Download  Print this page

Troubleshooting - Brother Quattro 2 6700D Operation Manual

Embroidery and sewing machine.
Hide thumbs

Advertisement

Table of Contents

TROUBLESHOOTING

If you have a minor problem with your sewing machine, check the following solutions. If the solutions
suggested do not correct the problem, contact your authorized dealer. Press
for advice about minor sewing problems during sewing. Press
the original screen.
If you need additional help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips.
Visit us at " http://solutions.brother.com ".
If the problem persists, contact your dealer or the nearest authorized service center.
Problem
The thread is tangled
Upper threading is incorrect.
on the wrong side of
the fabric.
Using improper needle or thread for the
selected fabric.
The upper thread is
The bobbin thread is incorrectly installed.
too tight.
Cannot thread the
Needle is not in the correct position.
needle
Needle is installed incorrectly.
Needle is turned, bent or the point is dull.
Cannot lower the
Presser foot was raised using the "Presser Foot
presser foot with the
Lifter" button.
presser foot lever
Thread tension is
Upper threading is incorrect.
incorrect
Bobbin is set incorrectly.
Using improper needle or thread for the
selected fabric.
Presser foot holder is not attached correctly.
Thread tension is set incorrectly.
Bobbin thread is incorrectly wound.
Needle is turned, bent or the point is dull.
Upper thread breaks
Machine is not threaded correctly (used the
wrong spool cap, spool cap is loose, the thread
did not catch the needle bar threader, etc.)
Needle is turned, bent or the point is dull.
There are scratches on the race.
Upper thread tension is too strong.
Using improper needle or thread for the
selected fabric.
Thread is twisted.
There are scratches near the hole of the needle
plate.
There are scratches near the hole in the presser
foot.
Needle is installed incorrectly.
Thread is knotted or tangled.
A bobbin designed specifically for this machine
is not used.
Cause
Check the steps for threading the machine
and rethread the machine.
Check the "Fabric/Thread/Needle
Combinations" chart.
Correctly install the bobbin thread.
Press the "Needle Position" button to raise the
needle.
Reinstall the needle correctly.
Replace the needle.
Press the "Presser Foot Lifter" button to lower
the presser foot.
Check the steps for threading the machine
and rethread the machine.
Reset the bobbin. (If needle plate was
removed, reinstall needle plate and tighten
screws prior to installing bobbin case.)
Check the "Fabric/Thread/Needle
Combination" chart.
Reattach the presser foot holder correctly.
Adjust the thread tension.
Use a correctly wound bobbin.
Replace the needle.
Rethread the machine correctly.
Replace the needle.
Replace the race, or consult your authorized
dealer.
Adjust the thread tension.
Check the "Fabric/Thread/Needle
Combinations" chart.
Use scissors, etc., to cut the twisted thread
and remove it from the race, etc.
Replace the needle plate, or consult your
authorized dealer.
Replace the presser foot, or consult your
authorized dealer.
Reinstall the needle correctly.
Rethread upper and lower thread.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
TROUBLESHOOTING
at any time to return to
Solution
Page
57
69
54
15
67
67
15
57
54
69
66
79, 233
48
67
57
67
338
79, 233
69
97
9
65
67
54, 57
54
343

Advertisement

Table of Contents

Troubleshooting

   Related Manuals for Brother Quattro 2 6700D

This manual is also suitable for:

Nv6700d

Comments to this Manuals

Symbols: 0
Latest comments:
  • handyman0031 Jan 03, 2015 10:26:
    please provide a part number for the zigzag embroidery plate,it's included with the 6700 D, however no part number is referenced anywhere in the stupid manual, and there is no item anywhere to replace it? After spending 10 K you think you could put a part number in a book so I can reorder one? my machine jammed and this one has a huge bur on it that cannot be worked out :-(