Mitsubishi Electric M80V Series Manual page 773

Basic point setting................................................. 604
Basic position -> upper dead point path flag......... 223
Battery alarm ........................................................ 167
Battery drop cause................................................ 280
Battery warning..................................................... 166
BiSS encoder I/F: Communication status ............. 695
BiSS encoder I/F: Encoder 1 data output 1 to 4 ... 695
Block start interlock............................................... 411
Board reset ........................................................... 165
Bottom dead point -> upper dead point
path flag..................................................... 223
Buzzer sound control: Buzzer ON ........................ 520
C
C axis selection..................................................... 568
Chamfering ........................................................... 416
Chopping compensation update prevented .......... 223
Chopping compensation update prevention
request ...................................................... 469
Chopping control data address............................. 569
Chopping error No. ............................................... 296
Chopping override ................................................ 559
Chopping parameter valid..................................... 434
Chopping .............................................................. 432
Chuck close confirmation...................................... 263
Chuck close .......................................................... 517
Circular feed in manual mode
Current position H ..................................... 309
Circular feed in manual mode
Current position V...................................... 309
Circular feed in manual mode
gradient/arc center H data......................... 588
Circular feed in manual mode
gradient/arc center V data ......................... 588
Circular feed in manual mode
Operation mode data................................. 585
Circular feed in manual mode
Reference point H data ............................. 586
Circular feed in manual mode
Reference point V data.............................. 586
Circular feed in manual mode
travel range H (-) data ............................... 587
Circular feed in manual mode
travel range H (+) data .............................. 587
Circular feed in manual mode
travel range V (-) data ............................... 587
Circular feed in manual mode
travel range V (+) data............................... 587
Circular feed in manual mode valid ...................... 449
Clamp command n-th axis .................................... 187
Clamp completion n-th axis .................................. 398
CLC: Maximum load ............................................. 355
CLC: Minimum load .............................................. 355
CLC: Spindle selection ......................................... 627
Clock data Date/Hour ........................................... 279
Clock data Minute/Second.................................... 279
Clock data Year/Month ......................................... 279
CNC completion standby status ........................... 297
CNC software version code .................................. 279
Collecting diagnosis data stop .............................. 364
Collecting diagnosis data...................................... 169
Connection status of each channel RIO1, RIO2... 337
Connection status of each channel RIO3, RIO4... 337
Constant torque control:
Axis under constant torque/proportional
torque stopper control ............................... 308
Constant torque control:
Constant torque droop cancel
axis status ..................................................308
Constant torque control:
Constant torque droop cancel
request axis................................................581
Constant torque control:
Constant torque/proportional torque
stopper control request axis .......................581
Contactor shutoff test ............................................370
Control axis detachment 2 n-th axis ......................394
Control axis detachment n-th axis .........................380
Control unit temperature........................................281
Controller ready completion ..................................195
Controller ready completion ..................................333
Coordinate rotation by parameter:
Coordinate switch for manual feed ............449
Coordinate rotation by parameter:
Manual feed coordinate system .................217
CRC warning channel RIO1, RIO2........................338
CRC warning channel RIO3, RIO4........................338
CRT changeover completion.................................363
Current detection...................................................250
Current limit changeover n-th axis.........................391
Current limit changeover .......................................575
Current limit mode 1 ..............................................466
Current limit mode 2 ..............................................466
Current limit reached n-th axis ..............................182
Current spatial error compensation value
(1st rotary axis) ..........................................351
Current spatial error compensation value
(2nd rotary axis) .........................................351
Current spatial error compensation value
(orthogonal coordinate height axis)............351
Current spatial error compensation value
(orthogonal coordinate horizontal axis) ......351
Current spatial error compensation value
(orthogonal coordinate vertical axis) ..........351
Cutting block start interlock ...................................412
Cutting feed override code m ................................442
Cutting feedrate override method selection...........443
D
Data I/O register for MES interface library
(Alarm number 1) ............................................681
(Alarm number 2) ............................................681
(Alarm number 3) ............................................681
(Alarm number 4) ............................................681
(Arbitrary user area C1)...................................684
(Arbitrary user area L1 to L10) ........................685
(Arbitrary user area S1 to S20) .......................685
(B number at alarm) ........................................682
(B number at machining start) .........................678
(Common user area C1)..................................676
(Common user area L1 to L10) .......................677
(Cycle time) .....................................................677
(G code modal)................................................682
(Line number) ..................................................676
(Machine type).................................................676
(Machining end time).......................................677
(Machining start time)......................................677
(N number at alarm) ........................................682
(N number at machining start).........................678
(NC unit number).............................................676
(Number of machined workpieces)..................679
(Operator ID) ...................................................676
(Power consumption amount) .........................678