Siemens SINAMICS S110 List Manual page 1279

Digital inputs/outputs
Control Unit 305 (CU305), 2-768
Digital outputs
Control Unit 305 (CU305), 2-768
Direction limitation, 2-853
Direction reversal, 2-853
Display
Alarms, 3-966
Faults, 3-966
Display parameters, 1-13
DO, Drive Object, 1-14
Drive data sets, 2-950
Drive object, 1-14
E
EC Declaration of Conformity, Preface-7
EDS, Encoder Data Set, 2-950, 2-953
EDS, encoder data set, 1-19
Effective (parameter, C1(x), C2(x), U, T),
1-16
ENCODER, 3-968
Encoder code, A-1260
Encoder data sets, 2-950
Encoder evaluation, 2-885
Expert list, 1-23
Explanations on function diagrams, 2-753
F
Factory setting, 1-23
Fault
Acknowledgment, 3-969, 3-972
Cause, 3-972
Display, 3-966
Drive object, 3-971
Explanation of list, 3-970
Fault location, 3-971
Fault reaction, 3-967, 3-971
General information, 3-966
How to distinguish a fault from an alarm,
3-966
List of all faults, 3-975
Message value, 3-971
Name, 3-971
Number, 3-970
Number range, 3-975
Remedy, 3-972
Fault buffer, 2-944
Structure, 2-945
Fault value, 3-972
Fixed speed setpoints, 2-853
Fixed values, 2-755, 2-934
Free function blocks, 2-915
Free interconnection via BICO, 2-776
© Siemens AG 2012 All Rights Reserved
SINAMICS S110 List Manual (LH7), 06/2012, 6SL3097-4AP10-0BP3
Free interconnection, status words, 2-802
Function (parameter), 1-24
Function diagrams, Basic Operator Panel 20
(BOP20)
Control word BOP20 interconnection,
2-963
Function diagrams, basic positioner (EPOS)
Control word block selection/MDI
selection (r0108.4 = 1), 2-876
Direct setpoint input/MDI mode
(r0108.4 = 1), 2-872
Direct setpoint input/MDI mode, dynamic
values (r0108.4 = 1), 2-871
Flying referencing mode (r0108.4 = 1)
(p2597 = 1 signal), 2-867
Interpolator (r0108.4 = 1), 2-875
Jog mode (r0108.4 = 1), 2-865
Mode control (r0108.4 = 1), 2-873
Referencing/reference point approach
mode (r0108.4 = 1)
(p2597 = 0-signal), 2-866
Status word 1 (r0108.3 = 1, r0108.4 = 1),
2-877
Status word 2 (r0108.3 = 1, r0108.4 = 1),
2-878
Status word, active traversing block/MDI
active (r0108.4 = 1), 2-879
Travel to fixed stop (r0108.4 = 1), 2-870
Traversing blocks mode (r0108.4 = 1),
2-869
Traversing blocks, external block change
mode (r0108.4 = 1), 2-868
Traversing range limits (r0108.4 = 1),
2-874
Function diagrams, brake control
Basic brake control (r0108.14 = 0), 2-830
Extended brake control, open/close brake
(r0108.14 = 1), 2-832
Extended brake control, signal outputs
(r0108.14 = 1), 2-833
Extended brake control, zero-speed
detection (r0108.14 = 1), 2-831
Function diagrams, CANopen interface
Control word, CANopen, 2-960
Receive telegram, free PDO mapping
(p8744 = 2), 2-956
Receive telegram, Predefined Connection
Set (p8744 = 1), 2-957
Send telegram, free PDO mapping
(p8744 = 2), 2-958
Send telegram, Predefined Connection
Set (p8744 = 1), 2-959
Status word, CANopen, 2-961
Index
C-1279