Mitsubishi Electric M80V Series Manual page 57

M800V/M80V Series PLC Interface Manual
2 Input/Output Signals with Controller
2.2 PLC Input Signals (Data Type: R***)
Device No.
$1 $2 $3 $4
R644 R844 R1044 R1244 R1444 R1644 R1844 R2044
R645 R845 R1045 R1245 R1445 R1645 R1845 R2045
R646 R846 R1046 R1246 R1446 R1646 R1846 R2046
R647 R847 R1047 R1247 R1447 R1647 R1847 R2047
R648 R848 R1048 R1248 R1448 R1648 R1848 R2048
R649 R849 R1049 R1249 R1449 R1649 R1849 R2049
R650 R850 R1050 R1250 R1450 R1650 R1850 R2050
R651 R851 R1051 R1251 R1451 R1651 R1851 R2051
Device No.
$1 $2 $3 $4
R652 R852 R1052 R1252 R1452 R1652 R1852 R2052
R653 R853 R1053 R1253 R1453 R1653 R1853 R2053
R654 R854 R1054 R1254 R1454 R1654 R1854 R2054
R655 R855 R1055 R1255 R1455 R1655 R1855 R2055
R656 R856 R1056 R1256 R1456 R1656 R1856 R2056 RPAROUT Rotary axis configuration parameter output
R657 R857 R1057 R1257 R1457 R1657 R1857 R2057
R658 R858 R1058 R1258 R1458 R1658 R1858 R2058
R659 R859 R1059 R1259 R1459 R1659 R1859 R2059
Device No.
$1 $2 $3 $4
R660 R860 R1060 R1260 R1460 R1660 R1860 R2060 RSWRK
R661 R861 R1061 R1261 R1461 R1661 R1861 R2061 RSSRF
R662 R862 R1062 R1262 R1462 R1662 R1862 R2062 CAXSVFO
R663 R863 R1063 R1263 R1463 R1663 R1863 R2063 SPGNCI
R664 R864 R1064 R1264 R1464 R1664 R1864 R2064
R665 R865 R1065 R1265 R1465 R1665 R1865 R2065
R666 R866 R1066 R1266 R1466 R1666 R1866 R2066
R667 R867 R1067 R1267 R1467 R1667 R1867 R2067
Device No.
$1 $2 $3 $4
R668 R868 R1068 R1268 R1468 R1668 R1868 R2068 SVESTAF
R669 R869 R1069 R1269 R1469 R1669 R1869 R2069 SVESTST
R670 R870 R1070 R1270 R1470 R1670 R1870 R2070 ITF3CHW
R671 R871 R1071 R1271 R1471 R1671 R1871 R2071
R672 R872 R1072 R1272 R1472 R1672 R1872 R2072 ITF3CHAL
R673 R873 R1073 R1273 R1473 R1673 R1873 R2073
R674 R874 R1074 R1274 R1474 R1674 R1874 R2074 ITF3-
R675 R875 R1075 R1275 R1475 R1675 R1875 R2075
IB-1501616-D
$5 $6 $7 $8
$5 $6 $7 $8
$5 $6 $7 $8
$5 $6 $7 $8
44
Abbrev.
Machining mode state
Thread recutting status
Thread recutting execution status
Thread recutting spindle No.
Thread recutting lead axis No.
Abbrev.
TLMSL- Sensor ON Tool length compensation No.
NO1 (BCD output)
TLMSWN Sensor ON Tool wear compensation No.
O1 (BCD output)
Compensation data update Tool length compensa-
TLMSL-
tion No.
NO2
(BCD output)
Compensation data update Tool wear compensa-
TLMSWN
tion No.
O2
(BCD output)
Ext. machine coordinate: Number input compensa-
tion offset valid axis
Abbrev.
R-Navi: Selected workpiece No.
R-Navi: Selecting machine surface number
Spindle position control (spindle/C axis control):
Servo OFF state during Spindle/C axis mode n-th
axis
Spindle position control (spindle/C axis control):
Position loop gain switch at C axis mode in prog-
ress
Abbrev.
Optimum acceleration/deceleration selection:
NC axis estimated resonance frequency (in esti-
mating inertia)
Optimum acceleration/deceleration selection: NC
axis estimated inertia state
Interference check III: Entry in interference warn
GSLD area solid information
Interference check III: Interference detection solid
SLD information
Interference check III: Entry in interference alarm
TRALSLD area solid information
Signal name
▲
Signal name
▲
▲
▲
▲
▲
Signal name
▲
▲
Signal name
▲
▲