HPE FlexNetwork HSR6800 Configuration Manual page 192
Layer 3-ip routing configuration guide
Hide thumbs
Also See for FlexNetwork HSR6800:
- Security command reference (538 pages) ,
- Configuration manual (503 pages) ,
- Command reference manual (153 pages)
Table of Contents
Advertisement
[RouterA-multiple-topology-video] acl 3002
[RouterA-multiple-topology-video] quit
[RouterA-address-family ipv4] quit
# Enable topology voice for GigabitEthernet 2/2/1, and video for GigabitEthernet 2/2/2.
[RouterA] interface gigabitethernet 2/2/2
[RouterA-GigabitEthernet2/2/2] multiple-topology video enable
[RouterA-GigabitEthernet2/2/2] quit
[RouterA] interface gigabitethernet 2/2/1
[RouterA-GigabitEthernet2/2/1] multiple-topology voice enable
[RouterA-GigabitEthernet2/2/1] quit
Configurations on other routers are similar. (Details not shown.)
Configure IS-IS MTR:
3.
# Configure Router A. Configure IS-IS to support topology voice (4000) and video (2000), and
configure GigabitEthernet 2/2/1 to support topology voice and GigabitEthernet 2/2/2 to support
video.
[RouterA] isis
[RouterA-isis-1] cost-style wide
[RouterA-isis-1] multiple-topology ipv4-unicast voice 4000
[RouterA-isis-1] multiple-topology ipv4-unicast video 2000
[RouterA-isis-1] quit
[RouterA] interface gigabitethernet 2/2/2
[RouterA-GigabitEthernet2/2/2] isis multiple-topology ipv4-unicast video
[RouterA-GigabitEthernet2/2/2] quit
[RouterA] interface gigabitethernet 2/2/1
[RouterA-GigabitEthernet2/2/1] isis multiple-topology ipv4-unicast voice
[RouterA-GigabitEthernet2/2/1] quit
# Configure Router B. Configure IS-IS to support topology video (2000), and configure
GigabitEthernet 2/2/2 and GigabitEthernet 2/2/3 to support topology video.
<RouterB> system-view
[RouterB] isis
[RouterB-isis-1] cost-style wide
[RouterB-isis-1] multiple-topology ipv4-unicast video 2000
[RouterB-isis-1] quit
[RouterB] interface gigabitethernet 2/2/2
[RouterB-GigabitEthernet2/2/2] multiple-topology video enable
[RouterB-GigabitEthernet2/2/2] isis multiple-topology ipv4-unicast video
[RouterB-GigabitEthernet2/2/2] quit
[RouterB] interface gigabitethernet 2/2/3
[RouterB-GigabitEthernet2/2/3] multiple-topology video enable
[RouterB-GigabitEthernet2/2/3] isis multiple-topology ipv4-unicast video
[RouterB-GigabitEthernet2/2/3] quit
# Configure Router C. Configure IS-IS to support topology voice (4000) and video (2000), and
configure GigabitEthernet 2/2/2 and loopback 0 to support topology voice and video.
<RouterC> system-view
[RouterC] isis
[RouterC-isis-1] cost-style wide
[RouterC-isis-1] multiple-topology ipv4-unicast voice 4000
[RouterC-isis-1] multiple-topology ipv4-unicast video 2000
[RouterC-isis-1] quit
180
Advertisement
Table of Contents
Troubleshooting
