Connecting To Rmc500; Connecting To Ma900, Ma901; Connecting To Thv-A1; Connecting To Sa100/Sa200 - Mitsubishi Electric GT14 User Manual

53.5.11 Connecting to RMC500


Communication settings
Make the communication settings by operating the key
of the temperature controller.
Item
*1
9600bps, 19200bps, 38400bps
Communication speed
Communication protocol MODBUS
*2
MODBUS data
0 to 255 (ms)
Extesion time
[8N1]: 8bits, None, 1bit
[8N2]: 8bits, None, 2bits
*1
[8E1]: 8bits, Even, 1bit
Data bit configuration
[8E2]: 8bits, Even, 2bits
(Data bit, Parity bit, Stop bit)
[8O1]: 8bits, Odd, 1bit
[8O2]: 8bits, Odd, 2bits
*3
Device address
1 to 99
(Slave address)
Interval time*5 0 to 250 (ms)
*1 Adjust the settings with GOT settings.
*2 Set the extension time for the data interval time in the
MODBUS communication (which is lower than 24-bit time).
Set when the data time interval exceeds 24-bit time.
*3 Select the device address without overlapping with that of
other units.
*4 When the setting value is set to 0, a communication is not
made.
*5 Set the maximum time from the sending of the last character
stop bit from the GOT side until the switching of the GOT
side to the receiving status (until the temperature controller
becomes ready to send). Set as necessary.

53.5.12 Connecting to MA900, MA901


Communication settings
Make the communication settings by operating the key
of the temperature controller.
Item
*1
9600bps, 19200bps
Communication speed
[8N1]: 8bits, None, 1bit
[8N2]: 8bits, None, 2bits
*1
[8E1]: 8bits, Even, 1bit
Data bit configuration 1
[8E2]: 8bits, Even, 2bits
(Data bit, Parity bit, Stop bit)
[8O1]: 8bits, Odd, 1bit
[8O2]: 8bits, Odd, 2bits
*2
Device address
1 to 99
(Slave address)
*3
0 to 250 (ms)
Interval time
*1 Adjust the settings with GOT settings.
*2 Select the device address 1 without overlapping with that of
other units.
*3 Set the maximum time from the sending of the last character
stop bit from the GOT side until the switching of the GOT
side to the receiving status (until the temperature controller
becomes ready to send). Set as necessary.
*4 When the setting value is set to 0, a communication is not
made.
53 - 44
53. CONNECTION TO RKC TEMPERATURE CONTROLLER
53.5 Temperature Controller Side Setting
Setting range
*4
Setting range
*4

53.5.13 Connecting to THV-A1


Communication settings
Make the communication settings by operating the key
of the temperature controller.
Item
*1
9600bps (fixed)
Communication speed
Data bit: 8bits (fixed)
*1
Parity bit: None (fixed)
Data bit configuration
Stop bit : 1bit (fixed)
*2
Device address
1 to 99
(Slave address)
*3
0 to 250 (ms)
Interval time
*1 Adjust the settings of the GOT side with the temperature
controller settings.
*2 Select the device address 1 without overlapping with that of
other units.
*3 Set the maximum time from the sending of the last character
stop bit from the GOT side until the switching of the GOT
side to the receiving status (until the temperature controller
becomes ready to send). Set as necessary.
*4 When the setting value is set to 0, a communication is not
made.

53.5.14 Connecting to SA100/SA200


Communication settings
Make the communication settings by operating the key
of the temperature controller.
Item
*1
9600bps, 19200bps
Communication speed
[8N1]: 8bits, None, 1bit
[8N2]: 8bits, None, 2bits
*1
[8E1]: 8bits, Even, 1bit
Data bit configuration
[8E2]: 8bits, Even, 2bits
(Data bit, Parity bit, Stop bit)
[8O1]: 8bits, Odd, 1bit
[8O2]: 8bits, Odd, 2bits
*2
Device address
1 to 99
(Slave address)
Interval time*3 0 to 250 (ms)
*1 Adjust the settings with GOT settings.
*2 Select the device address 1 without overlapping with that of
other units.
*3 Set the maximum time from the sending of the last character
stop bit from the GOT side until the switching of the GOT
side to the receiving status (until the temperature controller
becomes ready to send). Set as necessary.
*4 When the setting value is set to 0, a communication is not
made.
Setting range
*4
Setting range
*4