Mitsubishi Electric M80V Series Manual page 255

M800V/M80V Series PLC Interface Manual
4 Explanation of Interface Signals
4.1 PLC Input Signals (Bit Type: X***)
Cont. Signal name
3D manual feed (JOG, INC): Tool axis
A
coordinate system selected
3D manual feed (JOG, INC): Table co-
A
ordinate system selected
3D manual feed (JOG, INC): Feature
A
coordinate system selected
[Function]
This signal indicates the coordinate system in which the 3D manual feed is carried out by the jog or incremental feed.
Jog feed or incremental feed is carried out on the coordinate system for which this signal is ON.
[Operation]
This signal turns ON when:
 The signal (YD18 to YD1A) to select the coordinate system for the 3D manual feed (JOG, INC) is turned ON during jog
mode or incremental mode.
This signal turns OFF when:
 The signal (YD18 to YD1A) to select the coordinate system for the 3D manual feed (JOG, INC) is turned OFF.
 The jog feed mode or incremental feed mode is turned OFF.
[Related signals]
(1) In jog mode (JO: XC00)
(2) In incremental mode (SO: XC02)
(3) 3D manual feed (JOG, INC): Tool axis coordinate system selection (MJCT: YD18)
(4) 3D manual feed (JOG, INC): Table coordinate system selection (MJCB: YD19)
(5) 3D manual feed (JOG, INC): Feature coordinate system selection (MJCF: YD1A)
(6) In tool center point rotation (TCPRS: XD27)
Cont. Signal name
3D manual feed (1st handle): Tool axis
A
coordinate system selected
3D manual feed (1st handle): Table co-
A
ordinate system selected
3D manual feed (1st handle): Feature
A
coordinate system selected
[Function]
This signal indicates the coordinate system in which the 3D manual feed is carried out on the 1st handle axis.
The feed on the 1st handle axis is carried out on the coordinate system for which this signal is ON.
[Operation]
This signal turns ON when:
 The 1st handle feed is valid, the axis is selected and the signal (YD1B to YD1D) to select the coordinate system for the
3D manual feed (1st handle) is turned ON.
This signal turns OFF when:
 The signal (YD1B to YD1D) to select the coordinate system for the 3D manual feed (1st handle) is turned OFF.
 The "1st handle valid" signal is turned OFF.
 The signal to select the 1st handle axis is turned OFF.
[Related signals]
(1) 1st handle axis selection code (HS11 to HS116: YC40 to 4)
(2) 1st handle valid (HS1S: YC47)
(3) 3D manual feed (1st handle): Tool axis coordinate system selection (MH1CT: YD1B)
(4) 3D manual feed (1st handle): Table coordinate system selection (MH1CB: YD1C)
(5) 3D manual feed (1st handle): Feature coordinate system selection (MH1CF: YD1D)
(6) In tool center point rotation (TCPRS: XD27)
IB-1501616-D
Abbrev. $1 $2
MJST XD18 XE58 XF98
MJSB XD19 XE59 XF99
MJSF XD1A XE5A XF9A
Abbrev. $1 $2
MH1ST XD1B XE5B XF9B
MH1SB XD1C XE5C XF9C
MH1SF XD1D XE5D XF9D
242
$3 $4 $5 $6
X10D8 X1218 X1358
X10D9 X1219 X1359
X10DA X121A X135A
$3 $4 $5 $6
X10DB X121B X135B
X10DC X121C X135C
X10DD X121D X135D
$7 $8
X1498 X15D8
X1499 X15D9
X149A X15DA
$7 $8
X149B X15DB
X149C X15DC
X149D X15DD