unlock the steering column, push the lever down- This feature allows you to tilt the steering column ward. To tilt the steering column, move the steering upward or downward. It also allows you to lengthen or wheel upward or downward as desired.
Page 171: Electronic Speed Control - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, the Electronic Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h). The Electronic Speed Control buttons are located on the right side of the steering wheel.
Page 172: To Activate
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE System can be reactivated by pushing the Electronic To Set A Desired Speed Speed Control ON/OFF button and resetting the desired Turn the Electronic Speed Control ON. When the vehicle vehicle set speed. has reached the desired speed, press the SET (-) button and release.
Page 173: To Resume Speed
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 To Resume Speed decrease until the button is released. Release the button To resume a previously set speed, push the RES (+) when the desired speed is reached, and the new set speed button and release.
Page 174: Garage Door Opener - If Equipped
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE On steep hills, a greater speed loss or gain may occur so The HomeLink buttons that are located in the headliner it may be preferable to drive without Electronic Speed or sun visor designate the three different HomeLink Control.
Page 175: Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 Programming HomeLink WARNING! Before You Begin • Your motorized door or gate will open and close If you have not trained any of the HomeLink buttons, while you are training the universal transceiver. erase all channels before you begin training.
Page 176 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After training a HomeLink channel, if the garage Place the handheld transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink button you wish to program while door does not operate with HomeLink and the ga- keeping the indicator light in view.
Page 177 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 This can usually be found where the hanging antenna 6. Firmly press and release the LEARN or TRAINING wire is attached to the garage door opener motor. It is button. The name and color of the button may vary by NOT the button normally used to open and close the manufacturer.
Page 178: Gate Operator/Canadian Programming
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming transmitter every two seconds until HomeLink has Canadian radio frequency laws require transmitter sig- successfully accepted the frequency signal. The indica- nals to time-out (or quit) after several seconds of trans- tor light will flash slowly and then rapidly when fully mission –...
Page 179: Reprogramming A Single Homelink Button
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 Reprogramming A Single HomeLink Button The HomeLink Universal Transceiver is disabled when To reprogram a channel that has been previously trained, the Vehicle Security Alarm is active. follow these steps: Troubleshooting Tips 1. Turn the ignition switch to the ON/RUN position. If you are having trouble programming HomeLink , here are some of the most common solutions: 2.
Page 180: General Information
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information ELECTRICAL POWER OUTLETS This device complies with FCC rules Part 15 and Industry There are two 12 Volt (13 Amp) electrical power outlets Canada RSS-210. Operation is subject to the following on this vehicle.
Page 181 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 Instrument Panel Power Outlet Center Console The center console power outlet is powered directly from the battery (power available at all times). Items plugged into this power outlet may discharge the battery and/or prevent the engine from starting.
Page 182 180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. •...
Page 183: Cigar Lighter And Ash Receiver - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 CIGAR LIGHTER AND ASH RECEIVER — IF CAUTION! EQUIPPED • Many accessories that can be plugged in draw An optional ash receiver is available from your autho- rized dealer and will fit in the center console front power from the vehicle’s battery, even when not in cupholder.
Page 184: Cupholders
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS Rear Seat Cupholders Cupholders for the rear seat occupants are located in the Front Seat Cupholder armrests. Each cupholder is capable of holding up to a The cupholder in the center console will accommodate 20 oz.
Page 185: Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 WARNING! If containers of hot liquid are place in the cupholder, they can spill when the door is closed, burning the occupants. Be careful when closing the doors to avoid injury. STORAGE Glove Box Storage Compartment The glove box storage compartment is located on the right side of the instrument panel.
Page 186 184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE is also equipped with an electrical power outlet. Refer to “Power Outlets” in “Understanding The Feature of Your Vehicle” for further information. Center Console Storage The top compartment holds small items, such as a pen and note pad, while the larger bottom compartment will hold CDs and alike.
Page 187: Cargo Area Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 NOTE: CARGO AREA FEATURES • A notch in the front of the console base allows for use The 60/40 split-folding rear seat provides cargo-carrying of a cellular phone while it is plugged into the power versatility.
Page 188 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • To help protect against personal injury, passengers • Be certain that the seatback is securely locked into should not be seated in the rear cargo area. The position. If the seatback in not securely locked rear cargo space is intended for load carrying into position, the seat will not provide the proper purposes only, not for passengers, who should sit...
Page 189: Ski Pass-Through
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or become a dan- gerous projectile in a sudden stop or collision. Ski Pass-Through There is a ski pass-through door located behind the rear seat armrest that allows longer items, such as snow skis, to be stored in the rear cargo area.
Page 190: Rear Window Features
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES CAUTION! Rear Window Defroster Failure to follow these cautions can cause damage to The rear window defroster button is located on the the heating elements: climate control (Mode) knob. Press this button to •...
Page 191 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....192 Trip Functions ..... . 214 Instrument Cluster .
Page 192 190 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (Disc Mode For CD Media Center 130 (Sales Code RES) ..242 And MP3/WMA Audio Play, DVD-Video) . . . 230 Operating Instructions — Radio Mode ..242 Notes On Playing MP3/WMA Files .
Page 193 UNDERSTANDING YOUR INSTRUMENT PANEL 191 Uconnect™ Multimedia (Satellite Radio) — Steering Wheel Audio Controls — If Equipped ......262 If Equipped .
Page 194: Instrument Panel Features
192 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 — Air Outlet 6 — Radio 11 — Storage Compartment 2 — Side Window Demister Outlet 7 — Passenger Airbag 12 — Climate Control 3 — Instrument Cluster 8 — Glove Compartment 13 —...
Page 195: Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 193 INSTRUMENT CLUSTER...
Page 196: Instrument Cluster Descriptions
194 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS removes this heat. You can also turn the Temperature control to maximum heat, the Mode control to Floor and 1. Temperature Gauge the Fan control to High. This allows the heater core to act The temperature gauge shows engine coolant tempera- as a supplement to the radiator and aids in removing heat ture.
Page 197 UNDERSTANDING YOUR INSTRUMENT PANEL 195 5. Low Fuel Light If jump starting is required, refer to “Jump Starting When the fuel level drops to approximately 2.0 gal- Procedures” in “What To Do In Emergencies”. lons (7.6 Liters), the fuel symbol will light and a 7.
Page 198 196 UNDERSTANDING YOUR INSTRUMENT PANEL flash or remain on continuously. Refer to “Occupant 10. Engine Temperature Warning Light Restraints” in “Things To Know Before Starting Your This light warns of an overheated engine condi- Vehicle” for further information. tion. As temperatures rise and the gauge ap- proaches H, this indicator will illuminate and a 9.
Page 199 UNDERSTANDING YOUR INSTRUMENT PANEL 197 11. Brake Warning Light If brake failure is indicated, immediate repair is neces- This light monitors various brake functions, sary. including brake fluid level and parking brake WARNING! application. If the brake light turns on it may indicate that the parking brake is applied, that Driving a vehicle with the brake light on is danger- the brake fluid level is low, or that there is a problem with...
Page 200 198 UNDERSTANDING YOUR INSTRUMENT PANEL The operation of the Brake Warning Light can be checked 13. Shift Lever Indicator by turning the ignition switch from the OFF position to The Shift Lever Indicator is self-contained within the the ON/RUN position. The light should illuminate for instrument cluster.
Page 201 UNDERSTANDING YOUR INSTRUMENT PANEL 199 reading before the repair/service, so that you can be sure Vehicle Odometer Messages that it is properly reset, or that the door jamb sticker is When the appropriate conditions exist, the odometer will accurate if the odometer must be reset at zero. display the following messages: door .
Page 202 200 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the instrument cluster is equipped with the HOTOIL optional Electronic Vehicle Information Center (EVIC), When this message is displayed there is a transmission then all warnings including ”Low Tire,” “Door Ajar” and over-temperature condition. When this condition occurs, “Trunk Ajar”...
Page 203 UNDERSTANDING YOUR INSTRUMENT PANEL 201 the problem continues, the message will appear the next the oil change indicator system (after performing the time the vehicle is started. See your authorized dealer scheduled maintenance) perform the following proce- service center as soon as possible. dure: CHANgE OIL 1.
Page 204 202 UNDERSTANDING YOUR INSTRUMENT PANEL 15. Cruise Indicator — If Equipped 17. Electronic Throttle Control (ETC) Indicator Light This indicator shows that the Electronic Speed This light informs you of a problem with the Control System is ON. Electronic Throttle Control (ETC) system. If a problem is detected, the light will come on 16.
Page 205 UNDERSTANDING YOUR INSTRUMENT PANEL 203 18. Park/Headlight ON Indicator — If Equipped 21. Front Fog Light Indicator — If Equipped This indicator will illuminate when the park This indicator will illuminate when the front fog lights or headlights are turned on. lights are on.
Page 206 204 UNDERSTANDING YOUR INSTRUMENT PANEL the conventional brake system will continue to operate engine running. If the “ESC Activation/Malfunction In- normally provided that the BRAKE warning light is not dicator Light” comes on continuously with the engine running, a malfunction has been detected in the ESC system.
Page 207 UNDERSTANDING YOUR INSTRUMENT PANEL 205 • The ESC system will make buzzing or clicking sounds As an added safety feature, your vehicle has been when it is active. This is normal; the sounds will stop equipped with a Tire Pressure Monitoring System when ESC becomes inactive following the maneuver (TPMS) that illuminates a low tire pressure telltale when that caused the ESC activation.
Page 208 206 UNDERSTANDING YOUR INSTRUMENT PANEL Your vehicle has also been equipped with a TPMS CAUTION! malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is The TPMS has been optimized for the original combined with the low tire pressure telltale. When the equipment tires and wheels.
Page 209 UNDERSTANDING YOUR INSTRUMENT PANEL 207 the bulb does not come on when turning the key from WARNING! LOCK to ON/RUN, have the condition checked promptly. A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal Certain conditions, such as a loose or missing gas cap, operating conditions.
Page 210: Mini-Trip Computer - If Equipped
208 UNDERSTANDING YOUR INSTRUMENT PANEL 29. Electronic Vehicle Information Center (EVIC) CAUTION! Display — If Equipped This display shows the EVIC messages when the appro- Continuous driving with the Transmission Tempera- priate conditions exist. Refer to “Electronic Vehicle Infor- ture Warning Light illuminated will eventually cause mation Center (EVIC)”...
Page 211: Control Buttons
UNDERSTANDING YOUR INSTRUMENT PANEL 209 Control Buttons RESET Button To reset the display shown, turn the ignition switch to the ON position, then press and hold the RESET button located on the steering wheel. The following displays can be reset or changed: •...
Page 212: Electronic Vehicle Information Center (Evic) - If Equipped
210 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER The EVIC consists of the following: (EVIC) – IF EQUIPPED • System Status The Electronic Vehicle Information Center (EVIC) fea- • Vehicle Information Warning Message Displays tures a driver-interactive display that is located in the instrument cluster.
