IDEC MICROSmart FC6A Series Ladder Programming Manual page 344

18: P O I
ULSE UTPUT NSTRUCTIONS
2. S1 (source 1): Control Register
S1 specifies the first data register of the data registers to use with the ARAMP1, ARAMP2, ARAMP3 or ARAMP4 instruction.
Starting from the specified data register, "2+8 x N (N: number of steps)" consecutive data registers are used.
The range of data registers that can be specified depends on the number of steps.
If the number of steps is 1, 10 words are required.
If the number of steps is 18, 146 words are required.
Specify the first data register so that the device range is not exceeded.
The steps operate with the settings that are configured when the steps start. If the settings for a step are changed after it starts
running, those changes are not reflected while the step is running.
Storage
Destination
Starting number+0
Starting number+1
Step 1 (8 words)
Starting number+2,
Starting number+3
Starting number+4
Starting number+5
Starting number+6
Starting number+7
Starting number+8
Starting number+9
Step 2 (8 words)
Starting number+10,
Starting number+11
:
Starting number+17
:
Step N (8 words)
Starting
number+2+N x 8-8
Starting
number+3+N x 8-8
:
Starting
number+9+N x 8-8
*1 The upper and lower data registers change according to the 32-bit data storage method specified.
For details, see "32-bit Data Storage" on page 3-9.
18-48
Function
Interrupt number
Reserved
Steady pulse frequency
Reserved
Frequency change time
*1
Preset value (high word)
*1
Preset value (low word)
Step options
Next step number
Steady pulse frequency
:
Next step number
Steady pulse frequency
:
Next step number
FC6A S MICROS
ERIES MART
Setting
CAN J1939 All-in-
All-in-One CPU
One CPU Module/
Module
Plus CPU Module
1 to 18
ARAMP1, ARAMP2:
15 to 100,000
ARAMP1 to ARAMP4:
(increments of 1 Hz)
15 to 100,000
ARAMP3, ARAMP4:
(increments of 1 Hz)
15 to 5,000
(increments of 1 Hz)
10 to 10,000 ms
1 to 100,000,000 pulses
0 to 3
1 to 18
ARAMP1, ARAMP2: 15 to
100,000
ARAMP1 to ARAMP4:
(increments of 1 Hz)
15 to 100,000
ARAMP3, ARAMP4:
(increments of 1 Hz)
15 to 5,000
(increments of 1 Hz)
:
1 to 18
ARAMP1, ARAMP2:
15 to 100,000
ARAMP1 to ARAMP4:
(increments of 1 Hz)
15 to 100,000
ARAMP3, ARAMP4:
(increments of 1 Hz)
15 to 5,000
(increments of 1 Hz)
:
1 to 18
L P M
ADDER ROGRAMMING ANUAL
Reference
"11. Interrupt step
number" on page 18-52
"13. Steady pulse
frequency" on page 18-53
"14. Frequency change
time" on page 18-53
"15. Preset value" on page
18-53
"16. Step options" on page
18-53
"17. Next step number" on
page 18-54
"13. Steady pulse
frequency" on page 18-53
"17. Next step number" on
page 18-54
"13. Steady pulse
frequency" on page 18-53
"17. Next step number" on
page 18-54
FC9Y-B1726
:
: