Mitsubishi Electric M80V Series Manual page 628

M800V/M80V Series PLC Interface Manual
4 Explanation of Interface Signals
4.4 PLC Output Signals (Data Type: R***)
Cont. Signal name
MES interface library:
A
Tool offset number 1 to 5
[Function]
The tool offset number is stored here.
[Operation]
The tool offset number commanded by the T command is automatically set when machining is completed.
Up to five tool offset number histories from the latest are set in the R registers "Tool offset number 1" to "Tool offset
number 5".
The latest is set in the R register "Tool offset number 1".
Compensation number is set for the machining center system, or tool length offset number is set for the lathe system.
When MES interface library function is invalid, this signal is set to "0".
Cont. Signal name
MES interface library:
A
Tool length offset 1 to 5
[Function]
The tool length offset amount (M system) or the X axis tool length offset amount (L system) is stored here.
[Operation]
The tool length offset amount commanded by the T command is automatically set when machining is completed.
Up to five tool length offset histories from the latest are set in the R registers "Tool length offset 1" to "Tool length offset 5".
The latest is set in the R register "Tool length offset 1".
For M system, offset amount (for offset type I), length dimension (for offset type II), or Z axis tool length offset amount (for
offset type III) is displayed. For L system, X axis tool length offset amount is displayed.
"0" is set when the tool length offset amount cannot be set, such as when the tool number is not designated.
The unit is [μm].
When MES interface library function is invalid, this signal is set to "0".
Cont. Signal name
MES interface library:
A
Tool radius offset 1 to 5
[Function]
The tool radius compensation amount (M system) or the tool nose radius compensation amount (L system) is stored here.
[Operation]
The tool radius compensation amount when T command was issued is automatically set when machining is completed.
Up to five tool radius offset histories from the latest are set in the R registers "Tool radius offset 1" to "Tool radius offset 5".
The latest is set in the R register "Tool radius offset 1".
For M system, offset amount (for offset type I), radius dimension (for offset type II), or tool nose radius offset (for offset
type III) is displayed. For L system, tool nose radius offset is displayed.
"0" is set when the tool radius compensation amount cannot be set, such as when the tool number is not designated.
The unit is [μm].
When MES interface library function is invalid, this signal is set to "0".
Abbrev. $1 $2
R14742 R14992 R15242
to to
R14746 R14996 R15246
Abbrev. $1 $2
R14748, R14998, R15248,
9 to 9 to
R14756, R15006, R15256,
7 7
Abbrev. $1 $2
R14758, R15008, R15258,
9 to 9 to
R14766, R15016, R15266,
7 7
615
$3 $4 $5 $6
R15492 R15742 R15992
to to to to
R15496 R15746 R15996
$3 $4 $5 $6
R15498, R15748, R15998,
9 to 9 to 9 to 9 to
R15506, R15756, R16006,
7 7 7 7
$3 $4 $5 $6
R15508, R15758, R16008,
9 to 9 to 9 to 9 to
R15516, R15766, R16016,
7 7 7 7
$7 $8
R16242 R16492
to to
R16246 R16496
$7 $8
R16248, R16498,
9 to 9 to
R16256, R16506,
7 7
$7 $8
R16258, R16508,
9 to 9 to
R16266, R16516,
7 7
IB-1501616-D