Mitsubishi Electric M80V Series Manual page 778

Operation trigger .............................................. 519
Operator ID ...................................................... 341
Power consumption amount ............................ 614
Power ON time................................................. 617
Power regeneration amount............................. 614
Program number at alarm ................................ 617
Program number at machining start................. 613
Sending user arbitrary information ................... 246
Serial number................................................... 341
Spindle 1 load .................................................. 618
Spindle 1 maximum load.................................. 613
Spindle 2 load value......................................... 619
Spindle 2 maximum load.................................. 614
Subprogram number at alarm .......................... 618
Time of alarm occurrence ................................ 617
Tool length offset 1 to 5 ................................... 615
Tool length offset ............................................. 619
Tool length wear amount 1 to 5 ....................... 616
Tool length wear amount ................................. 620
Tool life 1 to 5 .................................................. 616
Tool life ............................................................ 620
Tool number 1 to 5........................................... 614
Tool number ..................................................... 619
Tool offset number 1 to 5 ................................. 615
Tool offset number ........................................... 619
Tool radius offset 1 to 5 ................................... 615
Tool radius offset ............................................. 619
Tool radius wear amount 1 to 5 ....................... 616
Tool radius wear amount ................................. 620
User arbitrary information send request........... 457
User area C1 at alarm...................................... 685
User area C1 at machining end ....................... 685
User area L1 to L10 at alarm ........................... 686
User area L1 to L10 at machining end ............. 685
Mirror image n-th axis ........................................... 382
Miscellaneous function command high-speed output:
2nd M function finish 1 to 4........................ 485
Miscellaneous function command high-speed output:
M function finish 1 to 4............................... 482
Miscellaneous function command high-speed output:
S function finish 1 to 8 ............................... 483
Miscellaneous function command high-speed output:
T function finish 1 to 4................................ 484
Miscellaneous function lock .................................. 439
Mixed control (cross axis control) request
n-th axis ..................................................... 395
Motion command completion ................................ 200
Motion control release:
Implementation check by function ............. 350
Motion control release: Valid/Invalid status........... 350
Motor brake SBT incomplete (control axis) ........... 655
Motor brake SBT start (control axis) ..................... 636
Motor load current n-th axis .................................. 316
Motor rotation speed n-th axis............................... 316
Multi-analog input ch n .......................................... 693
Multi-analog input status ch n ............................... 694
Multiple-spindle control I: Selected spindle No. .... 578
Multi-point orientation position data ...................... 595
Multi-step speed monitor selected speed output... 285
N
NC alarm 1 ............................................................ 226
NC alarm 2 (Servo alarm) ..................................... 227
NC alarm 3 (Program error) .................................. 227
NC alarm 4 (Operation error) ................................ 228
NC alarm 5 ............................................................ 233
NC axis control selection n-th axis ........................ 397
NC axis up-to-speed n-th axis .............................. 183
NC axis/PLC axis switchover invalid status .......... 190
NC axis/PLC axis switchover n-th axis
in process .................................................. 190
NC axis/PLC axis switchover request................... 402
NC reset 1............................................................. 414
NC reset 2............................................................. 414
NC warning (Servo warning)................................. 228
Near reference position
(per reference position) ............................. 300
Near reference position n-th axis.......................... 180
Near set position................................................... 335
Near-point dog ignored ......................................... 534
New tool change ................................................... 225
No. of error occurrences n-th ch ........................... 336
No. of work machining (current value) .................. 303
No. of work machining (maximum value).............. 303
No. of work machining over .................................. 230
Number of registered tool life control tools ........... 309
O
Operation parameter selection 1, 2 ...................... 601
Operation start ...................................................... 599
Operator message I/F 1 to 4................................. 539
Operator message I/F........................................... 567
Option status export to PLC.................................. 335
Optional block skip m............................................ 435
OT ignored............................................................ 533
Output OFF check request ................................... 646
Override cancel..................................................... 438
P
Pallet program registration Ext. workpiece
coordinate transfer completion .................. 172
Pallet program registration Ext. workpiece
coordinate transfer ready .......................... 365
Phase offset request............................................. 515
Phase shift calculation request ............................. 514
PLC axis 1st to 3rd handle valid ........................... 359
PLC axis alarm/warning No. n-th axis................... 290
PLC axis control buffering mode
information address................................... 552
PLC axis control buffering mode valid .................. 360
PLC axis control information address n-th axis .... 552
PLC axis control valid n-th axis............................. 378
PLC axis indexing control command 1 ................. 602
PLC axis indexing control command 2 ................. 598
PLC axis indexing control command 3 ................. 598
PLC axis indexing control command 4 ................. 597
PLC axis indexing control status 1........................ 330
PLC axis indexing control status 2........................ 328
PLC axis indexing control status 3........................ 328
PLC axis indexing control status 4........................ 328
PLC axis near point detection n-th axis ................ 359
PLC axis near-point dog ignored .......................... 535
PLC axis OT ignored ............................................ 534
PLC coil changeover............................................. 511
PLC emergency stop ............................................ 429
PLC interrupt program No..................................... 562
PLC interrupt......................................................... 430
PLC main scan time.............................................. 281
PLC skip 1 to 8 ..................................................... 370
PLC switch non-display ........................................ 672
Position loop in-position........................................ 256
Position switch 1 to 15 .......................................... 328
Position switch 1 to 24 .......................................... 277
Position switch n interlock..................................... 525