Page 213 UNDERSTANDING YOUR INSTRUMENT PANEL 211 The system allows the driver to select information by Press and release the MENU button to advance pressing the following buttons mounted on the steering the display to Trip Functions or Personal Set- wheel: tings or to return to the default System Status display.
Page 214: Electronic Vehicle Information Center (Evic) Displays
212 UNDERSTANDING YOUR INSTRUMENT PANEL • RKE (Remote Keyless Entry) Battery Low (with a Press and release the SELECT Button to accept a selection. The SELECT Button also resets single chime) various Trip Functions. • Personal Settings Not Available – Vehicle Not in Park SELECT •...
Page 215: Oil Change Required - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 213 • Remote start aborted — Fuel low Oil Change Required — If Equipped Your vehicle is equipped with an engine oil change • Remote start disabled — System fault indicator system. The “Oil Change Required” message •...
Page 216: Trip Functions
214 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Fully depress the accelerator pedal slowly three times Press and release the DOWN button to advance the within 10 seconds. display through the Trip Functions. 3. Turn the ignition switch to the LOCK position. The Trip Functions mode displays the following informa- tion: NOTE: If the indicator message illuminates when you...
Page 217 UNDERSTANDING YOUR INSTRUMENT PANEL 215 • Distance To Empty (DTE) • Elapsed Time Shows the estimated distance that can be traveled with Shows the total elapsed time of travel since the last reset. the fuel remaining in the tank. This estimated distance is Elapsed time will increment when the ignition switch is determined by a weighted average of the instantaneous in the ON or START position.
Page 218: Compass Display
216 UNDERSTANDING YOUR INSTRUMENT PANEL Compass Display one or more 360° turns (in an area free from large metal The compass heading indicates the direction or metallic objects) until the CAL indicator in the EVIC the vehicle is facing. Press and release the turns off.
Page 219 UNDERSTANDING YOUR INSTRUMENT PANEL 217 4. Press and release the SELECT Button and the CAL indicator will quit flashing. 5. Drive the vehicle slowly, completing one or more circles (in an area free from large metal or metallic objects) until the CAL indicator turns off. The compass will now function normally.
Page 220: Personal Settings (Customer-Programmable Features)
218 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Press and release the DOWN button until “Compass Press and release the MENU button until “Personal Variance” and the current Variance Value displays in the Settings” displays in the EVIC. EVIC. Press and release the DOWN button to display the 4.
Page 221 UNDERSTANDING YOUR INSTRUMENT PANEL 219 RKE Unlock Flash Lamps with LOCK When Driver Door 1st Press is selected, only the driver’s When ON is selected, the front and rear turn signals will door will unlock on the first press of the Remote Keyless flash when the doors are locked or unlocked with the Entry (RKE) transmitter UNLOCK button.
Page 222 220 UNDERSTANDING YOUR INSTRUMENT PANEL off if they were turned on by this feature. To make your Illumin. Approach selection, press the SELECT button until ON or OFF When this feature is selected, the headlights will activate appears. and remain on for up to 90 seconds when the doors are unlocked with the remote keyless entry transmitter.
Page 223: Setting The Analog Clock
UNDERSTANDING YOUR INSTRUMENT PANEL 221 Display Units In SETTING THE ANALOG CLOCK The EVIC and odometer can be changed between English and Metric units of measure. To make your selection, press and release the SELECT button until “ENGLISH” or “METRIC” appears. Calibrate Compass Refer to “Compass Display”...
Page 224: Media Center 230 (Req) - Am/Fm Stereo Radio And 6-Disc Cd/Dvd Changer (Mp3/Wma Aux Jack)
222 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 230 (REQ) — AM/FM STEREO Operating Instructions - Radio Mode RADIO AND 6–DISC CD/DVD CHANGER NOTE: The ignition switch must be in the ON or ACC (MP3/WMA AUX JACK) position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate.
Page 225 UNDERSTANDING YOUR INSTRUMENT PANEL 223 to seek up and the left switch to seek down. The radio If your vehicle is not equipped with or this feature is not will remain tuned to the new station until you make available on your vehicle, a “Not Equipped With another selection.
Page 226 224 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure INFO Button Press the INFO button for an RDS station (one with call 1. Press and hold the TIME button until the hours blink. letters displayed). The radio will return a Radio Text 2.
Page 227 UNDERSTANDING YOUR INSTRUMENT PANEL 225 Push the rotary TUNE/SCROLL control knob a second MUSIC TYPE Button time and MID will display. Turn the TUNE/SCROLL Pressing this button once will turn on the Music Type control knob to the right or left to increase or decrease the mode for five seconds.
Page 228 226 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type 16-Digit Character Display Program Type 16-Digit Character Display Information Inform Top 40 Top 40 Jazz Jazz Weather Weather News News By pressing the SEEK button when the Music Type icon Nostalgia Nostalga is displayed, the radio will be tuned to the next frequency Oldies Oldies station with the same selected Music Type name.
Page 229 UNDERSTANDING YOUR INSTRUMENT PANEL 227 • DVD Enter - When the disc is in DVD Menu mode, • Angle – Repeatedly pressing SELECT will change selecting DVD Enter will allow you to play the current the viewing angle if supported by the DVD disc (if highlighted selection.
Page 230 228 UNDERSTANDING YOUR INSTRUMENT PANEL • Set Home Clock - Pressing the SELECT button allows Audio Language — If Equipped you to set the clock. Turn the TUNE/SCROLL control Selecting this item allows you to choose a default audio knob to adjust the hours and then press and turn the language (effective only if the language is supported by TUNE/SCROLL control knob to adjust the minutes.
Page 231 UNDERSTANDING YOUR INSTRUMENT PANEL 229 Audio DRC — If Equipped NOTE: The user will have to set these defaults before Selecting this item allows you to limit maximum audio loading a disc. If changes are made to these settings after dynamic range.
Page 232: Operation Instructions - (Disc Mode For Cd And Mp3/Wma Audio Play, Dvd-Video)
230 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by Operation Instructions - (DISC MODE for CD and repeating the above procedure with this exception: Press MP3/WMA Audio Play, DVD-VIDEO) the SET button twice and SET 2 will show in the display The radio DVD player and many DVD discs are coded by window.
Page 233 UNDERSTANDING YOUR INSTRUMENT PANEL 231 NOTE: The ignition switch must be in the ON or ACC Eject Button — Ejecting Compact Disc(s) position to operate the radio. Press the EJECT button and the pushbutton with the corresponding number (1-6) where the LOAD Button —...
Page 234: Notes On Playing Mp3/Wma Files
232 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (CD MODE) Notes On Playing MP3/WMA Files Press the SCAN button to scan through each track on the The radio can play MP3/WMA files; however, acceptable CD currently playing. MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the TIME Button (CD MODE) following restrictions.
Page 235 UNDERSTANDING YOUR INSTRUMENT PANEL 233 The radio uses the following limits for file systems: If a disc contains multi-formats, such as CD audio and MP3/WMA tracks, the radio will only play the MP3/ • Maximum number of directory levels: 8 WMA tracks on that disc.
Page 236 234 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3/WMA Files MPEG Sampling Fre- Bit Rate (kbps) When a medium containing MP3/WMA data is loaded, Specification quency (kHz) the radio checks all files on the medium. If the medium 320, 256, 224, contains a lot of folders or files, the radio will take more MPEG-1 Audio 192, 160, 128,...
Page 237: List Button (Disc Mode For Mp3/Wma Play)
UNDERSTANDING YOUR INSTRUMENT PANEL 235 LIST Button (DISC Mode for MP3/WMA Play) Press and hold the INFO button again for three seconds Pressing the LIST button will bring up a list of all folders to return to elapsed time display. on the disc.
Page 238: If Equipped
236 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Auxiliary Mode) Operating Instructions — Voice Command System No function. (If Equipped) For the radio, Refer to “Voice Command” in the EJECT Button (Auxiliary Mode) Uconnect™ User Manual located on the DVD for further No function.
Page 239 UNDERSTANDING YOUR INSTRUMENT PANEL 237 Macrovision Radio. This service offers over 130 channels of music, This product incorporates copyright protection technol- sports, news, entertainment, and programming for chil- ogy that is protected by U.S. patents and other intellec- dren, directly from its satellites and broadcasting studios. tual property rights.
Page 240 238 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Serial Number/Sirius Identification Selecting Uconnect™ Multimedia (Satellite) Mode Number (ESN/SID) Press the SAT button until SAT appears in the display. A Please have the following information available when CD may remain in the radio while in the Satellite radio calling: mode.
Page 241 UNDERSTANDING YOUR INSTRUMENT PANEL 239 • Dense tree coverage may interrupt reception in the SCAN Button form of short audio mutes. Pressing the SCAN button causes the tuner to search for the next channel, pausing for eight seconds before con- •...
Page 242 240 UNDERSTANDING YOUR INSTRUMENT PANEL TUNE Control (Rotary) SETUP Button Turn the rotary TUNE/SCROLL control knob clockwise Pressing the SETUP button allows you to select the to increase or counterclockwise to decrease the channel. following items: • Display Sirius ID number — Press the AUDIO/ MUSIC TYPE Button Pressing this button once will turn on the Music Type SELECT button to display the Sirius ID number.
Page 243: If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 241 You may add a second channel to each pushbutton by MEDIA CENTER 730N/430/430N (RHR/RER/RBZ/ repeating the above procedure with this exception: Press RHB) CD/DVD/HDD/NAV — IF EQUIPPED the SET button twice and SET 2 will show in the display NOTE: The sales code is located on the lower right side window.
Page 244: Media Center 130 (Sales Code Res)
242 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 130 (SALES CODE RES) Operating Instructions — Radio Mode NOTE: The radio sales code is located on the lower right NOTE: The ignition switch must be in the ON or ACC side of the radio faceplate. position to operate the radio.
Page 245 UNDERSTANDING YOUR INSTRUMENT PANEL 243 SEEK Buttons 4. Adjust the minutes using the right side TUNE/ Press and release the SEEK buttons to search for the next SCROLL control knob. Press the TUNE/SCROLL control listenable station in AM/FM mode. Press the right switch knob to save time change.
Page 246 244 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second AM/FM Button time and MID will display. Turn the TUNE/SCROLL Press the buttons to select either AM or FM mode. control knob to the right or left to increase or decrease the SET/RND Button —...
Page 247: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
UNDERSTANDING YOUR INSTRUMENT PANEL 245 • This radio is capable of playing compact discs (CD), and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by recordable compact discs (CD-R), rewritable compact pressing the pushbutton twice.
Page 248 246 UNDERSTANDING YOUR INSTRUMENT PANEL If you have ejected a disc and have not removed it within CAUTION! 10 seconds, it will be reloaded. If the CD is not removed, • This CD player will accept 4-3/4 in (12 cm) discs the radio will reinsert the CD but will not play it.
