Docomo Prime SH-06A Instruction Manual page 573

List of AT command
[M]: AT commands that can be used with the FOMA SH06A Modem Port.
AT command
AT
―
[M]
AT%V Displays FOMA terminal
version. *2
[M]
AT&C<n> Sets operating condition for circuit
CD (DCD) signals sent to DTE.
[M]
AT&D<n> Sets the operation when the
circuit ER (DTR) signal received
from DTE changes from "ON" to
"OFF" during online data mode.
[M]
AT&E<n> Selects speed display
specifications when connecting.
[M]
AT&F<n> Resets the FOMA terminal's AT
command settings to their default
settings. If this command is
entered during communication,
the settings are reset after
disconnected.
[M]
AT&S<n> Controls when the signal of data
set ready (DR) is set to DTE.
[M]
AT&W<n> Stores the current settings in the
FOMA terminal's memory.
[M]
AT*DANTE Displays the reception status of
the FOMA terminal.
[M]
AT*DGANSM= Sets Accept/Reject call modes for
<n> incoming packet communications.
This setting is only valid for
incoming packet communications
after entering setup commands.
[M]
AT*DGAPL=<n> Sets host (APN) to accept
[,<cid>] transmissions for incoming packet
communications. APN settings
use <cid> parameter defined by
"+CGDCONT".
[M]
Overview
The modem function of the FOMA terminal
can be controlled by adding commands in the
list to the end of this command.
※ Returns OK if only AT is entered.
―
n=0: Circuit CD always ON
*1 n=1: Circuit CD signal changes according to
When "&C1" is set, the CD signal is turned
"ON" directly before the CONNECT signal is
sent when connection is completed. The CD
signal is turned "OFF" right before "NO
CARRIER" is sent when the circuit is
disconnected.
n=0: Ignores status (always considers signal
n=1: Sets online command mode when
*1
n=2: Disconnects line and activates offline
n=0: Wireless area transmission speed
*1
n=1: DTE serial transmission speed appears.
Can only be set as n=0 (can be omitted)
*2
n=0: Always ON (default setting)
*1 n=1: DR signal ON when line is connected
Can only be set as n=0 (can be omitted)
*2, 5
The result from this command is in the
following format.
*2
*DANTE:<m>
<m>
0:
1:
2:
3:
n=0: Sets Reject call and Accept call settings
n=1: Sets Reject call settings to [ON]
n=2: Sets Accept call settings to [ON]
*2
Adds or deletes from Accept calls list with <n>
parameter. If <cid> parameter is abbreviated,
adds (<n>=0) or deletes (<n>=1) all of <cid>
to or from list. Adds (deletes) <cid> not
defined with "+CGDCONT" to (from) list with
*2
this command.
n=0: Adds to list (Adds APN defined by <cid>
n=1: Deletes from list (Deletes APN defined
Parameter/Explanation
line connection status (default setting)
ON)
signal changes from ON to OFF
mode when signal changes from ON to
OFF (default setting)
appears
(Default setting)
Status where outside the service area
appears on the FOMA terminal
Status where zero or one antenna
appears on the FOMA terminal
Status where two antennas appears on
the FOMA terminal
Status where three antennas appears on
the FOMA terminal
to [OFF] (Default setting)
to Accept calls list)
by <cid> from Accept calls list)
24
Execution
example
ATo
OK
AT%Vo
Ver1.00
OK
AT&C1o
OK
AT&D1o
OK
AT&E0o
OK
AT&Fo
OK
AT&S0o
OK
AT&Wo
OK
AT*DANTEo
*DANTE:3
OK
AT*DGANSM=0o
OK
AT*DGANSM?o
*DGANSM:0
OK
AT*DGAPL=0,1o
OK
AT*DGAPL?o
*DGAPL:1
OK