Protective Function Parameter; Monitor Display And Monitor Output Signal; Earth (Ground) Fault Detection At Start - Mitsubishi Electric FR-F800 Instruction Manual

Pr.
Pr.
group
D111 386
Frequency for maximum input pulse
D200 15
Jog frequency
Multi-speed input compensation
D300 28
selection
Multi-speed setting (high speed)
D301 4
Simple Simple Simple
Multi-speed setting (middle speed)
D302 5
Simple Simple Simple
Multi-speed setting (low speed)
D303 6
Simple Simple Simple
D304
24 to
to
Multi-speed setting (4 speed to 7 speed)
27
D307
D308
232 to
Multi-speed setting (8 speed to 15
to
239
speed)
D315
 H: Protective function parameter
Parameters to protect the motor and the inverter.
Pr.
Pr.
group
H000 9
Electronic thermal O/L relay
H001 600
First free thermal reduction frequency 1
H002 601
First free thermal reduction ratio 1
H003 602
First free thermal reduction frequency 2
H004 603
First free thermal reduction ratio 2
H005 604
First free thermal reduction frequency 3
H006 607
Motor permissible load level
H010 51
Second electronic thermal O/L relay
Second free thermal reduction
H011 692
frequency 1
H012 693
Second free thermal reduction ratio 1
Second free thermal reduction
H013 694
frequency 2
H014 695
Second free thermal reduction ratio 2
Second free thermal reduction
H015 696
frequency 3
H016 608
Second motor permissible load level
H020 561
PTC thermistor protection level
PTC thermistor protection detection
H021 1016
time
H100 244
Cooling fan operation selection
H101 249

Earth (ground) fault detection at start

H102 598
Undervoltage level
H103 997
Fault initiation
H200 251
Output phase loss protection selection
H201 872

Input phase loss protection selection
H300 65
Retry selection
H301 67
Number of retries at fault occurrence
H302 68
Retry waiting time
H303 69
Retry count display erase
H320 523

Emergency drive mode selection
H321 524

Emergency drive running speed
H322 515

Emergency drive dedicated retry count
1013
Emergency drive running speed after
H323
retry reset

H324 514

Emergency drive dedicated waiting time
H400 1
Maximum frequency
H401 2
Minimum frequency
Refer
Name
to page
218
221
222
222
222
222
222
222
Refer
Name
to page
225,
Simple Simple Simple 341,
351
225
225
225
225
225
225
225,
341,
351
225
225
225
225
225
225
225
225
233
234
234
235
235
235
236
236
236
236
238
238
238
238
238
245
Simple Simple Simple
Simple Simple Simple 245
Parameter list (by function group)
Pr.
Pr.
group
H402 18
High speed maximum frequency
H420 31
Frequency jump 1A
H421 32
Frequency jump 1B
H422 33
Frequency jump 2A
H423 34
Frequency jump 2B
H424 35
Frequency jump 3A
H425 36
Frequency jump 3B
H429 552
Frequency jump range
Stall prevention operation level (Torque
H500 22
limit level)
H501 156
Stall prevention operation selection
Load characteristics measurement
H520 1480
mode
H521 1481
Load characteristics load reference 1
H522 1482
Load characteristics load reference 2
H523 1483
Load characteristics load reference 3
H524 1484
Load characteristics load reference 4
H525 1485
Load characteristics load reference 5
Load characteristics maximum
H526 1486
frequency
Load characteristics minimum
H527 1487
frequency
H530 1488
Upper limit warning detection width
H531 1489
Lower limit warning detection width
H532 1490
Upper limit fault detection width
H533 1491
Lower limit fault detection width
Load status detection signal delay time
H534 1492
/ load reference measurement waiting
time
H600 48
Second stall prevention operation level
Second stall prevention operation
H601 49
frequency
Stall prevention operation level
H610 23
compensation factor at double speed
Stall prevention operation reduction
H611 66
starting frequency
H620 148
Stall prevention level at 0 V input
H621 149
Stall prevention level at 10 V input
Voltage reduction selection during stall
H631 154
prevention operation
H730 874
OLT level setting
H800 374
Overspeed detection level
 M: Monitor display and monitor output signal
Parameters regarding the inverter's operating status. These
parameters are used to set the monitors and output signals.
Pr.
Pr.
group
M000 37
Speed display
M001 505
Speed setting reference
M002 144
Speed setting switchover
M020 170
Watt-hour meter clear
M021 563
Energization time carrying-over times
M022 268
Monitor decimal digits selection
Cumulative power monitor digit shifted
M023 891
times
M030 171
Operation hour meter clear
M031 564
Operating time carrying-over times
M040 55
Frequency monitoring reference
M041 56
Current monitoring reference
M042 866
Torque monitoring reference
M043 241
Analog input display unit switchover
M044 290
Monitor negative output selection
M050 1106
Torque monitor filter
Parameter List
Refer
Name
to page
245
246
246
246
246
246
246
246
248
248
255
255
255
255
255
255
255
255
255
255
255
255
255
248
248
248
248
248
248
248
248
259
Refer
Name
to page
261
261
261
263
263
263
263,
283
263
263
273
273
273
314
263,
273
263
135
PARAMETERS
5