Page 249: Notes On Playing Mp3 Files
UNDERSTANDING YOUR INSTRUMENT PANEL 247 RW/FF Notes on Playing MP3 Files Press and hold the FF (Fast Forward) button and the CD The radio can play MP3 files; however, acceptable MP3 player will begin to fast forward until FF is released, or file recording media and formats are limited.
Page 250 248 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of files: 255 Discs created with an option such as keep disc open after writing are most likely multisession discs. The use of • Maximum number of folders. (The radio display of file multisession for CD audio or MP3 playback may result in names and folder names is limited.
Page 251 UNDERSTANDING YOUR INSTRUMENT PANEL 249 Playback of MP3 Files MPEG Sampling Fre- Bit Rate (kbps) When a medium containing MP3 data is loaded, the Specification quency (kHz) radio checks all files on the medium. If the medium 320, 256, 224, contains a lot of folders or files, the radio will take more MPEG-1 Audio 192, 160, 128,...
Page 252: Operation Instructions - Auxiliary Mode
250 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode MEDIA CENTER 130 WITH SATELLITE RADIO The auxiliary (AUX) jack is an audio input jack, which (SALES CODE RES+RSC) allows the user to plug in a portable device, such as an NOTE: The radio sales code is located on the lower right MP3 player, or cassette player, and utilize the vehicle’s side of the radio faceplate.
Page 253: Operating Instructions - Radio Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 251 Operating Instructions — Radio Mode to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make NOTE: The ignition switch must be in the ON or ACC another selection.
Page 254 252 UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button Uconnect™ Phone — If Equipped 3. After adjusting the hours, press the right side TUNE/ Press this button to operate the Uconnect™ Phone feature SCROLL control knob to set the minutes. The minutes (if equipped).
Page 255 UNDERSTANDING YOUR INSTRUMENT PANEL 253 INFO Button Push the rotary TUNE/SCROLL control knob a second Press the INFO button for an RDS station (one with call time and MID will display. Turn the TUNE/SCROLL letters displayed). The radio will return a Radio Text control knob to the right or left to increase or decrease the message broadcast from an FM station (FM mode only).
Page 256 254 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob again to Program Type 16-Digit Character Display exit setting tone, balance, and fade. College College MUSIC TYPE Button Country Country Pressing this button once will turn on the Music Type Foreign Language Language mode for five seconds.
Page 257 UNDERSTANDING YOUR INSTRUMENT PANEL 255 SETUP Button Program Type 16-Digit Character Display Pressing the SETUP button allows you to select between Soft Rhythm and Blues Soft R&B the following items: Sports Sports • Set Clock — Pressing the SELECT button will allow Talk Talk you to set the clock.
Page 258: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
256 UNDERSTANDING YOUR INSTRUMENT PANEL window. Select the button (1–6) you wish to lock onto this Buttons 1 - 6 station and press and release that button. If a button is These buttons tune the radio to the stations that you not selected within five seconds after pressing the SET/ commit to pushbutton memory (12 AM and 12 FM RND button, the station will continue to play but will not...
Page 259 UNDERSTANDING YOUR INSTRUMENT PANEL 257 Inserting Compact Disc(s) CAUTION! (Continued) Gently insert one CD into the CD player with the CD • Do not use adhesive labels. These labels can peel label facing up. The CD will automatically be pulled into away and jam the player mechanism.
Page 260 258 UNDERSTANDING YOUR INSTRUMENT PANEL A disc can be ejected with the radio and ignition OFF. RW/FF Press and hold FF (Fast Forward) and the CD player will NOTE: Ejecting with the ignition OFF is not allowed on begin to fast forward until FF is released or RW or convertible or soft-top models (if equipped).
Page 261: Notes On Playing Mp3 Files
UNDERSTANDING YOUR INSTRUMENT PANEL 259 • Maximum number of files: 255 Notes On Playing MP3 Files The radio can play MP3 files; however, acceptable MP3 • Maximum number of folders. (The radio display of file file recording media and formats are limited. When names and folder names is limited.
Page 262 260 UNDERSTANDING YOUR INSTRUMENT PANEL Discs created with an option such as keep disc open after MPEG Sampling Fre- Bit Rate (kbps) writing are most likely multisession discs. The use of Specification quency (kHz) multisession for CD audio or MP3 playback may result in 320, 256, 224, longer disc loading times.
Page 263: List Button (Cd Mode For Mp3 Play)
UNDERSTANDING YOUR INSTRUMENT PANEL 261 Playback of MP3 Files LIST Button (CD Mode for MP3 Play) When a medium containing MP3 data is loaded, the Pressing the LIST button will bring up a list of all folders radio checks all files on the medium. If the medium on the disc.
Page 264: Uconnect™ Multimedia (Satellite Radio) - If Equipped
262 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds TIME Button (Auxiliary Mode) to return to elapsed time display. Press this button to change the display to time of day. The time of day will display for five seconds (when the Operation Instructions - Auxiliary Mode ignition is OFF).
Page 265 UNDERSTANDING YOUR INSTRUMENT PANEL 263 radio system in your vehicle. Sirius will supply a wel- using the TUNE/SCROLL control knob until Sirius ID is come kit that contains general information, including selected. Press the TUNE/SCROLL control knob and the how to setup your on-line listening account. For further Sirius ID number will display.
Page 266 264 UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality SEEK Buttons Satellite reception may be interrupted due to one of the Press and release the SEEK buttons to search for the next following reasons: channel in Satellite mode. Press the right switch to seek up and the left switch to seek down.
Page 267 UNDERSTANDING YOUR INSTRUMENT PANEL 265 additional three seconds will make the radio display the Toggle the MUSIC TYPE button again to select the music Song Title all of the time (press and hold again to return type. to normal display). By pressing the SEEK button when the Music Type RW/FF function is active, the radio will be tuned to the next...
Page 268: Ipod /Usb/Mp3 Control - If Equipped
266 UNDERSTANDING YOUR INSTRUMENT PANEL SET Button – To Set the Pushbutton Memory Every time a preset button is used, a corresponding When you are receiving a channel that you wish to button number will display. commit to pushbutton memory, press the SET button. Buttons 1 - 6 The symbol SET 1 will now show in the display window.
Page 269: Connecting The Ipod Or External Usb Device
UNDERSTANDING YOUR INSTRUMENT PANEL 267 This feature allows an iPod or external USB device to be Connecting The iPod Or External USB Device plugged into the USB port, located in the center of the Use the connection cable to connect an iPod or external instrument panel below the climate controls.
Page 270: Using This Feature
268 UNDERSTANDING YOUR INSTRUMENT PANEL • The audio device can be controlled using the radio Once the audio device is connected and synchronized to the vehicle’s iPod /USB/MP3 control system (iPod or buttons to Play, Browse, and List the iPod contents. external USB device may take a few minutes to connect), •...
Page 271 UNDERSTANDING YOUR INSTRUMENT PANEL 269 • A single press backward << RW or forward FF >> will mode. In Play mode, the following buttons on the radio faceplate may be used to control the iPod or external jump backward or forward respectively, for five USB device and display data: seconds.
Page 272: List Or Browse Mode
270 UNDERSTANDING YOUR INSTRUMENT PANEL • Press the SCAN button to use iPod /USB/MP3 de- List Or Browse Mode vice scan mode, which will play the first 10 seconds of During Play mode, pressing any of the buttons described each track in the current list and then forward to the below, will bring up List mode.
Page 273 UNDERSTANDING YOUR INSTRUMENT PANEL 271 • During all List modes, the iPod displays all lists in • Pressing a PRESET button will display the current “wrap-around” mode. So if the track is at the list on the top line and the first item in that list on bottom of the list, just turn the wheel backward the second line.
Page 274: Bluetooth Streaming Audio (Btsa)
272 UNDERSTANDING YOUR INSTRUMENT PANEL Bluetooth Streaming Audio (BTSA) CAUTION! Music can be streamed from your cellular phone to the • Leaving the iPod or external USB device (or any Uconnect™ phone system. supported device) anywhere in the vehicle in Controlling BTSA Using Radio Buttons extreme heat or cold can alter the operation or To get into the BTSA mode, press either “AUX”...
Page 275: Steering Wheel Audio Controls - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 273 2. After the Ready prompt and the following beep, say STEERING WHEEL AUDIO CONTROLS — IF Setup , then Select Audio Devices . EQUIPPED 3. Say the name of the audio device or ask the Uconnect™...
Page 276: Radio Operation
274 UNDERSTANDING YOUR INSTRUMENT PANEL The right-hand rocker switch has a pushbutton in the The button located in the center of the left-hand switch center, and controls the volume and mode of the sound will tune to the next preset station that you have pro- system.
Page 277: Cd/Dvd Disc Maintenance
UNDERSTANDING YOUR INSTRUMENT PANEL 275 CD/DVD DISC MAINTENANCE NOTE: If you experience difficulty in playing a particu- To keep a CD/DVD in good condition, take the following lar disc, it may be damaged (i.e., scratched, reflective precautions: coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding.
Page 278: Manual Heating And Air Conditioning
276 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Heating And Air Conditioning Blower Control Rotate this control to regulate the amount of air forced through the ven- tilation system in any mode. The blower speed increases as you move the control to the right from the “O” (OFF) position.
Page 279 UNDERSTANDING YOUR INSTRUMENT PANEL 277 Temperature Control Mode Control (Air Direction) Rotate this control to regulate the tem- Rotate this control to choose from sev- perature of the air inside the passenger eral patterns of air distribution. You compartment. Rotating the dial left can select either a primary mode as into the blue area of the scale indicates identified by the symbols on the con-...
Page 280 278 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: For all settings, except full cold or full hot, there Defrost is a difference in temperature between the upper and Air is directed through the windshield and side lower outlets. The warmer air flows to the floor outlets. window demist outlets.
Page 281 UNDERSTANDING YOUR INSTRUMENT PANEL 279 the LED in the control button to illuminate. After ten several times then go out. Recirculation will be dis- minutes, the system will return to normal mode function abled automatically is these modes are selected. and the LED will turn off.
Page 282: Automatic Temperature Control (Atc) - If Equipped
280 UNDERSTANDING YOUR INSTRUMENT PANEL • MAX A/C Automatic Temperature Control (ATC) — If For maximum cooling use the A/C and recirculation Equipped buttons at the same time. • ECONOMY MODE If economy mode is desired, press the A/C button to turn OFF the indicator light and the A/C compressor.
Page 283 UNDERSTANDING YOUR INSTRUMENT PANEL 281 Automatic Operation the desired comfort level require air conditioning, the The Automatic Temperature Control system automati- system will automatically make the adjustment. cally maintains the climate in the cabin of the vehicle at You will experience the greatest efficiency by simply the comfort levels desired by the driver and passenger.
