Mitsubishi Electric M80V Series Manual page 629

M800V/M80V Series PLC Interface Manual
4 Explanation of Interface Signals
4.4 PLC Output Signals (Data Type: R***)
Cont. Signal name
MES interface library:
A
Tool length wear amount 1 to 5
[Function]
The tool length wear amount (M system) or the X axis tool wear amount (L system) is stored here.
[Operation]
The tool length wear amount is automatically set when a T command is commanded. Up to five tool length wear amount
histories from the latest tool length wear amount are set in the R register "Tool length wear amount 1" to "Tool length wear
amount 5". The latest is set in the R register "Tool length wear amount 1".
For M system, compensation amount (for compensation type I), length wear (for compensation type II), or Z axis tool wear
(for compensation type III) is displayed. For L system, X axis tool wear is displayed.
"0" is set when the tool length wear amount cannot be set, such as when the tool number is unspecified. The unit is [μm].
When MES interface library function is invalid, this signal is set to "0".
Cont. Signal name
MES interface library:
A
Tool radius wear amount 1 to 5
[Function]
The tool radius wear amount (M system) or the X axis tool radius wear amount (L system) is stored here.
[Operation]
The tool radius wear amount when T command is issued is automatically set. Up to five tool radius wear amount histories
from the latest tool radius wear amount are set in the R register "Tool radius wear amount 1" to "Tool radius wear amount
5". The latest is set in the R register "Tool radius wear amount1".
For M system, compensation amount (for compensation type I), radius wear (for compensation type II), or tool nose radius
wear (for compensation type III) is displayed. For L system, tool nose radius wear is displayed.
"0" is set when the tool radius wear amount cannot be set, such as when the tool number is unspecified. The unit is [μm].
When MES interface library function is invalid, this signal is set to "0".
Cont. Signal name
MES interface library:
A
Tool life 1 to 5
[Function]
The tool lives data at the time of machining completion are stored here.
[Operation]
The tool lives (cumulative cutting hours or cumulative number of cuttings) for the tools set in the R register "Tool number
1" to "Tool number 5" (R14732 to R14741) are automatically set at the time of the machining completion.
Five tool life histories from the latest tool life are set in the R register "Tool life 1" to R register "Tool life 5". The latest is set
in the R register "Tool life 1".
The tool life is set only when the tool life management I is valid for both M and L systems.
"0" is set when tool life management II or III is valid or tool life management function is invalid.
Data type depends on the setting of management method for M system. Specify the data type in minutes in the case of
usage time and specify it by the number of times in the case of usage count. Specify usage time in minutes for L system.
"0" is set when tool lives are unsettable, such as when the tool numbers are unspecified.
When MES interface library function is invalid, this signal is set to "0".
IB-1501616-D
Abbrev. $1 $2
R14768, R15018, R15268,
9 to 9 to
R14776, R15026, R15276,
7 7
Abbrev. $1 $2
R14778, R15028, R15278,
9 to 9 to
R14786, R15036, R15286,
7 7
Abbrev. $1 $2
R14788, R15038, R15288,
9 to 9 to
R14796, R15046, R15296,
7 7
616
$3 $4 $5 $6
R15518, R15768, R16018,
9 to 9 to 9 to 9 to
R15526, R15776, R16026,
7 7 7 7
$3 $4 $5 $6
R15528, R15778, R16028,
9 to 9 to 9 to 9 to
R15536, R15786, R16036,
7 7 7 7
$3 $4 $5 $6
R15538, R15788, R16038,
9 to 9 to 9 to 9 to
R15546, R15796, R16046,
7 7 7 7
$7 $8
R16268, R16518,
9 to 9 to
R16276, R16526,
7 7
$7 $8
R16278, R16528,
9 to 9 to
R16286, R16536,
7 7
$7 $8
R16288, R16538,
9 to 9 to
R16296, R16546,
7 7