Connecting To Stardom - Mitsubishi Electric GT14 User Manual

Hide thumbs Also See for GT14:
Table of Contents

Advertisement

50.2.11 Connecting to STARDOM

Make the communication settings as shown below. For
details of the communication settings, refer to the following
manual.
Peripheral Software Manual for YOKOGAWA
PLC
POINT
POINT
POINT
Connection between STARDOM and the PC for
communication settings
For the communication settings of STARDOM,
STARDOM and the PC for communication settings
must be connected to Ethernet using the Resource
Configurator (peripheral software).
COM port setting
Make the settings on the FCX Maintenance Page for
STARDOM.
1.
Select [Reboot (Maintenance Mode)] on the Reboot
screen of the FCX Maintenance Page to set the
maintenance mode.
2.
Set the COM1 port driver to be used. Execute
[JEROS Basic Setting File] from the [Edit System
Setting File] screen on the FCX Maintenance Page.
Confirm that the line of [Com1SioDriver] is as follows.
Com1SioDriver=DUONUS_SIO
3.
Set the COM1 port to be used. Execute [COM1 Port
Setting File] from the [Edit System Setting Files]
screen on the FCX Maintenance Page. Make the
settings as follows according to the communication
specifications on the setting screen.
Leave the settings as default if not listed on the
communication setting items.
(Communication setting items) ( ) in the table shows
the names on the FCX Maintenance Page.
Item
*1
Transmission speed (Baudrate)
*1
Data length (DataBitLength)
*1
Stop bit (StopBitLength)
*1
Parity bit (Parity)
Baudrate
DataBitLength
StopBitLength
Parity
FifoMode
InitialDTRState
SendFlowControlMode
ReceiveFlowControlMode
*1
Adjust the settings with GOT communication settings.
50.2.5  Communication detail settings
Set value
4800bps, 9600bps,
19200bps, 38400bps,
57600bps, 115200bps
8bits, 7bits
1bit, 2bits
none/odd/even
= *1
= *1
= *1
= *1
= YES
= ON
= CTS
= DTR
4.
Select [Reboot (Online Mode)] on the [Reboot] screen
of the FCX Maintenance Page to set the online mode.
Defining Logic POU
Define Logic POU using Logic Designer (peripheral
software), and download the project to STARDOM.
1.
Start Logic Designer and create a new project using a
template.
Use [STARDOM Serial Communication] template.
2.
Insert FA-M3 Emulator Firmware Library to the new
project.
(1)The library path inserted in the procedures above is
as follows.
(2)Insert User Library to the new project.
(3)Double-click the [SD_FCXPLCR_LIB] folder and
double-click [SD_FCXPLCR_LIB.fwl] to select it.
(4)The library path inserted in the procedures above is
as follows.
{Install Folder}\LogicDesigner\Mwt\Plc\Fw_lib\
SD_FCXPLCR_LIB\SD_FCXPLCR_LIB.fwl
3.
Insert FA-M3 Emulator User Library to the new
project.
(1)Right-click [Library] under the project tree in Logic
Designer.
(2)Right-click [Insert] and select [User Library].
(3)Double-click [SD_CFAM3R_PF.mwt] to select it.
(4)The library path inserted in the procedures above is
as follows.
{Install Folder}\LogicDesigner\Libraries\
SD_CFAM3R_PF.mwt
50. CONNECTION TO YOKOGAWA PLC
50.2 Serial Connection
48
49
50
51
52
53
54
55
50 - 19

Advertisement

Table of Contents
loading

Table of Contents