Page 284 282 UNDERSTANDING YOUR INSTRUMENT PANEL • If your air conditioning performance seems lower than Manual Operation expected, check the front of the A/C condenser located This system offers a full complement of manual override in front of the radiator for an accumulation of dirt or features, which consist of Blower Preferred Automatic, insects.
Page 285 UNDERSTANDING YOUR INSTRUMENT PANEL 283...
Page 286 284 UNDERSTANDING YOUR INSTRUMENT PANEL • Floor The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control Air is directed through the floor outlets with a knob (on the right) to one of the following positions. small amount flowing through the defrost and side window demist outlets.
Page 287 UNDERSTANDING YOUR INSTRUMENT PANEL 285 • Air Conditioner Control NOTE: • When the ignition switch is turned to the LOCK Press this button to turn on the air conditioning during manual operation position, the recirculation feature will be cancelled. only. When the air conditioning is •...
Page 288: Operating Tips
286 UNDERSTANDING YOUR INSTRUMENT PANEL • Most of the time, when in Automatic Operation, you Summer Operation can temporarily put the system into Recirculation The engine cooling system in air-conditioned vehicles Mode by pressing the Recirculation button. However, must be protected with a high-quality antifreeze coolant under certain conditions, while in Automatic Mode, to provide proper corrosion protection and to protect the system is blowing air out the defrost vents.
Page 289 UNDERSTANDING YOUR INSTRUMENT PANEL 287 Window Fogging Outside Air Intake Interior fogging on the windshield can be quickly re- Make sure the air intake, located directly in front of the moved by turning the mode selector to Defrost. The Mix windshield, is free of obstructions such as leaves.
Page 290 288 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions for Various Weather Conditions...
Page 291: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ....294 Automatic Transmission ....297 Automatic Transmission .
Page 292 290 STARTING AND OPERATING General Information ....305 Traction Control System (TCS) ... 315 Driving On Slippery Surfaces .
Page 293 STARTING AND OPERATING 291 Tire Inflation Pressures ....333 Tire Rotation Recommendations ... 342 Radial-Ply Tires ..... 335 Tire Pressure Monitor System (TPMS) .
Page 294 292 STARTING AND OPERATING Flexible Fuel (3.6L Engine Only) — Adding Fuel ......361 If Equipped ......357 Fuel Filler Cap (Gas Cap) .
Page 295 STARTING AND OPERATING 293 Trailer Towing Weights Recreational Towing (Maximum Trailer Weight Ratings) ..369 (Behind Motorhome, Etc.) ....376 Trailer And Tongue Weight .
Page 296: Starting Procedures
294 STARTING AND OPERATING STARTING PROCEDURES Automatic Transmission Before starting your vehicle, adjust your seat, adjust the The shift lever must be in the PARK or NEUTRAL inside and outside mirrors, fasten your seat belt, and if position before you can start the engine. Apply the brakes present, instruct all other occupants to buckle their seat before shifting to any driving gear.
Page 297: Extreme Cold Weather (Below -20°F Or 29°C)
STARTING AND OPERATING 295 For vehicles equipped with Tip Start (Six-Speed Trans- If Engine Fails To Start mission), turn the ignition switch to the START position WARNING! and release it as soon as the starter engages. The starter motor will continue to run, and it will disengage auto- •...
Page 298 296 STARTING AND OPERATING Without Tip Start If the engine shows no sign of starting after two 15- If the engine fails to start after you have followed the second periods of cranking with the accelerator pedal “Normal Starting” or “Extreme Cold Weather” proce- held to the floor, repeat the “Normal Starting”...
Page 299: After Starting
STARTING AND OPERATING 297 The engine block heater must be plugged in at least one CAUTION! hour to have an adequate warning effect on the engine. To prevent damage to the starter, wait 10 to 15 sec- WARNING! onds before trying again. Remember to disconnect the engine block heater After Starting cord before driving.
Page 300 298 STARTING AND OPERATING CAUTION! (Continued) WARNING! • Shift the shift lever into or out of REVERSE only • It is dangerous to move the shift lever out of PARK after the vehicle has come to a complete stop and or NEUTRAL if the engine speed is higher than the engine is at idle speed.
Page 301: Automatic Transmission Ignition Interlock Systems
STARTING AND OPERATING 299 Automatic Transmission Ignition Interlock WARNING! (Continued) Systems • Unintended movement of a vehicle could injure These systems prevent the key fob from being removed those in and near the vehicle. As with all vehicles, unless the shift lever is in PARK. They also prevent you should never exit a vehicle while the engine is shifting out of PARK unless the ignition switch is in the running.
Page 302: Brake/Transmission Interlock System
300 STARTING AND OPERATING Brake/Transmission Interlock System This vehicle is equipped with a Brake Transmission Shift Interlock System (BTSI) that holds the shift lever in the PARK position when the ignition switch is in the LOCK position. To move the shift lever out of the PARK position, the ignition switch must be turned to the ON or START position (engine running or not) and the brake pedal must be pressed.
Page 303 STARTING AND OPERATING 301 When parking on a flat surface, place the shift lever into WARNING! (Continued) the PARK position first, and then apply the parking • Never leave children alone in a vehicle. Leaving brake. unattended children in a vehicle is dangerous for a When parking on a hill, it is important to set the parking number of reasons.
Page 304 302 STARTING AND OPERATING NEUTRAL example: When operating the vehicle under heavy load- This range is used when vehicle is standing for pro- ing conditions, (i.e., in hilly terrain, traveling into strong longed periods with engine running. Engine may be headwinds, or while towing heavy trailers).
Page 305 STARTING AND OPERATING 303 DRIVE 3 — Four-Speed Transmission CAUTION! This range eliminates shifts into fourth gear. The trans- mission will operate normally in first and second gear. If the transmission operating temperature exceeds Shifts into third gear may be delayed to provide second acceptable limits, the vehicle computer may override gear operation at higher speeds.
Page 306: Autostick - If Equipped
304 STARTING AND OPERATING In the event of a momentary problem, the transmission AUTOSTICK — IF EQUIPPED can be reset to regain all forward gears by performing the AutoStick is a driver-interactive feature providing following steps: manual shift control, giving you more control of the vehicle.
Page 307: General Information
STARTING AND OPERATING 305 • Avoid using speed control when AutoStick is en- NOTE: In AutoStick mode, the transmission will only shift up or down when the driver moves the shift lever to gaged. the right (+) or left (-), or as described below. •...
Page 308: Driving On Slippery Surfaces
306 STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES Traction When driving on wet or slushy roads, it is possible for a Acceleration wedge of water to build up between the tire and road Rapid acceleration on snow covered, wet, or other slip- surface.
Page 309: Driving Through Water
STARTING AND OPERATING 307 DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure shallow standing water, consider the following Caution safety and prevent damage to your vehicle.
Page 310 308 STARTING AND OPERATING CAUTION! (Continued) WARNING! • Driving through standing water may cause dam- • Driving through standing water limits your vehi- age to your vehicle’s drivetrain components. Al- cle’s traction capabilities. Do not exceed 5 mph ways inspect your vehicle’s fluids (i.e., engine oil, (8 km/h) when driving through standing water.
Page 311: Power Steering
STARTING AND OPERATING 309 POWER STEERING system. This noise should be considered normal, and it The standard power steering system will give you good does not in any way damage the steering system. vehicle response and increased ease of maneuverability WARNING! in tight spaces.
Page 312: Parking Brake
310 STARTING AND OPERATING checked if a leak is suspected, abnormal noises are If necessary, add fluid to restore to the proper indicated apparent, and/or the system is not functioning as antici- level. With a clean cloth, wipe any spilled fluid from all pated.
Page 313 STARTING AND OPERATING 311 NOTE: • When the parking brake is applied and the transmis- sion is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle.
Page 314 312 STARTING AND OPERATING WARNING! WARNING! (Continued) • Be sure the parking brake is fully disengaged • Never use the PARK position as a substitute for before driving; failure to do so can lead to brake the parking brake. Always apply the parking failure and a collision.
Page 315: Anti-Lock Brake System (Abs)
STARTING AND OPERATING 313 ANTI-LOCK BRAKE SYSTEM (ABS) WARNING! (Continued) The Anti-Lock Brake System (ABS) provides increased • The ABS cannot prevent collisions, including vehicle stability and brake performance under most those resulting from excessive speed in turns, braking conditions. The system operates with a separate following another vehicle too closely, or hydro- computer to modulate the hydraulic pressure to prevent planing.
Page 316 314 STARTING AND OPERATING service is required. However, the conventional brake properly. This self check occurs each time the vehicle is system will continue to operate normally if the “Brake started and accelerated past 7 mph (11 km/h). Warning Light” is not on. ABS is activated during braking under certain road or If the “Anti-Lock Brake Warning Light”...
Page 317: Electronic Brake Control System
STARTING AND OPERATING 315 together to enhance vehicle stability and control in vari- WARNING! ous driving conditions and are commonly referred to as ESC. The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to Anti-Lock Brake System (ABS) interference caused by improperly installed or high This system aids the driver in maintaining vehicle control output radio transmitting equipment.
Page 318: Brake Assist System (Bas)
316 STARTING AND OPERATING spinning faster than the other, the system will apply the reduce brake pedal pressure unless braking is no longer brake of the spinning wheel. This will allow more engine desired. Once the brake pedal is released, the BAS is torque to be applied to the wheel that is not spinning.
Page 319: Hill Start Assist (Hsa) - If Equipped
STARTING AND OPERATING 317 Hill Start Assist (HSA) – If Equipped HSA Activation Criteria The HSA system is designed to assist the driver in The following criteria must be met in order for HSA to launching a vehicle on an incline. HSA will maintain the activate: level of brake pressure the driver inputs for a short •...
Page 320 318 STARTING AND OPERATING The system will only work if the intended direction of the 3. Apply the parking brake. vehicle and vehicle gear match. For example, if the 4. Start the engine. intended direction is forward up a hill and the vehicle is in DRIVE and the activation criteria are met, HSA will 5.
Page 321: Electronic Stability Control (Esc)
STARTING AND OPERATING 319 • Over-steer - when the vehicle is turning more than EVIC Equipped Vehicles HSA is a Customer Programmable Feature on a EVIC appropriate for the steering wheel position. equipped vehicle. If you wish to turn off the HSA feature, •...
Page 322 320 STARTING AND OPERATING ESC Operating Modes reduction. This mode is intended to be used if the vehicle All ESC equipped vehicles can choose the following ESC is in deep snow, sand, or gravel conditions and more operating modes: wheel spin than ESC would normally allow is required to gain traction.
Page 323: Esc Activation/Malfunction Indicator Light And Esc Off Indicator Light
STARTING AND OPERATING 321 To turn ESC on again, momentarily press the “ESC Off” ESC Activation/Malfunction Indicator Light And switch. This will restore the normal “ESC On” mode of ESC OFF Indicator Light operation. The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on WARNING! when the ignition switch is turned to the ON position.
