Verify An Outgoing Call - Patton electronics SmartNode Series Software Configuration Manual

SmartWare Software Configuration Guide
•
09:00:43 CFXS > [EP PHONE] Play tone: ringback-tone
played to the phone. This means that the call arrived correctly in context CS, and has reached its destina-
tion.
• If the above line does not appear, the call has arrived in context CS, but has not reached its destination.
Continue debugging call-router and the outgoing call to the destination signaling protocol.
• If you want to see the dialed digits in the debug monitor, use "debug media-gateway control".
•
09:01:01 CFXS > [EP PHONE] Change state to CONNECTED.
the call is now established.

Verify an outgoing call

Make sure a call from context CS is accepted by the connected POTS terminal. The port is bound to a context
CS interface named PHONE.
The simplest way to verify the signaling of an outgoing call is to use the built-in call generator. You can place a
call to any called-party, and verify that the connected phone is ringing.
unit>enable
unit#configure
unit(cfg)#debug ccfxs
unit(cfg)#debug fxs
unit(cfg)#call 1 dial 2 dest-interface PHONE
unit(cfg)#09:13:55
09:13:55 CFXS
09:13:55 FXS
09:13:55 FXS
09:13:55 FXS
09:13:56 FXS
09:14:00 FXS
09:14:01 FXS
09:14:02 FXS
09:14:02 FXS
09:14:02 FXS
09:14:02 FXS
09:14:02 FXS
09:14:02 FXS
09:14:02 CFXS
09:14:02 CFXS
09:14:02 FXS
09:14:02 FXS
09:14:02 CFXS
Explanation:
•
unit(cfg)#09:13:55 CFXS > [EP PHONE] Change state to RINGING.
the state to RINGING, that means it has accepted the call.
•
09:13:55 FXS > [0 1] Set state to 'Ringing'
that the binding of the port to the context CS interface is correct, and your phone should now be ringing.
• If the phone does not start to ring, revise the binding of the port to the context CS interface, and the con-
nectors of the POTS line.
Debugging call signaling
CFXS > [EP PHONE] Change state to RINGING.
> [EP PHONE] Start Ring.
> FXS-00/01: state=on-hook, event=ring-start
> [0 1] Set state to 'Ringing'
> FXS-00/01: new state=ringing
> [0 1] Set state to 'RingPause'
> [0 1] Set state to 'Ringing'
> [0 1] Set state to 'RingPause'
> [0 1] Off hook.
> [0 1] Notifying off hook.
> FXS-00/01: state=ringing, event=off-hook
> [0 1] Set state to 'Idle'
> [0 1] Set state to 'Active'
> FXS-00/01: new state=off-hook
> [EP PHONE] Change state to CONNECTED.
> [EP PHONE] Stop ring.
> FXS-00/01: state=off-hook, event=ring-stop
> FXS-00/01: new state=off-hook
> [EP PHONE] Change datapath direction to send/receive.
: The called-party is ringing, alerting-tone is
: the called party has accepted the call, and
: The context CS interface changes
: The port begins to ring on the analog line. This means
52 • VoIP debugging
624