HPE FlexNetwork HSR6800 Configuration Manual page 128
Layer 3-ip routing configuration guide
Hide thumbs
Also See for FlexNetwork HSR6800:
- Security command reference (538 pages) ,
- Configuration manual (503 pages) ,
- Command reference manual (153 pages)
Table of Contents
Advertisement
3/1
192.168.0.102
# Display routes to 120.1.1.0/24 on Router A, and you can see that Router A communicates
with Router B through the Layer 2 switch.
<RouterA> display ip routing-table 120.1.1.0 verbose
Routing Table : Public
Summary Count : 2
Destination: 120.1.1.0/24
Protocol: OSPF
Preference: 0
IpPrecedence:
NextHop: 192.168.0.100
BkNextHop: 0.0.0.0
RelyNextHop: 0.0.0.0
Tunnel ID: 0x0
BKTunnel ID: 0x0
State: Active Adv
Tag: 0
Destination: 120.1.1.0/24
Protocol: OSPF
Preference: 10
IpPrecedence:
NextHop: 10.1.1.100
BkNextHop: 0.0.0.0
RelyNextHop: 0.0.0.0
Tunnel ID: 0x0
BKTunnel ID: 0x0
State: Invalid Adv
Tag: 0
# Enable BFD debugging on Router A.
<RouterA> debugging bfd scm
<RouterA> debugging bfd event
<RouterA> debugging ospf event bfd
<RouterA> terminal debugging
# After the link over which Router A and Router B communicates through the Layer 2 switch
fails, Router A quickly detects the change on Router B.
%Nov 12 18:34:48:823 2005 RouterA BFD/5/LOG: Sess[192.168.0.102/192.168.0.100,
GE2/1/1], Sta : UP->DOWN, Diag: 1
%Nov 12 18:34:48:824 2005 RouterA RM/4/RMLOG:OSPF-NBRCHANGE: Process 1, Neighbour
192.168.0.102 (GigabitEthernet2/1/1) from Full to Down
*0.50673825 RouterA BFD/8/SCM:Sess[192.168.0.102/192.168.0.100,GE2/1/1],Oper:
Reset
*0.50673825 RouterA BFD/8/EVENT:Send sess-down Msg, [Src:192.168.0.102,
Dst:192.168.0.100, GigabitEthernet2/1/1] Protocol: OSPF
*0.50673826 RouterA RM/7/RMDEBUG:OSPF-BFD: Message Type rcv BFD down, Connect Type
direct-connect, Src IP Address 192.168.0.102, Src IFIndex 5, Dst IP Address
192.168.0.100
*0.50673827 RouterA RM/7/RMDEBUG:OSPF-BFD: Message Type delete session, Connect Type
direct-connect, Src IP Address 192.168.0.102, Src IFIndex 5, Dst IP Address
192.168.0.100
OSPF 1: Nbr 192.168.0.100 Rcv KillNbr State Full -> Down.
192.168.0.100
Up
Process ID: 0
Cost: 2
QosLcId:
Interface: GigabitEthernet2/1/1
BkInterface:
Neighbor : 0.0.0.0
Label: NULL
BKLabel: NULL
Age: 00h58m10s
Process ID: 1
Cost: 4
QosLcId:
Interface: GigabitEthernet2/1/2
BkInterface:
Neighbor : 0.0.0.0
Label: NULL
BKLabel: NULL
Age: 00h58m05s
116
1700ms
GE2/1/1
Advertisement
Table of Contents
Troubleshooting