Page 324: Tire Safety Information
322 STARTING AND OPERATING Malfunction Indicator Light” begins to flash during ac- TIRE SAFETY INFORMATION celeration, ease up on the accelerator and apply as little Tire Markings throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. NOTE: •...
Page 325 STARTING AND OPERATING 323 NOTE: tires is the same as for P-Metric tires except for the • P (Passenger) - Metric tire sizing is based on U.S. letters “LT” that are molded into the sidewall preced- design standards. P-Metric tires have the letter “P” ing the size designation.
Page 326 324 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm)
Page 327 STARTING AND OPERATING 325 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 328: Tire Identification Number (Tin)
326 STARTING AND OPERATING Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
Page 329: Tire Terminology And Definitions
STARTING AND OPERATING 327 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold Tire Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
Page 330: Tire Loading And Tire Pressure
328 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard Tire Placard Location...
Page 331 STARTING AND OPERATING 329 axles must not be exceeded. For further information on This placard tells you important information about GAWRs, vehicle loading, and trailer towing, refer to the: “Vehicle Loading” in this section. 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of...
Page 332 330 STARTING AND OPERATING 3. Subtract the combined weight of the driver and pas- NOTE: • The following table shows examples on how to calcu- sengers from XXX lbs or XXX kg. late total load, cargo/luggage, and towing capacities 4. The resulting figure equals the available amount of of your vehicle with varying seating configurations cargo and luggage load capacity.
Page 333 STARTING AND OPERATING 331...
Page 334: Tires - General Information
332 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
Page 335: Tire Inflation Pressures
STARTING AND OPERATING 333 Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the • Unequal tire pressures from one side of the ve- driver’s side B-Pillar. hicle to the other can cause the vehicle to drift to Some vehicles may have Supplemental Tire Pressure the right or left.
Page 336 334 STARTING AND OPERATING Tire pressures change by approximately 1 psi (7 kPa) per CAUTION! 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in After inspecting or adjusting the tire pressure, al- the winter.
Page 337: Radial-Ply Tires
STARTING AND OPERATING 335 Tire Pressures For High Speed Operation Radial-Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
Page 338: Spare Tire Matching Original Equipped Tire And Wheel - If Equipped
336 STARTING AND OPERATING Spare Tire Matching Original Equipped Tire and Do not install more than one non-matching temporary Wheel – If Equipped use spare tire/wheel on the vehicle at any given time. The spare tire of your vehicle is equivalent in look and CAUTION! function as the original equipment tire and wheel found on the front or rear axle of your vehicle.
Page 339: Full Size Spare - If Equipped
STARTING AND OPERATING 337 T, S = Temporary Spare Tire WARNING! Since this tire has limited tread life the original equip- Compact spares are for temporary emergency use ment tire should be repaired (or replaced) and reinstalled only. With these spares, do not drive more than on your vehicle at the first opportunity.
Page 340: Limited-Use Spare - If Equipped
338 STARTING AND OPERATING your original equipment tire, replace (or repair) the WARNING! original equipment tire and reinstall on the vehicle at the first opportunity. Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle Limited-Use Spare –...
Page 341: Tread Wear Indicators
STARTING AND OPERATING 339 Refer to “Freeing A Stuck Vehicle” in “What To Do In Emergencies” for further information. WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one.
Page 342: Life Of Tire
340 STARTING AND OPERATING Life Of Tire Replacement Tires The service life of a tire is dependent upon varying The tires on your new vehicle provide a balance of many factors including but not limited to: characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
Page 343: Tire Chains
STARTING AND OPERATING 341 WARNING! WARNING! (Continued) • Failure to equip your vehicle with tires having • Do not use a tire, wheel size or rating other than adequate speed capability can result in sudden tire that specified for your vehicle. Some combinations failure and loss of vehicle control.
Page 344: Snow Tires
342 STARTING AND OPERATING SNOW TIRES poorer than that of non-studded tires. Some states pro- Some areas of the country require the use of snow tires hibit studded tires; therefore, local laws should be during the winter. All season tires can be identified by the checked before using these tire types.
Page 345: Tire Pressure Monitor System (Tpms)
STARTING AND OPERATING 343 The suggested rotation method is the “rearward cross” TIRE PRESSURE MONITOR SYSTEM (TPMS) shown in the following diagram. This rotation pattern The Tire Pressure Monitor System (TPMS) will warn the does not apply to some directional tires that must not be driver of a low tire pressure based on the vehicle recom- reversed.
Page 346 344 STARTING AND OPERATING The TPM System will warn the driver of a low tire For example, your vehicle may have a recommended pressure if the tire pressure falls below the low-pressure cold (parked for more than three hours) placard pressure warning limit for any reason, including low temperature of 30 psi (207 kPa).
Page 347 STARTING AND OPERATING 345 NOTE: CAUTION! • The TPMS is not intended to replace normal tire care • The TPMS has been optimized for the original and maintenance, or to provide warning of a tire failure or condition. equipment tires and wheels. TPMS pressures and warning have been established for the tire size •...
Page 348: Base System
346 STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, Tire Pressure Monitoring Low Pressure Warnings and the TPMS will monitor the actual tire pressure in The “Tire Pressure Monitoring Telltale Light” will the tire. illuminate in the instrument cluster, a LOW TIRE message will be displayed for a minimum of five Base System seconds and a chime will sound when tire pressure is low...
Page 349 STARTING AND OPERATING 347 Check TPMS Warning 5. Using wheels/tires not equipped with TPM sensors. The “Tire Pressure Monitoring Telltale Light” will flash NOTE: on and off for 75 seconds and then remain on solid when 1. The compact spare tire (if equipped) does not have a a system fault is detected.
Page 350: Premium System - If Equipped
348 STARTING AND OPERATING 4. For each subsequent ignition key cycle, a chime will NOTE: It is particularly important for you to check the sound and the “Tire Pressure Monitoring Telltale Light” tire pressure in all of the tires on your vehicle monthly will flash on and off for 75 seconds and then remain on and to maintain the proper pressure.
Page 351 STARTING AND OPERATING 349 Tire Pressure Monitoring Low Pressure Warnings The “Tire Pressure Monitoring Telltale Light” will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the Electronic Vehicle Information Center (EVIC) will display a graphic showing the pressure values of each tire with the low tire pressure values flashing.
Page 352 350 STARTING AND OPERATING Should this occur, you should stop as soon as possible, display dashes (- -) in place of the pressure value to and inflate all tires with low pressure (those flashing in indicate which sensor is not being received. the EVIC graphic) to the vehicle’s recommended cold placard pressure value.
Page 353 STARTING AND OPERATING 351 If the ignition key is cycled, this sequence will repeat, The EVIC will also display a CHECK TPM SYSTEM providing the system fault still exists. If the system fault message for a minimum of five seconds when a system no longer exists, the “Tire Pressure Monitoring Telltale fault related to an incorrect sensor location fault is Light”...
Page 354: General Information
352 STARTING AND OPERATING Monitoring Telltale Light” will remain ON, a chime will 5. Once you repair or replace the original road tire, and sound, and the EVIC will still display a flashing pressure reinstall it on the vehicle in place of the compact spare, value in the graphic display.
Page 355: Fuel Requirements
STARTING AND OPERATING 353 The tire pressure sensors are covered under one of the as hard starting, stalling, and hesitations. If you experi- following licenses: ence these symptoms, try another brand of gasoline before considering service for the vehicle. United States ....KR5S18002015B Over 40 auto manufacturers worldwide have issued and Canada.
Page 356: Gasoline/Oxygenate Blends
354 STARTING AND OPERATING The manufacturer supports the use of reformulated gaso- Problems that result from using gasoline containing line. Properly blended reformulated gasoline will pro- Methanol or gasoline containing more than 10% Ethanol vide excellent performance and durability of engine and are not the responsibility of the manufacturer and may fuel system components.
Page 357: Mmt In Gasoline
STARTING AND OPERATING 355 To fix a Non-FFV vehicle inadvertently fueled once with therefore, you should ask your gasoline retailer whether E-85 perform the following: the gasoline contains MMT. It is even more important to look for gasoline without MMT in Canada, because MMT •...
Page 358: Fuel System Cautions
356 STARTING AND OPERATING Fuel System Cautions CAUTION! (Continued) • The use of fuel additives, which are now being CAUTION! sold as octane enhancers, is not recommended. Follow these guidelines to maintain your vehicle’s Most of these products contain high concentra- performance: tions of methanol.
Page 359: Carbon Monoxide Warnings
STARTING AND OPERATING 357 Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper WARNING! maintenance. Have the exhaust system inspected Carbon monoxide (CO) in exhaust gases is deadly. every time the vehicle is raised. Have any abnor- Follow the precautions below to prevent carbon mal conditions repaired promptly.
Page 360: Ethanol Fuel (E-85)
358 STARTING AND OPERATING the other sections of this manual for information on CAUTION! features that are common between Flexible Fuel and gasoline-only powered vehicles. Only vehicles with the E-85 fuel filler door label can operate on E-85. Ethanol Fuel (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline.
Page 361: Fuel Requirements
Observing these precautions will avoid possible hard in MOPAR engine oils, and in equivalent oils meeting starting and/or significant deterioration in driveability Chrysler Specification MS-6395. The manufacturer re- during warm up. quires engine oils that are API Certified and meet the...
Page 362: Starting
Because E-85 fuel contains less energy per gallon/liter tensive fleet testing, to provide additional protection to than gasoline, you will experience an increase in fuel Chrysler Group LLC engines. Use MOPAR or an consumption. You can expect your miles per gallon equivalent oil meeting the specification MS-6395.
Page 363: Maintenance
STARTING AND OPERATING 361 Maintenance CAUTION! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect driveability. ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door, on the left rear quarter panel of the vehicle.
Page 364 362 STARTING AND OPERATING After removing the gas cap, place the gas cap tether cable CAUTION! over a hook on the inside of the fuel door. This keeps the • Damage to the fuel system or emission control gas cap suspended away from and protects the vehicle’s surface.
Page 365: Loose Filler Cap Message
STARTING AND OPERATING 363 Loose Filler Cap Message WARNING! (Continued) If the vehicles diagnostic system determines that the fuel • Never add fuel when the engine is running. This is filler cap in loose, improperly installed, or damaged, a in violation of most state and federal fire regula- “gASCAP”...
Page 366: Gross Vehicle Weight Rating (Gvwr)
364 STARTING AND OPERATING The label contains the following information: Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. • Name of manufacturer This includes driver, passengers, and cargo. The total • Month and year of manufacture load must be limited so that you do not exceed the GVWR.
Page 367: Overloading
STARTING AND OPERATING 365 Overloading Loading The load carrying components (axle, springs, tires, To load your vehicle properly, first figure out its empty wheels, etc.) of your vehicle will provide satisfactory weight, axle by axle and side by side. Store heavier items service as long as you do not exceed the GVWR and front down low and be sure you distribute their weight as and rear GAWR.
