IDEC MICROSmart FC6A Series Ladder Programming Manual page 603

values
change timer 4-9
changing 4-19
restoring 4-19
program branching
instructions 13-1
using with SOTU/SOTD instructions 13-2
using with timer instruction 13-2
programming
DI or EI using WindLDR 15-2
Programming Scripts 26-12
prohibited
instructions 4-33
ladder programs 4-33
proximity signal 18-36
pulse
input 4-24
Pulse flow totalizer (FLWP) 27-18
Pulse Monitor 18-79
Q
quit WindLDR 1-12
R
RAD 21-1
radian 21-1
RAMPL 18-27
Relational operator 26-13, 26-24
Repeat 26-12
repeat
cycles 3-6
designation 3-6
operation
ADD and SUB instructions 7-6
ANDW, ORW, and XORW instructions 8-3
data comparison instructions 6-4
DIV instruction 7-10
indirect bit move instruction 5-13
move instructions 5-3
MUL instruction 7-8
reset
input 4-24
restore timer/counter preset values 4-19
restriction on ladder programming 4-33
reverse
shift register 4-26
Reversible control 18-19, 18-32, 18-52
ROOT 7-14
rotate
left 9-8
right 9-10
ROTL 9-8
ROTR 9-10
RS232C DSR Control Signal Status 2-32
RS232C DTR Output Control Signal Option 2-34
rung 1-3, 1-4
S
s to HMS 24-10
Scale conversion instruction (SCALE) 27-1
Script (SCRPT) 26-1
Script Editor 26-8
Script Manager 26-7
Script Programming Examples 26-19
SET and RST instructions 4-3
SFR and SFRN instructions 4-24
FC6A S MICROS L
ERIES MART
SFTL 9-1
SFTR 9-3
shift
left 9-1
register
instructions 4-24
right 9-3
shift/rotate instructions 9-1
simulate operation 1-9
SIN 21-3
sine 21-3
single output instruction 4-28
SOTU and SOTD instructions 4-28
SOTU/SOTD instructions using with program branching 13-2
source
and destination devices 3-6
device 3-6
Special data register device addresses 2-16
special dates 11-16
special internal relay
for interrupt status 15-1
Special internal relay device addresses 2-4
specified date 11-16
start
WindLDR 1-1, 1-3
start/stop
operation 1-18
schematic 1-18
using power supply 1-19
using WindLDR 1-18
structure of an advanced instruction 3-6
SUB 7-1
subroutine 13-4
subtraction 7-1
SUM 7-15
sum 7-15
SWAP 10-23
T
TADD 24-1
TAN 21-5
tangent 21-5
TCCST 5-18
teaching timer 20-3
Temporary Device 26-18
time
addition 24-1
subtraction 24-5
timer
100-ms off-delay 4-11
10-ms off-delay 4-11
1-ms off-delay 4-11
1-s off-delay 4-11
accuracy 4-9
instruction using with program branching 13-2
or counter
as destination device 3-6
as source device 3-6
timer/counter
current value
store 5-18
TML, TIM, TMH, and TMS instructions 4-7
TMLO, TIMO, TMHO, and TMSO instructions 4-11
TRACE 25-15
P M
ADDER ROGRAMMING ANUAL
FC9Y-B1726
I
NDEX
I -5
NDEX