Application Parameters - Mitsubishi Electric FR-F800 Instruction Manual

Parameter List
Parameter list (by function group)
Pr.
Pr.
group
Second motor auto tuning setting/
C210 463
status
C211 574
Second motor online auto tuning
C220 458
Second motor constant (R1)
C221 459
Second motor constant (R2)
Second motor constant (L1) / d-axis
C222 460
inductance (Ld)
Second motor constant (L2) / q-axis
C223 461
inductance (Lq)
C224 462
Second motor constant (X)
C225 455
Second motor excitation current
Second motor torque current/Rated PM
C226 860
motor current
Second motor induced voltage constant
C230 738
(phi f)
C231 739
Second motor Ld decay ratio
C232 740
Second motor Lq decay ratio
C233 746
Second motor protection current level
Second starting resistance tuning
C282 741
compensation
Second motor magnetic pole detection
C285 742
pulse width
 A: Application parameters
Parameters to set a specific application.
Pr.
Pr.
group
A000 135
Electronic bypass sequence selection
A001 136
MC switchover interlock time
A002 137
Start waiting time
A003 138
Bypass selection at a fault
Automatic switchover frequency from
A004 139
inverter to bypass operation
Automatic switchover frequency range
A005 159
from bypass to inverter operation
A006 248
Self power management selection
A007 254
Main circuit power OFF waiting time
A300 592
Traverse function selection
A301 593
Maximum amplitude amount
Amplitude compensation amount
A302 594
during deceleration
Amplitude compensation amount
A303 595
during acceleration
A304 596
Amplitude acceleration time
A305 597
Amplitude deceleration time
A400 578
Auxiliary motor operation selection
A401 579
Motor connection function selection
A402 580
MC switching interlock time
A403 581
Start waiting time
Auxiliary motor connection-time
A404 582
deceleration time
Auxiliary motor disconnection-time
A405 583
acceleration time
A406 584
Auxiliary motor 1 starting frequency
A407 585
Auxiliary motor 2 starting frequency
A408 586
Auxiliary motor 3 starting frequency
A409 587
Auxiliary motor 1 stopping frequency
A410 588
Auxiliary motor 2 stopping frequency
A411 589
Auxiliary motor 3 stopping frequency
A412 590
Auxiliary motor start detection time
A413 591
Auxiliary motor stop detection time
A420 1469
Number of cleaning times monitor
A421 1470
Number of cleaning times setting
138
PARAMETERS
Refer
Name
to page
341,
351,
422
359
341,
351,
422
341
341,
351
341,
351
341
341
341,
351
351
351
351
351
351
351
Refer
Name
to page
363
363
363
363
363
363
370
370
373
373
373
373
373
373
406
406
406
406
406
406
406
406
406
406
406
406
406
406
375
375
Pr.
Pr.
group
A422 1471
Cleaning trigger selection
A423 1472
Cleaning reverse rotation frequency
Cleaning reverse rotation operation
A424 1473
time
A425 1474
Cleaning forward rotation frequency
Cleaning forward rotation operation
A426 1475
time
A427 1476
Cleaning stop time
A428 1477
Cleaning acceleration time
A429 1478
Cleaning deceleration time
A430 1479
Cleaning time trigger
A600 759
PID unit selection
A601 131
PID upper limit
A602 132
PID lower limit
A603 553
PID deviation limit
A604 554
PID signal operation selection
A605 1134
Parameter for manufacturer setting. Do not set.
A606 1135
Integral stop selection at limited
A607 1015
frequency
A610 128
PID action selection
A611 133
PID action set point
PID control automatic switchover
A612 127
frequency
A613 129
PID proportional band
A614 130
PID integral time
A615 134
PID differential time
A616 760
Pre-charge fault selection
A617 761
Pre-charge ending level
A618 762
Pre-charge ending time
A619 763
Pre-charge upper detection level
A620 764
Pre-charge time limit
A621 575
Output interruption detection time
A622 576
Output interruption detection level
A623 577
Output interruption cancel level
A624 609
PID set point/deviation input selection
A625 610
PID measured value input selection
A626 1132
Pre-charge change increment amount
C42
(934)
A630
PID display bias coefficient

C43
(934)
A631
PID display bias analog value

C44
A632 (935)
PID display gain coefficient

C45
A633 (935)
PID display gain analog value

A640 1142
Second PID unit selection
A641 1143
Second PID upper limit
A642 1144
Second PID lower limit
A643 1145
Second PID deviation limit
A644 1146
Second PID signal operation selection
A650 753
Second PID action selection
A651 755
Second PID action set point
Second PID control automatic
A652 754
switchover frequency
A653 756
Second PID proportional band
A654 757
Second PID integral time
Refer
Name
to page
375
375
375
375
375
375
375
375
375
399
378
378
378
378
378
378
378
378
378
378
378
402
402
402
402
402
378
378
378
378
378
402
399
399
399
399
378
378
378
378
378
378
378
378
378
378