Page 368: Common Towing Definitions
366 STARTING AND OPERATING To maintain warranty coverage, follow the requirements Gross Trailer Weight (GTW) and recommendations in this manual concerning ve- The GTW is the weight of the trailer plus the weight of all hicles used for trailer towing. cargo, consumables and equipment (permanent or tem- porary) loaded in or on the trailer in its loaded and If you have any questions or concerns after reviewing...
Page 369 STARTING AND OPERATING 367 Gross Axle Weight Rating (GAWR) Trailer Tongue Weight (TW) The GAWR is the maximum capacity of the front and rear The tongue weight is the downward force exerted on the axles. Distribute the load over the front and rear axles hitch ball by the trailer.
Page 370: Trailer Hitch Classification
368 STARTING AND OPERATING Trailer Hitch Classification Trailer Hitch Classification Definitions The following chart provides the industry standard for Class Max. Trailer Hitch Industry the maximum trailer weight a given trailer hitch class can Standards tow and should be used to assist you in selecting the Class I - Light Duty 2,000 lbs (907 kg) correct trailer hitch for your intended towing condition.
Page 371: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING 369 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Maximum Trailer Weight Ratings Max. GTW Max. Trailer Tongue Wt. Engine/Transmission Max. Frontal Area (Gross Trailer Wt.) (See Note 1) 2.4L/Auto See Note 2...
Page 372: Trailer And Tongue Weight
370 STARTING AND OPERATING CAUTION! Towing a trailer with a larger than recommended frontal area could cause the engine to overheat or cause severe engine damage under extreme condi- tions. Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer.
Page 373: Towing Requirements
STARTING AND OPERATING 371 NOTE: Remember that everything put into or on the Towing Requirements trailer adds to the load on your vehicle. Also, additional To promote proper break-in of your new vehicle drive- factory-installed options, or authorized dealer-installed train components the following guidelines are recom- options, must be considered as part of the total load on mended: your vehicle.
Page 374 372 STARTING AND OPERATING WARNING! WARNING! (Continued) • Safety chains must always be used between your Improper towing can lead to a collision. Follow these vehicle and trailer. Always connect the chains to guidelines to make your trailer towing as safe as the frame or hook retainers of the vehicle hitch.
Page 375 STARTING AND OPERATING 373 • Check for signs of tire wear or visible tire damage WARNING! (Continued) before towing a trailer. Refer to “Tires – General 3. GAWR Information” in “Starting and Operating” for informa- 4. Trailer tongue weight rating for the trailer hitch tion on tread wear indicators and for proper inspection utilized (This requirement may limit the ability to procedure.
Page 376 374 STARTING AND OPERATING • An electronically actuated trailer brake controller is WARNING! required when towing a trailer with electronically • Do not connect trailer brakes to your vehicle’s actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic hydraulic brake lines.
Page 377: Towing Tips
STARTING AND OPERATING 375 Towing Tips If you REGULARLY TOW a trailer for more than 45 min- Before setting out on a trip, practice turning, stopping, utes of continuous operation, then change the automatic and backing the trailer in an area located away from transmission fluid and filter according to the interval heavy traffic.
Page 378: Recreational Towing (Behind Motorhome, Etc.)
376 STARTING AND OPERATING • Use speed control in flat terrain and with light loads to RECREATIONAL TOWING maximize fuel efficiency. (BEHIND MOTORHOME, ETC.) Cooling System Towing This Vehicle Behind Another Vehicle To reduce potential for engine and transmission over- Recreational towing is not allowed.
Page 379: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flashers ....378 Road Tire Installation ....388 If Your Engine Overheats .
Page 380: Hazard Warning Flashers
378 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel, below the radio. potential for overheating by taking the appropriate ac- tion.
Page 381: Engine Oil Overheating - 2.4L Engine Only (If Equipped)
WHAT TO DO IN EMERGENCIES 379 CAUTION! WARNING! Driving with a hot cooling system could damage You or others can be badly burned by hot engine your vehicle. If the pointer rises to the H (red) mark, coolant (antifreeze) or steam from your radiator. If the instrument cluster will sound a chime.
Page 382: Jacking And Tire Changing
380 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! (Continued) • The jack is designed to be used as a tool for WARNING! changing tires only. The jack should not be used to • Do not attempt to change a tire on the side of the lift the vehicle for service purposes.
Page 383: Preparations For Jacking
WHAT TO DO IN EMERGENCIES 381 WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 2.
Page 384: Jacking Instructions
382 WHAT TO DO IN EMERGENCIES 6. Block both the front and rear of the WARNING! (Continued) wheel diagonally opposite the jacking • Always park on a firm, level surface as far from position. For example, if changing the the edge of the roadway as possible before raising right front tire, block the left rear the vehicle.
Page 385 WHAT TO DO IN EMERGENCIES 383 WARNING! (Continued) CAUTION! • Only use the jack in the positions indicated and Do not attempt to raise the vehicle by jacking on for lifting this vehicle during a tire change. locations other than those indicated in the Jacking •...
Page 386 384 WHAT TO DO IN EMERGENCIES NOTE: The jack handle attaches to the side of the jack 2. Loosen, but do not remove, the wheel nuts by turning with two attachment points. When the jack is partially them to the left one turn while the wheel is still on the expanded, the tension between the two attachment ground.
Page 387 WHAT TO DO IN EMERGENCIES 385 Rear Jacking Location Front Jacking Location 4. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed.
Page 388 386 WHAT TO DO IN EMERGENCIES WARNING! CAUTION! Raising the vehicle higher than necessary can make Be sure to mount the spare tire with the valve stem the vehicle less stable. It could slip off the jack and facing outward. The vehicle could be damaged if the hurt someone near it.
Page 389 WHAT TO DO IN EMERGENCIES 387 9. Remove the wheel blocks and lower the jack until it is WARNING! free. Reassemble the lug wrench to the jack assembly and • To avoid the risk of forcing the vehicle off the jack, stow it in the spare tire area.
Page 390: Road Tire Installation
388 WHAT TO DO IN EMERGENCIES Road Tire Installation Vehicles Equipped With Wheel Covers 1. Mount the road tire on the axle. 2. To ease the installation process for steel wheels with wheel covers, install two lug nuts on the mounting studs which are on each side of the valve stem.
Page 391 WHAT TO DO IN EMERGENCIES 389 3. Align the valve notch in the wheel cover with the 6. Finish tightening the lug nuts. Push down on the valve stem on the wheel. Install the cover by hand, wrench while at the end of the handle for increased snapping the cover over the two lug nuts.
Page 392: Jump-Starting
390 WHAT TO DO IN EMERGENCIES 5. After 25 miles (40 km) check the lug nut torque with a WARNING! torque wrench to ensure that all lug nuts are properly seated against the wheel. To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle JUMP-STARTING has been lowered.
Page 393: Preparations For Jump-Start
WHAT TO DO IN EMERGENCIES 391 CAUTION! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur. WARNING! Do not attempt jump-starting if the battery is frozen.
Page 394 392 WHAT TO DO IN EMERGENCIES 3. Remove the protective cover over the remote positive WARNING! (+) battery post. To remove the cover, press the locking • Take care to avoid the radiator cooling fan when- tab and pull upward on the cover. ever the hood is raised.
Page 395: Jump-Starting Procedure
WHAT TO DO IN EMERGENCIES 393 1. Connect the positive (+) end of the jumper cable to the WARNING! remote positive (+) post of the discharged vehicle. Do not allow vehicles to touch each other as this 2. Connect the opposite end of the positive (+) jumper could establish a ground connection and personal cable to the positive (+) post of the booster battery.
Page 396 394 WHAT TO DO IN EMERGENCIES 5. Start the engine in the vehicle that has the booster 10. Reinstall the protective cover over the remote posi- battery, let the engine idle a few minutes, and then start tive (+) battery post of the discharged vehicle. the engine in the vehicle with the discharged battery.
Page 397: Freeing A Stuck Vehicle
WHAT TO DO IN EMERGENCIES 395 FREEING A STUCK VEHICLE NOTE: If your vehicle is equipped with Electronic If your vehicle becomes stuck in mud, sand, or snow, it Stability Control (ESC), turn the system to Partial OFF can often be moved by a rocking motion. Turn your before attempting to “rock”...
Page 398: Shift Lever Override
396 WHAT TO DO IN EMERGENCIES 3. Turn the ignition to the ON/RUN position without WARNING! starting the engine. Fast spinning tires can be dangerous. Forces gener- 4. Press and maintain firm pressure on the brake pedal. ated by excessive wheel speeds may cause damage, or 5.
Page 399: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES 397 TOWING A DISABLED VEHICLE Towing Condition Wheels OFF the Ground ALL MODELS Flat Tow NONE If transmission is operable: • Trans in NEUTRAL • 25 mph (40 km/h)max speed Rear Wheel Lift Or Dolly Tow •...
Page 400 398 WHAT TO DO IN EMERGENCIES If flatbed equipment is not available, and the transmis- CAUTION! sion is operable, the vehicle may be flat towed (with all • Do not use sling type equipment when towing. four wheels on the ground) under the following condi- tions: Damage to the fascia will occur.
Page 401: Without The Ignition Key
WHAT TO DO IN EMERGENCIES 399 the ground) is not allowed, as transmission damage will CAUTION! occur. If rear towing is the only alternative, the front wheels must be placed on a towing dolly. Proper towing Towing faster than 25 mph (40 km/h) or farther than equipment is necessary to prevent damage to the vehicle.
Page 403 MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment — 2.4L ... . . 403 Maintenance Procedures ....408 Engine Compartment —...
Page 404 402 MAINTAINING YOUR VEHICLE Adding Washer Fluid ....419 Replacement Bulbs ....446 Exhaust System .
Page 405: Engine Compartment - 2.4L
MAINTAINING YOUR VEHICLE 403 ENGINE COMPARTMENT — 2.4L 1 — Engine Coolant Reservoir 7 — Air Cleaner Filter 2 — Power Steering Fluid Reservoir 8 — Engine Oil Fill 3 — Automatic Transmission Dipstick 9 — Coolant Pressure Cap 4 — Brake Fluid Reservoir 10 —...
Page 406: Engine Compartment - 3.6L
404 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.6L 1 — Engine Coolant Reservoir 5 — Air Cleaner Filter 2 — Power Steering Fluid Reservoir 6 — Engine Oil Dipstick 3 — Brake Fluid Reservoir 7 — Engine Oil Fill 4 — Totally Integrated Power Module (Fuses) 8 —...
Page 407: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 405 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic further damage to the emission control system.
