Mitsubishi Electric M80V Series Manual page 774

(Power regeneration amount) ......................... 678
(Program number at machining start) ............. 677
(Serial number) ............................................... 675
(Spindle 1 load value) ..................................... 682
(Spindle 1 maximum load) .............................. 678
(Spindle 2 load value) ..................................... 683
(Spindle 2 maximum load) .............................. 678
(Subprogram number at alarm)....................... 682
(Time of alarm occurrence) ............................. 681
(Time of power ON) ........................................ 681
(Tool length offset 1 to 5) ................................ 679
(Tool length offset) .......................................... 683
(Tool length wear amount 1 to 5) .................... 680
(Tool length wear amount) .............................. 683
(Tool life 1 to 5) ............................................... 680
(Tool life) ......................................................... 684
(Tool number 1 to 5) ....................................... 679
(Tool number) ................................................. 683
(Tool offset number 1 to 5).............................. 679
(Tool offset number)........................................ 683
(Tool radius offset 1 to 5) ................................ 679
(Tool radius offset) .......................................... 683
(Tool radius wear amount 1 to 5) .................... 680
(Tool radius wear amount) .............................. 684
(User arbitrary C1 at machining end) .............. 680
(User arbitrary L1 to L10 at machining end) ... 680
(User area C1 at alarm) .................................. 684
(User area L1 to L10 at alarm) ........................ 684
(Program number at alarm).............................. 681
Data protection key (DS)....................................... 520
Data protection key (memory card)....................... 520
Data protection key 1 ............................................ 357
Data protection key 2 ............................................ 358
Data protection key 3 ............................................ 358
Detailed screen No................................................ 529
Diagnosis data output:
Accumulated travel distance (motor) ............... 689
Automatic log clear time................................... 688
Battery exchange (drive) .................................. 687
Battery exchange ............................................. 687
Motor insulation degradation detection
request....................................................... 625
Motor insulation resistance (motor).................. 688
Motor insulation resistance (motor).................. 688
Select axis for servomotor insulation
degradation detection (PLC axis) .............. 623
Select axis for servomotor insulation
degradation detection ................................ 626
Select spindle for motor insulation
degradation detection ................................ 624
Servomotor insulation degradation
detection in progress (PLC axis)................ 349
Servomotor insulation degradation
detection in progress ................................. 351
Spindle motor insulation degradation
detection in progress ................................. 349
DIO card information ............................................. 283
Direct screen selection.......................................... 543
Display changeover $1 to $8................................. 366
Display lock ........................................................... 427
Display tool selection parameter ........................... 612
Displayed screen No. ............................................ 527
Door interlock spindle speed clamp ...................... 471
Door open enable.................................................. 237
Door open I ........................................................... 375
Door open II .......................................................... 470
Door open signal input (spindle speed monitor).... 470
Droop cancel request n-th axis ............................. 392
Dry run invalid....................................................... 472
Dry run .................................................................. 412
E
E number of smart safety observation error
(system common)...................................... 669
Each axis in-position n-th axis .............................. 188
Each axis manual feedrate B n-th axis ................. 589
Each axis manual feedrate B valid ....................... 447
Each axis reference position selection ................. 569
EcoMonitorLight connection:
Acquired data .................................................. 341
Completion bit.................................................. 340
Completion status............................................ 341
Read start bit ................................................... 621
Register address ............................................. 621
Size of data to read ......................................... 621
Station #1 to #16 consumed power ................. 339
Station #1 to #16 maximum number of
successive reception errors....................... 340
Station #1 to #16 maximum number of
successive transmission errors ................. 340
Station #1 to #16 number of
reception errors ......................................... 340
Station #1 to #16 number of
transmission errors.................................... 340
Station #1 to #16 regenerated power .............. 339
Station No........................................................ 621
Edit/search window displayed............................... 247
Edit/Search ........................................................... 486
Emergency stop cause ......................................... 282
Encoder 1 arbitrary pulse 1................................... 553
Encoder 1 arbitrary pulse 2................................... 553
Encoder 1 arbitrary pulse selection ...................... 374
Encoder 1 arbitrary pulse valid ............................. 375
Encoder 2 arbitrary pulse 1................................... 553
Encoder 2 arbitrary pulse 2................................... 553
Encoder 2 arbitrary pulse selection ...................... 374
Encoder 2 arbitrary pulse valid ............................. 375
Encoder selection ................................................. 568
Error detection ...................................................... 413
Error temporary cancel ......................................... 516
Exclude spindle..................................................... 518
Ext. machine coordinate system offset data
illegal n-th axis........................................... 187
Ext. machine coordinate system offset data
n-th axis..................................................... 589
External brake SBT incomplete (control axis)....... 654
External brake SBT start (control axis) ................. 634
External deceleration- n-th axis ............................ 383
External deceleration+ n-th axis ........................... 383
External encoder 1:
Position output clear request..................... 521
External encoder 1: Position output...................... 691
External search block No...................................... 564
External search device No.................................... 563
External search finished ....................................... 202
External search program No................................. 563
External search sequence No............................... 563
External search status .......................................... 291
External search strobe.......................................... 418
External search:
Program return complete status ................ 291
External search: Program return completed ......... 237
External search: Program return........................... 456