Mitsubishi Electric M80V Series Manual page 158

M800V/M80V Series PLC Interface Manual
2 Input/Output Signals with Controller
2.7 Classified for Each Application
[CNC -> PLC]
1stSP 2ndSP 3rdSP
R6500 R6550 R6600 R6650
R6501 R6551 R6601 R6651
R6502 R6552 R6602 R6652
R6503 R6553 R6603 R6653
R6504 R6554 R6604 R6654
R6505 R6555 R6605 R6655
R6506 R6556 R6606 R6656
R6507 R6557 R6607 R6657
R6508 R6558 R6608 R6658
R6514 R6564 R6614 R6664
R6515 R6565 R6615 R6665
R6516 R6566 R6616 R6666
R6517 R6567 R6617 R6667
R6518 R6568 R6618 R6668
R6519 R6569 R6619 R6669
R6520 R6570 R6620 R6670
R6521 R6571 R6621 R6671
R6522 R6572 R6622 R6672
R6523 R6573 R6623 R6673
R6525 R6575 R6625 R6675
R6526 R6576 R6626 R6676
R6527 R6577 R6627 R6677
R6528 R6578 R6628 R6678
R6529 R6579 R6629 R6679
R6532 R6582 R6632 R6682
R6533 R6583 R6633 R6683
R6534 R6584 R6634 R6684
R6535 R6585 R6635 R6685
R6536 R6586 R6636 R6686
R6537 R6587 R6637 R6687
R6538 R6588 R6638 R6688
R6539 R6589 R6639 R6689
R6541 R6591 R6641 R6691
R6542 R6592 R6642 R6692
Device No.
4thSP 5thSP 6thSP 7thSP
R6700 R6750 R6800
R6701 R6751 R6801
R6702 R6752 R6802
R6703 R6753 R6803
R6704 R6754 R6804
R6705 R6755 R6805
R6706 R6756 R6806
R6707 R6757 R6807
R6708 R6758 R6808
R6714 R6764 R6814
R6715 R6765 R6815
R6716 R6766 R6816
R6717 R6767 R6817
R6718 R6768 R6818
R6719 R6769 R6819
R6720 R6770 R6820
R6721 R6771 R6821
R6722 R6772 R6822
R6723 R6773 R6823
R6725 R6775 R6825
R6726 R6776 R6826
R6727 R6777 R6827
R6728 R6778 R6828
R6729 R6779 R6829
R6732 R6782 R6832
R6733 R6783 R6833
R6734 R6784 R6834
R6735 R6785 R6835
R6736 R6786 R6836
R6737 R6787 R6837
R6738 R6788 R6838
R6739 R6789 R6839
R6741 R6791 R6841
R6742 R6792 R6842
8thSP Abbrev.
R6850 Spindle command rotation speed input (L)
R6851 Spindle command rotation speed input (H)
R6852 Spindle command final data (rotation speed) (L)
R6853 Spindle command final data (rotation speed) (H)
R6854 Spindle command final data (12-bit binary) (L)
R6855 Spindle command final data (12-bit binary) (H)
R6856 Spindle actual speed (L)
R6857 Spindle actual speed (H)
R6858
Optimum acceleration/deceleration estimat-
R6864
ed inertia ratio (spindle)
Optimum acceleration/deceleration param-
R6865
eter group currently selected (spindle)
Spindle synchronization: Phase error /Hob axis
R6866
delay angle
Spindle synchronization: Maximum phase error/
R6867
Maximum hob axis delay angle
R6868 Spindle synchronization: Phase offset data
R6869 Spindle synchronization: Phase error monitor
Spindle synchronization: Phase error monitor
R6870
(lower limit)
Spindle synchronization: Phase error monitor
R6871
(upper limit)
R6872 Spindle synchronization: Phase error 1
R6873 Spindle synchronization: Phase error 2
R6875 Spindle motor load ratio
SP-
R6876 Spindle temperature output
TEMP
R6877 Spindle actual machining time
Load monitor I: Spindle cutting torque out-
R6878
put value
R6879 Spindle alarm/warning No.
R6882 Synchronous tapping Current error width (L)
R6883 Synchronous tapping Current error width (H)
R6884 Synchronous tapping Maximum error width (L)
R6885 Synchronous tapping Maximum error width (H)
R6886 Synchronous tapping Current error angle (L)
R6887 Synchronous tapping Current error angle (H)
R6888 Synchronous tapping Maximum error angle (L)
R6889 Synchronous tapping Maximum error angle (H)
Load monitoring I: Estimated spindle disturbance
R6891
torque output
R6892 Load monitoring I: Effective spindle torque output
145
Signal name
▲
▲
▲
▲
IB-1501616-D