Page 408: Emissions Inspection And Maintenance Programs
406 MAINTAINING YOUR VEHICLE persists, the message will appear the next time the Normally, the OBD II system will be ready. The OBD II vehicle is started. This might indicate a damaged cap. If system may not be ready if your vehicle was recently the problem is detected twice in a row, the system will serviced, recently had a dead battery or a battery replace- turn on the “Malfunction Indicator Light (MIL).”...
Page 409: Replacement Parts
MAINTAINING YOUR VEHICLE 407 4. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced a.
Page 410: Maintenance Procedures
Immediately have potential malfunctions examined by an authorized Chrysler Group LLC dealership or qualified repair center. (Continued)
Page 411: Engine Oil
MAINTAINING YOUR VEHICLE 409 fully warmed engine is shut off. Do not check oil level CAUTION! (Continued) before starting the engine after it has sat overnight. • Your vehicle has been built with improved fluids Checking engine oil level when the engine is cold will that protect the performance and durability of give you an incorrect reading.
Page 412 API Certified and meet the will cause oil aeration, which can lead to loss of oil requirements of Chrysler Material Standard MS-6395. pressure and an increase in oil temperature. This could damage your engine. Also, be sure the oil fill American Petroleum Institute (API) Engine Oil cap is replaced and tightened after adding oil.
Page 413 MAINTAINING YOUR VEHICLE 411 Lubricants which do not have both the engine oil certi- CAUTION! fication mark and the correct SAE viscosity grade num- ber should not be used. Do not use chemical flushes in your engine oil as the chemicals can damage your engine.
Page 414: Engine Oil Filter
412 MAINTAINING YOUR VEHICLE Lubricants which do not have both, the engine oil certi- station, or governmental agency for advice on how and fication mark and the correct SAE viscosity grade num- where used oil and oil filters can be safely discarded in ber should not be used.
Page 415: Engine Air Cleaner Filter
MAINTAINING YOUR VEHICLE 413 Engine Air Cleaner Filter Engine Air Cleaner Filter Selection The quality of replacement engine air cleaner filters WARNING! varies considerably. Only high quality filters should be used to assure most efficient service. MOPAR engine air The air induction system (air cleaner, hoses, etc.) can cleaner filters are high quality and are recommended.
Page 416 414 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can • It is essential when replacing the cables on the burn or even blind you. Do not allow battery fluid battery that the positive cable is attached to the to contact your eyes, skin, or clothing.
Page 417: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 415 Air Conditioner Maintenance WARNING! For best possible performance, your air conditioner • Use only refrigerants and compressor lubricants should be checked and serviced by an authorized dealer at the start of each warm season. This service should approved by the manufacturer for your air condi- include cleaning of the condenser fins and a performance tioning system.
Page 418: A/C Air Filter - If Equipped
416 MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling The A/C Air Filter is located in the fresh air inlet behind R-134a air conditioning refrigerant is a hydrofluoro- the glove box. Perform the following procedure to re- carbon (HFC) that is endorsed by the Environmental place the filter: Protection Agency and is an ozone-saving product.
Page 419: Body Lubrication
MAINTAINING YOUR VEHICLE 417 CAUTION! The A/C Air Filter is identified with an arrow to indicate airflow direction through the filter. Failure to install the filter properly will result in the need to replace it more often. 8. Reinstall the glove box door dampener and glove box. Body Lubrication Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate,...
Page 420: Windshield Wiper Blades
418 MAINTAINING YOUR VEHICLE hood latching components to ensure proper function. Operation of the wipers on dry glass for long periods When performing other underhood services, the hood may cause deterioration of the wiper blades. Always use latch, release mechanism and safety catch should be washer fluid when using the wipers to remove salt or dirt cleaned and lubricated.
Page 421: Adding Washer Fluid
MAINTAINING YOUR VEHICLE 419 Adding Washer Fluid Exhaust System The fluid reservoir for the windshield washers is located The best protection against carbon monoxide entry into in the engine compartment. Be sure to check the fluid the vehicle body is a properly maintained engine exhaust level in the reservoir at regular intervals.
Page 422 420 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Exhaust gases can injure or kill. They contain • The catalytic converter requires the use of un- carbon monoxide (CO), which is colorless and leaded fuel only. Leaded gasoline will destroy the odorless. Breathing it can make you unconscious effectiveness of the catalyst as an emissions con- and can eventually poison you.
Page 423 MAINTAINING YOUR VEHICLE 421 Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter dam- verter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage.
Page 424: Cooling System
422 MAINTAINING YOUR VEHICLE Cooling System rusty in appearance, the system should be drained, flushed, and refilled with fresh engine coolant (anti- WARNING! freeze). Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently •...
Page 425 MAINTAINING YOUR VEHICLE 423 Selection Of Coolant CAUTION! (Continued) Use only the manufacturer’s recommended coolant. Re- • Do not use water alone or alcohol-based engine fer to “Fluids, Lubricants, and Genuine Parts” in “Main- coolant (antifreeze) products. Do not use addi- taining Your Vehicle”...
Page 426 424 MAINTAINING YOUR VEHICLE replacement. To prevent reducing this extended mainte- (antifreeze) solution. The use of lower quality water nance period, it is important that you use the same will reduce the amount of corrosion protection in the engine coolant (antifreeze) throughout the life of your engine cooling system.
Page 427 MAINTAINING YOUR VEHICLE 425 rules for your community. To prevent ingestion by ani- WARNING! mals or children, do not store ethylene glycol based • The warning words “DO NOT OPEN HOT” on engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground.
Page 428 426 MAINTAINING YOUR VEHICLE The radiator normally remains completely full, so there is If an examination of your engine compartment shows no no need to remove the radiator cap unless checking for evidence of radiator or hose leaks, the vehicle may be engine coolant (antifreeze) freeze point or replacing cool- safely driven.
Page 429: Brake System
MAINTAINING YOUR VEHICLE 427 • Make sure that the radiator and coolant recovery WARNING! bottle overflow hoses are not kinked or obstructed. Riding the brakes can lead to brake failure and • Keep the front of the radiator clean. If your vehicle is possibly a collision.
Page 430 428 MAINTAINING YOUR VEHICLE Clean the top of the master cylinder area before removing WARNING! the cap. If necessary, add fluid to bring the fluid level up • Use only manufacturer’s recommended brake to the requirements described on the brake fluid reser- voir.
Page 431: Automatic Transmission
MAINTAINING YOUR VEHICLE 429 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or • Do not allow petroleum based fluid to contami- moisture, use only new brake fluid or fluid that nate the brake fluid. Brake seal components could has been in a tightly closed container.
Page 432 430 MAINTAINING YOUR VEHICLE Parts” in “Maintaining Your Vehicle” for further informa- Special Additives tion. It is important that the transmission fluid be main- Automatic Transmission Fluid (ATF) is an engineered tained at the prescribed level using the recommended product and its performance may be impaired by supple- fluid.
Page 433 MAINTAINING YOUR VEHICLE 431 Fluid Level Check – 2.4L Engine driven at least 15 miles (24 km). Hot fluid cannot be held Use the following procedure to check the automatic comfortably between the fingertips. Cold fluid is at a transmission fluid level properly: temperature below 80°...
Page 434: Appearance Care And Protection From Corrosion
432 MAINTAINING YOUR VEHICLE Fluid Level Check – 3.6L Engine CAUTION! The automatic transmission has no dipstick and is dealer • Using a transmission fluid other than the manu- serviced only. facturer’s recommended fluid may cause deterio- Transmission Fluid And Filter Changes ration in transmission shift quality and/or torque Refer to the “Maintenance Schedule”...
Page 435 MAINTAINING YOUR VEHICLE 433 hot or cold weather and other extreme conditions will Washing have an adverse effect on paint, metal trim, and under- • Wash your vehicle regularly. Always wash your ve- body protection. hicle in the shade using MOPAR Car Wash or equiva- The following maintenance recommendations will enable lent, or a mild car wash soap, and rinse the panels you to obtain maximum benefit from the corrosion...
Page 436 434 MAINTAINING YOUR VEHICLE • If you detect any stone chips or scratches in the paint, CAUTION! touch them up immediately. The cost of such repairs is • Do not use abrasive or strong cleaning materials considered the responsibility of the owner. such as steel wool or scouring powder, which will •...
Page 437 MAINTAINING YOUR VEHICLE 435 Wheel And Wheel Trim Care To minimize the possibility of scratching the lenses and All wheels and wheel trim, especially aluminum and reducing light output, avoid wiping with a dry cloth. To chrome-plated wheels, should be cleaned regularly with remove road dirt, wash with a mild soap solution fol- a mild soap and water to prevent corrosion.
Page 438 436 MAINTAINING YOUR VEHICLE • For grease stains, apply MOPAR Multi-Purpose if absolutely necessary. Do not use harsh cleaners or Cleaner or equivalent to a clean, damp cloth and Armor All . Use MOPAR Total Clean or equivalent to remove the stain. Use a fresh, damp towel to remove clean vinyl upholstery.
Page 439 MAINTAINING YOUR VEHICLE 437 Cleaning Plastic Instrument Cluster Lenses WARNING! The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care Do not use volatile solvents for cleaning purposes. must be taken to avoid scratching the plastic. Many are potentially flammable, and if used in closed areas they may cause respiratory harm.
Page 440: Cleaning Center Console Cupholders
438 MAINTAINING YOUR VEHICLE Replace the belts if they appear frayed or worn or if the Convertible Top Care buckles do not work properly. CAUTION! Cleaning Center Console Cupholders Failure to follow these cautions may cause interior Removal water damage, stains or mildew on the top material: Grab the rubber portion of the cupholder and lift upward.
Page 441 MAINTAINING YOUR VEHICLE 439 Immediate removal of any contaminant is recommended. General Cleaning Regular washing of the top will enhance its life and Careful vacuuming of the top before washing is helpful appearance, and make successive cleanings easier. Do not in removing dust and other foreign particles.
Page 442: Weather Strip Care - Soft And Hard Top
440 MAINTAINING YOUR VEHICLE the top fabric and to prevent streaking on painted and Protection chrome surfaces. Allow the top to dry before lowering. For appearance purposes, you may wish to protect your Vacuuming the top with a wet/dry shop vacuum will cloth top periodically.
Page 443: Fuses
MAINTAINING YOUR VEHICLE 441 FUSES Totally Integrated Power Module The Totally Integrated Power Module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A label that identifies each component may be printed on the inside of the cover.
Page 444 442 MAINTAINING YOUR VEHICLE Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse Center High Battery Feed – Power 10 Amp Mounted Stop Light 40 Amp Seats – If Equipped/ — (CHMSL)/Brake Green PZEV Air Pump – If Switch Equipped 10 Amp...
Page 445 MAINTAINING YOUR VEHICLE 443 Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse 40 Amp Ignition Run – Cli- — Radiator Fan Relay Green 10 Amp mate Controls/Hot — Cupholder – If Cigar Lighter/ 15 Amp Equipped —...
