Hyundai Sonata 1991 Shop Manual page 36

GENERAL
Description
Specification
Limit
0.1 mm (0.004 in.)
0.1 mm (0.004 in.)
0.8 mm (0.031 in.)
0.8 mm (0.031 in.)
1.0 mm (0.039 in.)
0.03-0.07 mm (0.0012-0.0028 in.)
0.02-0.06 mm (0.0008-0.0024 in.)
0.25 mm (0.010 in.), 0.50 mm (0.020 in.)
0.75 mm (0.030 in.), 1.00 mm (0.040 in.), over size
0.25-0.40 mm (0.0098-0.0157 in.)
0.20-0.35 mm (0.0079-0.0138 in.)
0.20-0.70 mm (0.0079-0.0276 in.)
Ring end gap
NO.1
No.2
Oil ring side rail
Ring side clearance
No.1
No.2
Rings for service
20.974-20.985 mm (0.8257-0.8262 in.)
7,355-17,162 N (750-1,750 kg, 1,653-3,858 Ib)
0.10-0.25 mm (0.0039-0.0098 in.) 0.4 mm (0.004 in.)
Steel
Hardening and tempering
56.980-56.995 mm (2.2433-2.2439 in.)
44.980-44.995 mm (1.7709-1.7715 in.)
Max 0.015 mm (0.0006 in.)
Max 0.005 mm (0.0002 in.)
Connecting rod
Piston pin bore diameter
Piston pin press-in load
Thrust clearance (Big end)
Crankshaft
Material
Treatment
Journal O.D.
Pin O.D.
Out-of-roundness of journal and pin
Taper of journal and pin
Oil clearance
Main bearing journal
Connecting rod journal
Thrust taken by
End play
Bearings for service
(Connecting rod, crankshaft)
Cylinder block
Material
Water jacket
Cylinder bore
Overall height
Flatness of gasket surface
Out-of-roundness and taper
Oil pump
Type
Drive mechanism
Tip clearance
Drive gear
Driven gear
Side clearance
Drive gear
Driven gear
Oil filter
Type
Engine oil
Capacity including oil filter
0.02-0.05 mm (0.0008-0.0020 in.)
0.02-0.05 mm (0.0008-0.0020 in.)
NO.3 main bearing
0.05-0.18 mm (0.0020-0.0071 in.)
0.25 mm (0.010 in.), 0.50 mm (0.20 in.)
0.75 mm (0.030 in.) undersize
Cast iron
Siamese type
86.49-86.53 mm (3.4051-3.4067 in.)
290 mm (11.4 in.)
Max. 0.05 mm (0.0020 in.)
Max. 0.01 mm (0.0004 in.)
Gear
Cogged type belt
0.16-0.21 mm (0.0063-0.0083 in.)
0.13-0.18 mm (0.0051-0.0071 in.)
0.08-0.14 mm (0.0031-0.0055 in.)
0.06-0.12 mm (0.0024-0.0047 in.)
Cartridge, full flow
3.90 lit (4.12 U.S.qts., 3.43 Imp.qts.)
-0.2 mm(-0.0079 in.)
0.25 mm (0.0098 in.)
0.25 mm (0.0098 in.)
0.25 mm (0.0098 in.)
0.25 mm (0.0098 in.)
Recommended oil (API classification) SF, SF/CC OR SG
20-5