Mitsubishi Electric FR-F800 Instruction Manual page 290

Setting
Signal
Positive Negative
name
logic logic
11 111 RY Inverter operation ready
12 112 Y12 Output current detection
13 113 Y13 Zero current detection
14 114 FDN PID lower limit
15 115 FUP PID upper limit
PID forward/reverse rotation
16 116 RL
output
17 ― MC1 Electronic bypass MC1
18 ― MC2 Electronic bypass MC2
19 ― MC3 Electronic bypass MC3
25 125 FAN Fan fault output
26 126 FIN Heatsink overheat pre-alarm
35 135 TU Torque detection
39 139 Y39 Start time tuning completion Output when tuning is completed during start-up.
40 140 Y40 Trace status
Inverter running and start
45 145 RUN3
command is ON
During deceleration at
46 146 Y46 occurrence of power failure
(retained until release)
47 147 PID During PID control activated Output during PID control.
48 148 Y48 PID deviation limit
49 149 Y49 During pre-charge operation
During second pre-charge
50 150 Y50
operation
51 151 Y51 Pre-charge time over
Second pre-charge time
52 152 Y52
over
53 153 Y53 Pre-charge level over
Second pre-charge level
54 154 Y54
over
57 157 IPM During PM motor control
64 164 Y64 Control circuit capacitor life
Emergency drive in
65 165 Y65
operation
Fault output during
66 166 ALM3
emergency drive
67 167 Y67 Power failed signal
24 V external power supply
68 168 EV
operation
70 170 SLEEP PID output interruption
Function
Output when the reset process is completed after
powering ON the inverter (when starting is
possible by switching the start signal ON or during
operation).
Output when the output current is higher than the
Pr.150 setting for the time set in Pr.151 or longer.
Output when the output current is lower than the
Pr.152 setting for the time set in Pr.153 or longer.
Output when the value is lower than the lower limit
of PID control.
Output when the value is higher than the upper
limit of PID control.
Output during forward rotation under PID control.
Used when using the electronic bypass function.
Output when a fan fault occurs.
Output when the heatsink temperature reaches
about 85% of the heatsink overheat protection
operation temperature.
Output when the motor torque is higher than the
Pr.864 setting.
Output during trace operation.
Output while the inverter is running and the start
command is ON.
Output after the power-failure deceleration
function operates.
(Retained until canceled.)
Output when the absolute deviation value exceeds
the limit value.
Output during pre-charge operation.
Output when the pre-charge operation reaches
the time limit set in Pr.764 or Pr.769.
Output when the measured value before reaching
the ending time during pre-charge operation is
higher than the detection level set in Pr.763 or
Pr.768.
Output while the control method is PM motor
control.
Output during retry processing.
Output during emergency drive operation.

Output when a fault occurs during emergency
drive operation.

Output when the power failure time deceleration-
to-stop function is activated during output shutoff

due to power failure or undervoltage.
Output while operating with a 24 V power supply
input from an external source.
Output during PID output suspension function
operation.
(M) Monitor display and monitor output signal
Operation
Refer
Related
to
parameter
page
― 292
Pr.150, Pr.151 296
Pr.152, Pr.153 296
Pr.127 to Pr.134,
378
Pr.575 to Pr.577
Pr.135 to Pr.139,
363
Pr.159
Pr.244 233
― 543
Pr.864 298
Pr.95, Pr.574 359
Pr.1020 to Pr.1047 433
― 292
Pr.261 to Pr.266 426
Pr.127 to Pr.134,
378
Pr.575 to Pr.577
Pr.127 to Pr.134,
378
Pr.553, Pr.554
Pr.127 to Pr.134,
Pr.241, Pr.553,
Pr.554,
402
Pr.575 to Pr.577,
Pr.753 to Pr.769,
C42 to C45
Pr.71, Pr.80,
149
Pr.998
Pr.65 to Pr.69 236
Pr.514, Pr.515,
Pr.523, Pr.524, 238
Pr.1013
Pr.261 to Pr.266 426
― 57
Pr.127 to Pr.134,
378
Pr.575 to Pr.577
289
PARAMETERS
5
GROUP
M