Page 446 444 MAINTAINING YOUR VEHICLE Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse Ignition Run – Occu- 30 Amp Auto Shutdown — pant Classification Pink (ASD) Relay 1 10 Amp — Module (OCM)/ Switch Bank/ Occupant Restraint Diagnostic Link 10 Amp Controller (ORC)
Page 447 MAINTAINING YOUR VEHICLE 445 Cartridge Mini CAUTION! Cavity Description Fuse Fuse • When installing the Totally Integrated Power Anti-Lock Brakes Module cover, it is important to ensure the cover is (ABS) Module – If properly positioned and fully latched. Failure to 40 Amp Equipped/Electronic —...
Page 448: Vehicle Storage
446 MAINTAINING YOUR VEHICLE VEHICLE STORAGE REPLACEMENT BULBS If you will not be using your vehicle for more than All the inside bulbs are brass or glass wedge base. 21 days, you may want to take steps to preserve your Aluminum base bulbs are not approved and should not battery.
Page 449: Bulb Replacement
MAINTAINING YOUR VEHICLE 447 NOTE: It may be necessary to remove the air cleaner LIGHT BULBS – Exterior Bulb No. filter housing and position the totally integrated power Bi-Halogen Headlamp ....HIR2 module aside prior to replacing the low beam headlamp (Serviced at Authorized Dealer) on the driver’s side of the vehicle.
Page 450 448 MAINTAINING YOUR VEHICLE 3. Rotate bulb and connector one-quarter turn and pull 4. Pull the bulb out of the socket and replace the bulb. outward from assembly. 5. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. CAUTION! 6.
Page 451: Front Turn Signal
MAINTAINING YOUR VEHICLE 449 Front Turn Signal 1. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the fog lamp hous- 1. Raise and prop open the hood. ing. 2. Rotate the bulb’s electrical connector one-quarter turn 2.
Page 452: Backup Lamps
450 MAINTAINING YOUR VEHICLE Backup Lamps NOTE: Placing a small flat head screwdriver or similar tool between the lamp outboard ball stud and plastic 1. Open the trunk and gently pull back the trunk liner grommet from inside the trunk can assist in lamp re- behind the tail lamp.
Page 453: License Plate Lamp
MAINTAINING YOUR VEHICLE 451 License Plate Lamp 2. Pull bulb from socket, replace, and reinstall the lamp assembly into place ensuring the locking tab is secure. 1. Using a small screwdriver, press inward the locking tab on the side of the lamp assembly and pull down on the lamp assembly for removal.
Page 454: Fluids, Lubricants, And Genuine Parts
Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Engine Oil – 2.4L Engine Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for correct SAE grade. Use API Certified SAE 5W-30 Engine Oil, meeting Chrysler Material Stan- Engine Oil –...
Page 455: Chassis
MAINTAINING YOUR VEHICLE 453 Chassis Component Fluid, Lubricant, or Genuine Part MOPAR ATF+4 Automatic Transmission Fluid or equivalent licensed Automatic Transmission ATF+4 product. MOPAR DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not Brake Master Cylinder available, then DOT 4 is acceptable.
Page 457 MAINTENANCE SCHEDULES CONTENTS Maintenance Schedule ....456 Required Maintenance Intervals ..458...
Page 458 456 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE Based on engine operation conditions the oil change The Scheduled Maintenance services listed in this indicator message will illuminate, this means that service manual must be done at the times or mileages specified is required for your vehicle. Have your vehicle serviced to protect your vehicle warranty and ensure the best as soon as possible, within the next 500 miles (805 km).
Page 459 MAINTENANCE SCHEDULES 457 Your authorized dealer will reset the oil change indicator At Each Stop For Fuel message after completing the scheduled oil change. If a • Check the engine oil level about five minutes after a scheduled oil change is performed by someone other fully warmed engine is shut off.
Page 460 458 MAINTENANCE SCHEDULES Once A Month At Each Oil Change • Check tire pressure and look for unusual wear or • Change the engine oil filter. damage. • Inspect the brake hoses and lines. • Inspect the battery and clean and tighten the terminals CAUTION! as required.
Page 461 MAINTENANCE SCHEDULES 459 8,000 Miles (13,000 km) or 16,000 Miles (26,000 km) or 12 Months Maintenance Service 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 462: Service Schedule
460 MAINTENANCE SCHEDULES 24,000 Miles (39,000 km) or 32,000 Miles (52,000 km) or 24 Months Maintenance Service 18 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 463 MAINTENANCE SCHEDULES 461 40,000 Miles (65,000 km) or 48,000 Miles (78,000 km) or 36 Months Maintenance Service 30 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 464 462 MAINTENANCE SCHEDULES 56,000 Miles (91,000 km) or 64,000 Miles (104,000 km) or 48 Months Maintenance Service 42 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 465 MAINTENANCE SCHEDULES 463 72,000 Miles (117,000 km) or 80,000 Miles (130,000 km) or 60 Months Maintenance Service 54 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 466 464 MAINTENANCE SCHEDULES 88,000 Miles (143,000 km) or 96,000 Miles (156,000 km) or 72 Months Maintenance Service 66 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 467 MAINTENANCE SCHEDULES 465 104,000 Miles (169,000 km) or 112,000 Miles (182,000 km) or 84 Months Maintenance Service 78 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 468 466 MAINTENANCE SCHEDULES 120,000 Miles (195,000 km) or 128,000 Miles (208,000 km) or 96 Months Maintenance Service 90 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 469 MAINTENANCE SCHEDULES 467 136,000 Miles (221,000 km) or 144,000 Miles (234,000 km) or 108 Months Maintenance Service 102 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 470 468 MAINTENANCE SCHEDULES 152,000 Miles (247,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 152,000 miles (247 000 km). Odometer Reading Date Repair Order #...
Page 471 MAINTENANCE SCHEDULES 469 † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment.
Page 473: If You Need Consumer Assistance
If You Need Assistance ....473 Reporting Safety Defects ....476 Chrysler Group LLC Customer Center ..474 In The 50 United States And Washington, D.C.
Page 474 472 IF YOU NEED CONSUMER ASSISTANCE Department Of Transportation Uniform Tire Traction Grades ..... 479 Quality Grades ......479 Temperature Grades .
Page 475: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 473 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
Page 476: Chrysler Group Llc Customer Center
474 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 solved with this process. Auburn Hills, MI 48321–8004 Phone: (800) 247–9753...
Page 477: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
IF YOU NEED CONSUMER ASSISTANCE 475 Customer Assistance For The Hearing Or Speech the manufacturer’s service contracts. If you purchased a Impaired (TDD/TTY) manufacturer’s service contract, you will receive Plan To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date.
Page 478: Warranty Information
See the Warranty Information Booklet, located on the has also made a major investment in facilities, tools, and DVD, for the terms and provisions of Chrysler Group training to assure that you are absolutely delighted with LLC warranties applicable to this vehicle and market.
Page 479: In Canada
IF YOU NEED CONSUMER ASSISTANCE 477 If NHTSA receives similar complaints, it may open an In Canada investigation, and if it finds that a safety defect exists in If you believe that your vehicle has a safety defect, you a group of vehicles, it may order a recall and remedy should contact the Customer Service Department imme- campaign.
Page 480 Chrysler Group LLC ve- maintaining, servicing, and repairing Chrysler Group hicles. Included are starting, operating, emergency LLC vehicles. A complete working knowledge of the...
Page 481 IF YOU NEED CONSUMER ASSISTANCE 479 DEPARTMENT OF TRANSPORTATION UNIFORM significantly from the norm due to variations in driving TIRE QUALITY GRADES habits, service practices, and differences in road charac- The following tire grading categories were established by teristics and climate. the National Highway Traffic Safety Administration.
Page 482 480 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat, when tested under a tire that is properly inflated and not overloaded.
Page 483 INDEX...
Page 484 482 INDEX About Your Brakes ..... . . 310 Airbag Maintenance ..... . . 65 ABS (Anti-Lock Brake System) .
Page 485 INDEX 483 Automatic Door Locks ..... 32 B-Pillar Location ......328 Automatic Headlights .
Page 486 484 INDEX Calibration, Compass ..... 216 Child Restraint ....67,69,73,75 Capacities, Fluid .
Page 487 INDEX 485 Console, Floor ......183 Customer Assistance ..... 473 Contract, Service .
Page 488 486 INDEX Disposal Emergency Deck Lid Release ....38 Antifreeze (Engine Coolant) ... . . 425 Emergency Trunk Release .
Page 489 INDEX 487 Flooded, Starting ..... 295 Exhaust System ..... . . 80,419 Fuel Requirements .
Page 490 488 INDEX Fuel Requirements ....357,359 Fuel ....... . . 353 Maintenance .
Page 491 INDEX 489 Garage Door Opener (HomeLink®) ... 172 Hands-Free Phone (Uconnect™) ... . . 111 Gas Cap (Fuel Filler Cap) ... . 361,363,405 Hazard Gasoline, Clean Air .
Page 492 490 INDEX Heated Mirrors ......110 Information Center, Vehicle ....210 Heated Seats .
Page 493 INDEX 491 Key, Sentry (Immobilizer) ....14 Automatic Headlights ....158 Keyless Entry System .
Page 494 492 INDEX High Beam/Low Beam Select ... . 162 Warning (Instrument Cluster Description) . . . 194 Illuminated Entry ..... 20 Loading Vehicle .
Page 495 INDEX 493 Malfunction Indicator Light (Check Engine) . . 206,406 New Vehicle Break-In Period ....78 Manual, Service ......477 Map/Reading Lights .
Page 496 494 INDEX Filter Disposal ..... . . 412 Personal Settings ......218 Identification Logo .
Page 497 INDEX 495 Programming Transmitters Remote Control (Remote Keyless Entry) ....20 Security Alarm ..... . . 18 Starting System .
Page 498 496 INDEX Safety Checks Inside Vehicle ....80 Reminder ......195 Safety Checks Outside Vehicle .
Page 499 INDEX 497 Service Manuals ......477 Starting ......27,294 Setting the Clock .
Page 500 498 INDEX Tachometer ......198 Compact Spare ..... . 336 Taillights .
Page 501 INDEX 499 To Open Hood ......155 Transaxle Tongue Weight/Trailer Weight ....370 Automatic .
Page 502 500 INDEX Trip Odometer Reset Button ....202 Vehicle Identification Number (VIN) ... . 6 Trunk Lid (Deck Lid) .
Page 503 INDEX 501 Wheel and Wheel Trim Care ....435 Windshield Wiper Blades ....418 Wind Buffeting .
Page 504 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
Page 505 Chrysler Group LLC 11C27-126-AD Fourth Edition Printed in U.S.A.

This manual is also suitable for:

2011 200 200 convertible

Chrysler 200 CONVERTIBLE 2011 Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Quick Links

Chapters

Related Manuals for Chrysler 200 CONVERTIBLE 2011

Summary of Contents for Chrysler 200 CONVERTIBLE 2011